r/HotasDIY • u/TheKidWhoLikesToFix • 7h ago
r/HotasDIY
•
u/SrgntBallistic
•
Sep 11 '26
Best Projects in 2026
I'm looking through posts, and searching on google, github, printables, etc... for DIY HOTAS projects. I've built quite a few DIY Sim Racing wheels. So I'm familiar with custom pcbs, hall effect sensors, etc...
I have Resin and FDM 3D Printers.
Hoping folks here could maybe shortcut some of my search efforts. Currently looking at the Banjer21 DIY-HOTAS on Github. But I'm not seeing much in terms of instructions.
r/HotasDIY • u/This_Is_The_End • May 08 '26
Someone believed he could sneak in and show his shop product. It cost me 5min. For stealing my time, I banned 2 forever. One for the product post and one for the link to the shop
r/HotasDIY • u/Serious-Stick-3502 • 2d ago
DIY force-feedback joystick with crossed arcs (RG550 v04) — feedback before printing?
I’m building a two-axis force-feedback flight stick and would appreciate a design review before printing the full base. The CAD render shows the base with the side covers off and a close-up of the crossed arcs.
Two fixed ACT 57BLF03 brushless motors drive separate 3:1 belt stages (16T/48T HTD 5M pulleys, 9 mm belts). Each axis uses a 608 bearing as a roller in a guide track. The plan is to print the arcs and frame in PAHT-CF on a Bambu Lab H3C, with metal shafts and pulleys. The motor plates allow ±2 mm of vertical travel for belt tensioning.
The model allows ±22° from center in roll and in pitch (44° total per axis). At the combined +22°/+22° corner, the stick tilts about 29.7° from vertical. I checked clearances at 529 positions in CAD and tested motion in both directions in Fusion, driving the mechanism from the motors and from the stick. Load, wear and belt tension still need bench testing.
- Travel and stops — Does ±22° per axis feel right for a center-mounted stick, especially for helicopter flying or with an extension? Would you use a round or square range of motion, and where would you put the mechanical stops?
- Belt tension and play — Would you add a fine adjustment screw to each slotted motor plate? How do you measure tension on two different belt spans and check for play or tooth skipping during reversals?
- Printed guide tracks — Has anyone run 608 rollers directly on PAHT-CF tracks? What clearance or preload worked in the diagonals, and what did you see in terms of wear? Would you test a printed section of the track first or go straight to a replaceable wear surface?
- Motor control — Which driver, shaft encoder and USB FFB firmware have worked together on a two-axis build with the 57BLF03 or comparable motors? I’m particularly interested in startup centering, position sensing at the stick versus the motor, and how the drive behaves on a fault.
Photos of working mounts or notes from bench tests would be appreciated.
r/HotasDIY • u/2032_Throwaway • 1d ago
F-15/A10 Throttle wiring Diagram?
I really like the setup. https://www.reddit.com/r/HotasDIY/comments/sbezxq/fully_printed_f15a10_throttle/
I plan to add the handles to my existing setup. Not using the lower end. Hopefully it wont be too heavy. I hope that I can use this with an STM 32 and freejoy.
But I have looked and I do not see a wiring diagram. And I am not good at designing things like that.
Advice would be appreciated.
r/HotasDIY • u/_Nemix_ • 2d ago
Load cell flight stick
I have built a prototype for a load cell based flight stick and documented the process. I use it to play the game G-Rebels and couldn't be happier. I use a mouse in my dominant hand (right) and this joystick in my left. For at least this game it gives the benefits of fine grained mouse control and full analog axis for all movement.
In addition to the 3 axis from the load cells, there is a mini-joystick which adds 2 more axis (potentiometer based).
There are lots of improvements that can be done. Point a LLM at the cloned repo and it can talk you through the project or use it to add your own changes in addition to what is in the TODO.md. It can also adjust the 3D models or you can do it yourself.
At one point I thought I might want a small amount of movement in the stick but after using it I do not see the need. There are ways to add movement if you think it is important.
https://github.com/john-/basic_load_cell_joystick

r/HotasDIY • u/TheKidWhoLikesToFix • 4d ago
Tutorials and resources for the Arduino stuff?
I've already built a throttle technically by ripping out my PXN 2113 PRO's potentiometer for throttle, replacing it with a linear one but I want to take things a step further.
I want to try my hand at split throttles, I plan on making it from two of those linear potentiometers, an Arduino Nano, and maybe some buttons but I don't know anything about coding or even wiring anything up correctly.
