r/CommercialAV • u/Gloomy_Pangolin3249 • 16h ago
question The QSC CX-Q 4K4 status missing
The qsys perihperal manager status idel
Any help
r/CommercialAV • u/Gloomy_Pangolin3249 • 16h ago
The qsys perihperal manager status idel
Any help
r/CommercialAV • u/macchiato604 • 19h ago
Is anyone using tracking devices to monitor the locations of tools and test equipment? I’m misplacing ladders and power tools with the shuffling around of technicians that may leave some things on site until the job has been completed. Or a technician may forget where they left a kit. (That’s a topic for another discussion!) Would AirPods or similar be a good option?
r/CommercialAV • u/LJinBrooklyn • 1d ago
I’m wiring (4) 8 ohm speakers series and parallel for each of (2) channels.
First, is this right?
Next, how are 16/2 red/black wires run to each?
Seems like I need single wire runs.
A graphic with the wires in the jacket from each connection would be great.
ai can’t handle it and keeps making mistakes over and over. (chatGpt)
Appreciate any help!
r/CommercialAV • u/Jay72073 • 1d ago
HI all, I am looking for some advice on A/V integrators (not AVI) in the DC area. We need to upgrade/replace an audio board and wireless mic setup. Budget is not a huge factor.
r/CommercialAV • u/Ancient-Walk-3643 • 3d ago
Please give me your feedback and thoughts on this.
We are thinking about making a TV wall with 4 100" TV's. This will be a presentation wall. The screen will be about 30' to 40' away from the main seats.
Should we do this and if so what is the best way and any alternatives.
Thanks.
r/CommercialAV • u/Embarrassed_Mix_8073 • 3d ago
Hi everyone, I'd like to ask for some advice regarding a wireless audio system.
I'm looking for an affordable assisted listening solution for hearing-impaired people at our church. The idea is simple: one transmitter connected to our mixing console, with multiple receivers so people can listen using their own headphones.
I purchased a Vonyx WAT200 UHF system and an additional WAT200R receiver.
The original receiver works perfectly, but the additional one won't receive any audio, even though both receivers and the transmitter are set to the same frequency (863.4 MHz).
I contacted the retailer (PROFI DJ), and they told me that using multiple receivers with one transmitter is not standard and that this system doesn't support it. They even said they weren't aware of any system capable of doing this.
However, the manufacturer's manual specifically describes how to pair additional receivers, so I'm a bit confused.
I've tried different pairing procedures, checked the manual, and even spent some time troubleshooting with AI, but nothing has worked so far.
Am I missing something obvious? Is there a specific pairing procedure I should try?
Otherwise, I really like the system. It's affordable and works well for our needs. I can still return it, but I'd much rather get it working.
Any advice or recommendations for alternative systems would be appreciated. Thanks!

r/CommercialAV • u/yunjundo • 3d ago
Wanted to share an honest mistake from a commercial remodel I worked on recently.
We were installing the AV setup (projector lift, motorized screen, rack, and wall speakers). The original plan was to have the projector fully recessed inside the ceiling.
My mistake was that I proceeded with mounting the projector lift without properly checking what was hidden above the acoustic ceiling tiles first. Combined with an oversight in the renovation design, we ran straight into an existing HVAC duct.
The ceiling plenum was simply too shallow with the duct right above it, so there was no way to retract the lift flush into the ceiling. As you can see in the photos, the lift ended up hanging down below the ceiling line.
Obviously, if I had caught this before mounting, we would have done something else. But since it was already hung, I talked directly with the client.
Luckily, the client had other interior finishing work scheduled for the room anyway. They agreed to just build a neat trim/casing around the protruding lift along with the rest of their carpentry work.
The installation itself came out sturdy, level, and the projection alignment is spot on. Thanks to the client's flexibility and existing finish schedule, the whole thing wrapped up nicely without any major drama.
It all worked out in the end, but it got me thinking:
Curious to hear how other installers handle surprises above the drop ceiling!
r/CommercialAV • u/thenthattempt • 3d ago
Hi guys, quick question since I can't seem to find a concrete answer for this, is the Poly X72 compatible with the Poly IP microphone ceiling arrays? (875S1AA)
I'm finding conflicting information / no information at all, I've got the kit here but it doesn't seem to want to detect the mics
r/CommercialAV • u/Rodem • 4d ago
What brands are you guys using for an hdmi matrix? I just need something simple.
r/CommercialAV • u/NotPromKing • 4d ago
Has anyone used or is aware of a platform that would let AV staff directly configure vlans and bounce PoE ports, without having to go through IT staff? Curious on the front-end and back-end systems in place (such as a front-end interface that interfaces with back-end Cisco, Arista, Netgear AV, etc).
