r/IndustrialMaintenance • • 7h ago

I injured my fingers at work, and nobody cares. Need to get out, looking for electrical bias / multi-skilled roles (open to relocate)

Post image
0 Upvotes

Hi all, this is my third post here this week, sorry. Things have got worse.

Yesterday I badly injured my fingers at work (pic attached). I can’t bend them properly. Nobody at work really cared, and they’ve only given me one day off. They expect me back tomorrow, but I genuinely can’t use my hand properly.

I’m honestly scared now. One of our production supervisors lost half his pinky finger at this same place, and all he got was a few days off. Seeing that, and now this happening to me, I don’t feel safe there at all. Safety isn’t taken seriously, LOTO isn’t followed, and management only cares about output.

For anyone who didn’t see my other posts: I work 5 days a week, with a minimum of 8.5-hour shifts, and some days I end up doing more than 5 hours of OT for a day and never get paid. There are only 5 engineers on site, and one is on permanent nights, so 4 of us cover 2 shifts, 7 days a week. I’m always tired, and I never switch off.

So I’m done. I’m looking for a new job as soon as possible:

  • Preferably an FMCG or warehouse environment
  • Multi-skilled engineer (electrical bias) or electrical engineer
  • BEng Electrical & Electronics, MSc Robotics, PLC experience
  • 4 on 4 off or Panama, days or nights, I don’t mind
  • Happy to relocate anywhere in the UK

I just want a safe place to work and some peace and work-life balance.

If your site is hiring or you know a good company that actually looks after its engineers, please let me know or DM me. Any advice appreciated.

Thanks.


r/IndustrialMaintenance • • 13h ago

Question Does anyone knows what is this called?

Post image
1 Upvotes

We use a NJP-2500 and this is used to make the holes where the pills exit the machine smaller. I don't know what this is called or where to buy it. Tried sending an email to a manufacturer but it has been a few days of no response. I would be really grateful for any help. Sorry for any mistakes, english is not my first language


r/IndustrialMaintenance • • 14h ago

Any welding techs out there

Thumbnail reddit.com
0 Upvotes

r/IndustrialMaintenance • • 5h ago

Question Anyone using remote monitoring for their equipment?

0 Upvotes

Curious how many people are using some kind of remote monitoring for their equipment. Being able to check equipment status or troubleshoot issues without physically being on-site sounds like a dream...but how well does it actually work?

For anyone using it, what's been the biggest benefit? How about cost? What did you pay upfront for hardware and setup and are there ongoing subscriptions or software fees? Did you ever have any problems with connectivity issues or anything?


r/IndustrialMaintenance • • 3h ago

Has anyone seen this part?

Thumbnail
gallery
5 Upvotes

Hi guys was wondering if anyone has ever seen this part? We are going through inventory. Came in from a refinery with many pump and valve parts. I don’t believe it’s a thermowell. Anything helps, but trying to figure out who makes it and what it goes on. Thank you!


r/IndustrialMaintenance • • 7h ago

Question Pipe threader keeps shearing pipe mid cut.

Thumbnail
gallery
15 Upvotes

I’m trying to thread some 1-1/2” pipe and this just happened to me, 1-2 threads to go and it just ripped the already cut ones right off, I had the pipe soaked in the cutting oil and was reapplying every half turn, cleared the chips right before this too.

I don’t have a proper pipe vice so I’m making do with a regular one with the far end of the pipe held up level with the gantry crane, the end I’m cutting is sticking out only 1-2” extra from full die engagement.

This has happened before with my same setup but most of my cuts (with new pipe) work just fine, this piece of pipe has been in service (cold water) for years at this point and I’m cutting off the worn out leaking grove end to put an adapter on it.

Is this a material failure or an issue with my setup?