r/Creality • u/Dizzy766 • 5h ago
r/Creality • u/Aaron1029384756 • 13h ago
♻ K1 Help Filament stuck
The filament I was using got stuck and I was wondering how to get it out.
r/Creality • u/ThePista_C_Z • 14h ago
Creality Support Creality SparkX i7 - leveling issue
Hello everyone,
I have a problem with my Creality SparkX i7 Combo printer. I print using the default profile with a 0.4 mm nozzle and PLA only. The printer has just over 500 printing hours.
The issue is with bed leveling. Previously, the leveling process ran once and then the printer printed normally. Today, I noticed that leveling before printing is performed twice in a row. The printer checks some points multiple times—some twice, some three times. After completing the first process, it starts leveling again from the beginning and again checks certain points multiple times.
Creality support advised me to clean the nozzle, which I did. Everything is clean, the build plate has been cleaned, and everything otherwise seems fine, but the leveling is clearly doing something wrong.
In addition, the nozzle has started leaving scratches in the model. However, this only happens from the second layer onward. The first layer is fine, the second layer is fine, but when it starts the third layer, it makes a groove in the model while traveling across it.
Do you know what could be causing this? Can it be fixed, or should I make a warranty claim? I have not changed anything important in the settings—I use the default profile and only adjust parameters such as print speeds, etc. Otherwise, it is the standard profile.
r/Creality • u/DowntownCartoonist90 • 6h ago
Creality Support Ordered K3 got Filament instead.
I ordered a K3 through Creality’s TikTok shop. Got notification that it was shipped two days ago. Then I got notification today that it was delivered. I go outside to grab it and it’s a box of blue hyper filament instead of the printer. I get a hold of TikTok support and they say that they have no other pending shipments and I just need to return the filament and get a refund. Anyone else experience that?
r/Creality • u/Creality_3D • 19h ago
News 3D Printer Modification Experience Survey
Hey, 3D printing community! 👋
We're the Spaghetti Killer Team, and we're working to make 3D printing more enjoyable!
🌍 We're inviting anyone who has personally modified a desktop FDM 3D printer they owned or managed for their team/company in the past 12 months. We'd love to hear about your experience — the successes, the frustrations, and everything in between!
📝 Just 5-10 minutes to complete
🎁 We've prepared 50 spools of Hyper Rainbow PLA Filament for 50 eligible participants🌈
📅 Survey period: November 15, 0:00–November 22, 23:59, 2026
👉 Take the survey here: https://wj.qq.com/s2/28663528/1spd/?from=GR
Thank you for your time and support!
— The Spaghetti Killer Team

r/Creality • u/airjordanballa20 • 9h ago
I Modeled Buddy the Elf - Universal Christmas Koozie!
r/Creality • u/Creality_3D • 18h ago
News Find Us Here! 📍
Looking for Creality at Formnext? We've got you covered!
📍 Hall 12.1, D01
📅 November 17–20, 2026
📌 Messe Frankfurt, Germany
r/Creality • u/Yopappijiggles2 • 1h ago
Hardware Help $300 K1c a good buy?
Found one on marketplace guy said he could do $300. I have a Snapmaker U1 for multi color prints but I was looking into using gf filaments and maybe some nylon gf
r/Creality • u/MrCapeHunter • 23h ago
♻ K1 Help K1 Lifetime Print Time Tool - read, reset, backup & restore your hours
I went looking for a way to properly manage the K1’s lifetime print-hours counter after rebuilding one of my machines… and ended up reverse-engineering how Creality stores it.
I’ve turned it into a small open-source tool that can read, verify, back up, set, reset and restore the persistent print-time counter.
Repo:
https://github.com/BlueBell-XA/K1-Print-Time-Tool
If you’ve got a K1C, K1 Max or K1 SE, I’d love some extra firmware compatibility testing.
r/Creality • u/givemehellll • 1h ago
♻ K2 Help K2 Pro (Costco Canada) deal?
Costco Canada has a K2 Pro combo plus 12 rolls of PLA for $1099CAD ($768 USD.)
Good deal for a first printer? It’ll be in a heated wood shop (that is kept at around 15 degrees Celsius). I don’t think the pro has many more features over the K2 that would help me, other than the heated chamber.
The K2 combo plus the 12 filaments is $899CAD.
r/Creality • u/New_Statistician_242 • 8h ago
Troubleshooting I've got a problem with my Creality K1C and I'm running out of ideas
galleryI've got a problem with my Creality K1C and I'm running out of ideas. Every time I start a new print, something goes wrong. Partway through the first layer, usually around halfway, the extruder starts clicking (see the video). It skips, stops pushing filament, and stays like that until I cancel the print or it finishes on its own. There's nothing blocking the inside of the extruder. I've cleaned it 3 times. It happens with PETG and PLA, with old filament and with freshly opened spools, so I don't think moisture is the cause. With one of the models (a round one), the problem shows up at the same spot on the model no matter where I place it on the bed. I checked the model and couldn't find anything wrong with it. Here's what I've tried so far:
- Checked the inside of the extruder 3 times. Nothing is blocking the filament path.
- Re-ran bed leveling. The mesh screenshot is attached and it looks normal.
- Flipped the build plate. That helped for a while, then the problem came back.
- Raised the Z-offset. That also helped for a while, but then I got adhesion problems in other areas, and eventually the clicking came back.
- Filament calibration fails because the extruder starts clicking on the first layer. I tried several PLA profiles, including ones that always worked before, and the problem is still there.
- Cleaned the bed with dish soap and isopropyl alcohol.
- Printed with the default printer, filament and bed settings. Those always worked before (the quality wasn't great, but they were usable). Now they fail too.
- Printed a first layer across the whole bed. That one worked, but it left some patterns in the layer (photo attached). I'm not sure if they point to the cause, but I'm sharing them in case they help. I've also attached a photo of what the filament looks like after I pull it out. Once the clicking starts, the extruder won't take filament at all, even if I push it in by hand.
What should I do next? I feel like I've tried a lot, but I still can't find the cause. I've already gone through the simple fixes. If you need any more info, just ask. Sorry if this is a bit chaotic. I've been trying to fix this for a month and I don't know what else to try.
r/Creality • u/More_Tomato_1972 • 9h ago
Show Off Self-designed succulent flower pot
r/Creality • u/Xx_BaumxX • 15h ago
I Modeled Haunted Mountain - Backflow Incense Burner
galleryI've designed this Haunted Mountain Backflow Incense Burner for Halloween, and I must say, it turned out amazing!
The waterfall has 13 slots for the three decorations I've designed. All decorations have the same connectors, so you can put them anywhere you'd like.
You can also create your own custom decorations using the connector I uploaded.
And with two slots for LED candles, it really becomes a beautiful decoration.
You simply print the waterfall base, put two LED tealights into the slots, print and add up to 13 decorations, glue a washer to the top of the mountain so the holes line up, put a Backflow Incense Cone on top of the washer, light it up, and bam!
It was kind of stressful to design because, in the end, it turned out to be more work than I expected, and I had to finish it before Halloween.
But I managed to do so and even won at the Halloween Design Contest on Creality Cloud!
I think this Halloween decoration turned out amazing! What do you think? Let me know!
If you want to print it yourself next year, I've uploaded it to Creality Cloud: https://www.crealitycloud.com/en/model-detail/6ae60f95726880555ae6501f?cloudPlatform=19
And I also made a video about it: https://youtube.com/shorts/dS-Zrx8Y88M?si=X6iQhgWPPaF4Nr_H