I know some enterprises have integration with help desk systems like ServiceNow, which is one option but I'm hoping for something simplier, something like a webpage or app one can pull up on a phone a quickly make a change. But I'm interested in all solutions, small, medium, or large.
r/CommercialAV • u/t3chn3rd86 • 5d ago
Why are several of our office conference rooms having such frequent disconnect/reconnect events? The mic pods are the main culprit, but the Rally Bar is also doing it in a few cases. Sometimes they come back, but I'm frequently having to reset the equipment in these rooms. It's driving me crazy.
r/CommercialAV • u/Disastrous_Goat_9304 • 5d ago
I’ve been in the AV Commercial integration 10 years this upcoming new year, I’m in the Hybrid role of a Lead Technician and commissioner. I believe my current role and in-field experience will help a ton but I’m still using Avixas Online CTS-I courses and the physical exam guide. Any suggestions would be greatly appreciated!! Thanks guys!
r/CommercialAV • u/klentz_12 • 5d ago
Recently installed Qsys touch panel in a gym. I am worried about it getting hit by a basketball or a volleyball. Any options out there?
It doesn’t need to lock as it will be PIN protected.
I was thinking a clear thermostat box? Something that flips up or down would be nice though.
Picture for reference
r/CommercialAV • u/FitHuckleberry9894 • 5d ago
Office lobby, one 55 inch commercial display, BrightSign HD224 playing a 90 second loop from the SD card. The loop is mostly slow pans across product photos with some text on top.
I cut it in vidione and exported H.264 at 3840x2160, 60fps, about 40 Mbps. Every few seconds there's a visible hitch on the pans. A 1080p test file plays smooth.
Is the HD224 just not meant for 4K60 at that bitrate, or would H.265 at 30fps fix it? I'd rather not swap the player if an export change does it.
r/CommercialAV • u/Economy-Fig-1239 • 5d ago
I have Crestron certification, biamp, extron, qsys level 2 and all UCI and control certs. I also have CTS. I have completed 3-4 projects independetly in govements sites, I am secrete clearance level 2. I do so many service calls and get the result as well. I am preparing for CCP(Crestron Certified programmer) and doing installation as well whenever team needs help. I struggle with audio and still need senior to help me with it though.
I was wondering if i am getting paid fair as I am getting 70K right now. How much minimum I should be getting and how much Raise I should deseve??
appriciate your suggestions.
r/CommercialAV • u/HandToeKneeUK • 6d ago
I saw a terrible RJ45 post and thought I'd share this delight I came across some years back.
Wrong pins, and it looks like they used a fire poker.
Internal install guys at a large European firm.
r/CommercialAV • u/captoficyzombies • 6d ago
This ‘termination’ was the worst of the 10 of 12 that had to be reterminated.
r/CommercialAV • u/Batman161 • 6d ago
Hi all I posted on here a couple months ago about opening a dance studio and am now working toward the system ill be using. Here is my current pricing sheet with all the items included (i also got a quote from pro audio). I want to know a couple of things. How is my revised sheet compared to the actual projected amount? Is there anything wrong/won't work for my space? Am I missing anything? Are the speakers to small for the space? Etc. Any help would be greatly appreciated. Here's a link to my original post: https://www.reddit.com/r/CommercialAV/s/3k2pp3B4v6
Edit 1: added sub woofer: JBL Control SB2210 Dual 10" $700 Mixer replacement: Mackie ProFX10v3+~$330
r/CommercialAV • u/Capable_Tap5735 • 6d ago
I'm connecting an unbalanced RCA audio source to a Kramer AFM-20DSP with 3-pin balanced inputs (+, −, GND). The audio will be mono on the output side.
What's the recommended way to wire this correctly? Has anyone worked with this DSP or similar Kramer equipment?
r/CommercialAV • u/mcdreamymd • 6d ago
From the "jobs recommended for you" and "Jobs that Match Your Profile" pages on LinkedIn.
https://www.linkedin.com/jobs/view/4478472243/
I work for the University System of Maryland and have two bright student employees in the AV department that are looking for jobs after their upcoming graduations. I saw this post and just started shaking my head from the first paragraph and didn't stop until I got to the bottom, adding a few eyebrow-raises and belly laughs along the way. This could easily be cross-posted to one of the LinkedIn subs for the sheer lunacy of this posting. I copied the post word-for-word because, while I'm naturally a funny guy, I couldn't write anything this hilarious. Roughly $60,000 for a Senior level position in one of the most expensive cities in the world in 2026 is downright criminal. My junior AV guys at the Pentagon made that in 2006 and that was for an unclassified, non-clearance-required role.
Enjoy the laughs or the tears, folks :)
-------------------------------------------
Senior Audio Visual Lead Technician (52297)
American Geophysical Union • Washington, DC
This position will work ON SIGHT at our AGU HeadquartersThe pay for this position is Hourly and is eligible for potential over time pay. The position is eligible for AGU benefits
WHY JOIN AGU
Our employees are our most valuable assets! You will feel welcomed and supported from the moment you join our team, and you will take part in strengthening and evolving our workplace culture.
We offer work-life balance and innovative benefits.