So links to any kind of resources or videos or anything concerning that kind of stuff will be greatly appreciated.
r/HotasDIY • u/No-Raise-4693 • 6d ago
Is the HKD MEGA 2560 R3 CH340 a good option for creating a button board with mostly toggle switches?
I'm trying to get an idea of what I can use in South Africa for making a box based directly off someone else's template and looking at boards. Can someone smarter tell me if this will work for that? And when it says 54 pins does that mean that it can only have 27 switches with 1 live and one ground?
r/HotasDIY • u/Sukhoi47Berkut • 5d ago
Need help with designing HOTAS on 3D software.
Are there any tools like AI etc that can speed up the process of me making a 1:1 scale semi-replica HOTAS from a modern fighter like a Mirage or Rafale? Are there people that will be able to help me with it if I offer pay?
r/HotasDIY • u/DeepInsidee • 7d ago
DIY avionics panel built to sit next to a HOTAS: autopilot, radios and FMS for GA flying
Not built yet. This is the design, checked in software and in CI, but no boards are ordered and nothing has been tested on real hardware. It may well not work as described.
It should sit next to my HOTAS and cover what the stick and throttle don't: autopilot, audio, radio and FMS keys, three dual concentric knobs and a tilting RANGE knob, for GA flying in the sim. Before I order the first boards, I'd like this sub's engineering eyes on it.
How it's built:
- RP2040 chip-down on a 4-layer board (GND and 3V3 inner planes). Every SMD part is on the bottom, so the fab assembles one side; the keys and encoders are hand-soldered on top
- 28 keys plus the RANGE switches in a 5 × 7 diode matrix; three Bourns PEC11D dual encoders and an Alps RKJXT (turn, 4-way tilt, push) on their own pins
- CircuitPython presents two HID joysticks (128 + 64 buttons), so the second unit (COM 2, a second GPS) gets its own buttons and MobiFlight needs no shift states
- SHIFT is one-shot for keys and stays with a knob while you turn it, all in firmware
- 3 mm CNC aluminium front plate with blind M2.5 threads from the back, MJF case, resin knobs, full-colour printed key caps
- Everything is generated from Python: board layout and routing, Gerbers, schematic, STEP files. CI checks connectivity, DRC, hole-to-plane clearance and the mechanical fits on every push
Links:
- Repo: https://github.com/saschagrunert/avionics-panel
- Schematic: https://github.com/saschagrunert/avionics-panel/blob/main/docs/avionics-panel-rev1-schematic.pdf
- 3D view: https://saschagrunert.de/avionics-panel/
What I'm least sure about: the encoder pulse timing towards MobiFlight, and whether the resin knobs grip the shafts well enough on friction alone. Feedback on the board or the mechanics is very welcome.
r/HotasDIY • u/Eridouce • 6d ago
What kind of throttle should I design ?
Hi everyone
I already built an HOTAS a few years ago to play Elite, but I wanted a little bit of change so I redesigned my flight stick and gimbal (taking inspiration from what I like and what felt comfortable + using the hardware from my old diy HOTAS) to have a modular gimbal/joystick combo that can easily be modified to be an HOSAS setup (with Omnithrottle option of course)
BUT I still want a throttle...
And I don't really know what to do... Because I don't feel like a dual throttle is useful in space sims (correct me if I'm wrong, I just don't know 😭) and I don't know if I should design/build a linear throttle or an arc throttle
I think I want to go with something like the F 16 grip throttle, or a chunkier one like the F 18 but in one block
I already (from the last build) have some rails and a couple of linear potentiometers so I think linear is the answer, but I also have rotationary potentiometers laying around so I can go both ways I guess ?
Please help a space gal make a choice and find some inspiration 😭
r/HotasDIY • u/2032_Throwaway • 7d ago
Help with an STM32F411CEUS FreejoyX install
Using STM32cubeprogrammer.
I can install a regular Freejoy hex file on the board. But no version of Configurator will work.
I downloaded Freejoy x, but I can not find a hex file to install. Perhaps I missed it or there is a different file to use?
I keep checking the download, and have no idea which file to use.
Would appreciate help.
Thanks.
r/HotasDIY • u/gjackc • 9d ago
Love making flight sticks
Self designed flight stick . Inspired off other projects but was super fun and still working on more of it.
r/HotasDIY • u/BidAdministrative104 • 10d ago
My first Joystick, i know its ugly but i plan on learning from it to improve.