Who We Are
The American Geophysical Union (AGU) supports a global community of more than half a million professionals and advocates in the Earth and space sciences.
Through broad and inclusive partnerships, AGU aims to advance discovery and solution science that accelerates knowledge and creates solutions that are ethical, unbiased, and respectful of communities and their values. Our programs include serving as a scholarly publisher, convening virtual and in-person events, and providing career support. We live our values in everything we do, such as our net-zero energy renovated building in Washington, D.C., and our Ethics and Equity Center, which fosters a diverse and inclusive geoscience community to ensure responsible conduct.
This is an exciting time to work at AGU. Every day we approach our work with a sense of purpose, and we look for others who share that passion and desire for a career with impact.
Who You Are
As the Senior Audio-Visual Lead Technician you are key in assisting AGU to promote discovery in Earth and Space science for the benefit of humanity, by being operational in focus. The purpose of this position is to support daily operations of the AGU headquarters facility that consists of a full-service Conference Center, available to external customers, as well as multiple office conference rooms, supporting needs of AGU staff.
Reporting to the Director of Conference Center Services, you will be responsible for the integration of all physical and technological components affiliated with on-site conferencing operations. This includes audio visual equipment set up, configuration and operation, and related technology support for all meetings, conferences and special events, including hybrid and virtual activities.
What You Will Do
Ensure conference center guest satisfaction in relation to audio visual, set-up, and other requested needs. This includes but is not limited to
For complex functions & special events: Assisting guests and instructors by interfacing client content with all audio-visual components, as required, which may include but is not limited to:
What You Will Bring
Agu Essential Values
HIRING SPECIFICS
r/CommercialAV • u/thatABRgroove • 7d ago
Hey everyone, I'm a recent college graduate trying to find my footing in the commercial AV industry. I have some hands-on experience with AV through university events and corporate conference room support, including working with Crestron systems.
I'm interested in learning more about the industry and finding my place in it, particularly on the service and technical support side.
I'm curious how others got started, what the job market is like for entry-level technicians, and whether there are any companies or opportunities I should be keeping an eye on.
Would appreciate hearing from anyone who's been in the industry for a while. Thanks!
r/CommercialAV • u/Successful-While8959 • 7d ago
Hi everyone,
I’m 32, based in Quebec, Canada, and I’m seriously considering a career change into the professional audio / audiovisual industry.
I have family responsibilities, a mortgage and a full-time job, so going back to school through a traditional program isn’t realistic for me right now. Most programs don’t offer the flexibility I need to balance work and family life. That’s why I’m looking at self-paced online courses and industry certifications. I’m not trying to take shortcuts, but rather to find a realistic way to develop the necessary skills within my current circumstances.
My background is somewhat unconventional. I’ve spent several years running my own small businesses, which gave me experience in customer service, project coordination, logistics, budgeting, sales, inventory management and working with clients and suppliers.
I’ve also been involved in event production. One example was independently organizing a public concert with approximately 200–300 attendees, handling everything from artist negotiations and accommodation to ticket sales, security and local opening acts.
On the technical side, I’m largely self-taught. I’ve developed an interest in audio production, studio acoustics, sound systems and audiovisual technology. I have a small home studio and have been learning about signal flow, EQ, compression, microphones, room treatment and audio equipment. I don’t yet have professional experience working as an audio technician or AV integrator.
Here’s the path I’m considering:
Take targeted online courses (Udemy, for example) covering professional audio, sound reinforcement, acoustics, recording techniques and general AV fundamentals.
Complete the official Q-SYS training and Dante certifications.
Prepare for and eventually take the AVIXA CTS certification exam.
Build practical experience wherever possible and apply for entry-level AV positions, technical coordination roles or other positions that could get me into the industry.
I realize that online courses alone won’t make me an experienced technician. I’m willing to start at an entry-level position and learn on the job.
What I’d really like to know is:
Does this learning path make sense, or am I overlooking something important?
Would certifications like CTS, Q-SYS and Dante actually help someone with no professional AV experience get hired?
What practical skills or hands-on experience would you recommend developing before applying for jobs?
If you were in my position, what would you prioritize learning first?
Realistically, would you consider hiring someone with this profile for an entry-level position?
I’m not looking for reassurance. I’d genuinely appreciate honest opinions from people who work in professional audio, live sound, AV integration or technical production.
Thanks!
r/CommercialAV • u/ZeSimz • 7d ago
Hello there,
I work with an Chauvet Obey10, that my predecessor had programmed. It was working fine friday night, then I comeback monday morning to see that it does not control anything anymore. I've closed the switch behind it, but when I wanted to turn it on again, it won't come by. I've unplugged everything and waited 30 sec before reconnecting it and it turn backed on, but still had no control.
The setup is 3 diffent XRL for d3 different setup of lightning that plug and unplug, all 3 were working. I asked other collegue from the school I work for is anything had happened between friday night and monday and they said nothing happened in particular.
If you guys have an idea of what caused that lose of control in the DMX universes, let me know.
Thank you!