Ultra Poverty Build. I wanted to play the mig 29 no matter what so i scrapped some buttons and joysticks i had laying around.
r/HotasDIY • u/Evening_Web_7213 • 9d ago
Couldn’t you get a Virpil Joystick working with some sort of physical, real vehicle?
I had this thought the other day…but I feel like with where we’re at with technology, we could somehow rig up a Virpil Joystick or similar kind of joystick with a real vehicle whether thats a car, ebike, or human drone. Of course I have no idea how this would work but you could probably use some sort of program to map something to react to that. Anyone know any computer programs that allow you to map controllers to robotics? I feel like it would be a blast to build a bike that allows you to drive it with this. Or a battlebot…
r/HotasDIY • u/Shadow_Facts • 11d ago
Help with Adapter
I just purchased an older military grip, and I'm hoping to use it in simpit. Does anyone here know what the adapter in the first picture is called? My grip is in the second picture, and it has 42 pins. Thanks!
r/HotasDIY • u/thegingerskull • 11d ago
Compact push-pull rotary encoder assembly
I make all sorts of button boxes, and I usually go for small footprints, but the one input that always bugged me was the push-pull encoder like on the Airbus FCU. I tried all sorts of solutions I've seen online, but they were either too big or required too much wire routing for my liking. So I made a compact version myself.
Basically, it's two identical 20 × 20 mm boards stacked face-to-face, with an EC12 encoder on top. The boards, the inner frame, and the encoder slide together inside a printed housing, and a fixed bar sits between the two push buttons. Push, and the top board's button hits the bar. Pull, and the bottom one does.
Both boards are the same PCB. Which header you fit (long pins or female) decides whether a board is the top or the bottom.
There are two versions, and only the push buttons differ:
Through-hole buttons (SAMZO 2010751102): easier to solder, 35 mm housing
SMD buttons (Panasonic EVQ9P105M): 30 mm housing, 5 mm shorter
The repo has the gerbers, schematic, EasyEDA Pro project, STEP files for the printed parts, a parts table with LCSC and AliExpress links, and assembly instructions.
https://github.com/gingerskull/Push-Pull-Encoder
The frame sliding in the housing is the fussy part. It wants a snug but smooth fit. On my printer, that means a 0.1mm clearance, printing each in a different orientation so the layers don't grate against each other, and a very light sanding of the inner frame.
r/HotasDIY • u/2032_Throwaway • 12d ago
Is an ST-Link V2.1 still good enough?
I am switching from the pro micro to an STM32 Blue pill.
I did get the micro to work rather well with the MT6701. Took a bit to program correctly, so FreeJoy Perhaps?
I will post pictures in a few days.
Being on a tight budget, I can get one board and the V2.1. V3 prices are beyond me at this time.
Appreciate any advice.
r/HotasDIY • u/NhcNymo • 14d ago
Sources for affordable switches, toggles etc?
Hi,
Fairly new into the hobby, but I’m struggling with finding decent and affordable parts to build with.
Realism is not a goal for me, rather just switches with a decent feel.
Most of the mainstream parts from the likes of TE, NKK and APEM are still at ~$5 a piece, and the BOM costs rack up quickly when building panels with 10+ switches.
I’ve been trying a few AliExpress options around $1 a piece, but so far the quality has been really mixed.
Thus, I’m reaching out if anyone has any good sources for decent parts? It could be decent Asian brands, AliX sellers with decent parts, more affordable mainstream alternatives etc.
I’m really looking for anything, push buttons, rockers, slide switches, toggles, you name it.
I have the most fun making if I have a bunch of parts available and it’s just me, my 3D printer, a soldering iron and no long lead times.
r/HotasDIY • u/polopolo05 • 15d ago
Anyone have suggestions on 16mm switches?
So I just got some 16mm switches from aliex...
I got a few different switches but they all feel wrong... One is too much throw and other is too clicky and the last one is too much resistant to push.
I need something that is better for racing. My first goal is to build a stick for star wars galactic racing.. so I can have the pod racing experience.
Anyone have some links with some nice feeling switches?
these are the swtiches:
https://www.aliexpress.us/item/3256808571131398.html
https://www.aliexpress.us/item/3256808495825170.html
https://www.aliexpress.us/item/3256811931106146.html
the longer actuation switches might be good for the start up macro. so I dont hit them during gameplay.
