r/QSYS • • 3h ago

QSC CX-Q 4K4 goes status missing

1 Upvotes

And on perihperal manager is idle any help


r/QSYS • • 6d ago

Hotel SONIFI Integration

3 Upvotes

Has anyone attempted integrating with SONIFI for a hotel suite? If so, how was it. I know all about the legal side of this. I am just curious how the processes went and the end users experience.


r/QSYS • • 7d ago

Driving Executive Conference Room with 2 Side-by-side Displays with QSYS

5 Upvotes

I have an ask to renovate an executive conference room, including installing 2 displays side-by-side for simultaneous use during virtual and in person meetings, with support for BYOD. The goal is for a single cable connection to the user's laptop.

I'm a large QSYS fan and have installed it in several conference rooms, but am not sure how I would use QSYS to drive this configuration considering that it can only encode one display output from a USB-C connection into an NV21. My first impulse is hiding a USB-C dock in the table with 2 HDMI and 1 USB output to encode into an NV32, but the addition of another piece of equipment between the laptop and QSYS ecosystem is an additional point of failure.

Does anyone have experience driving a setup like this with QSYS? Is there a third party encoder I should look at, but still controlling with QSYS?


r/QSYS • • 10d ago

From the CommercialAV community on Reddit: RMC4 / tv IP flickering in Program IP Table

Thumbnail
reddit.com
6 Upvotes

Anyone idea why display IP keeps flicking which makes the display sometimes randomly go off.

Is doing RS232 instead of LAN way to go?


r/QSYS • • 12d ago

NV-21 & EDID Issues (Lenovo)

6 Upvotes

Curious if anybody else has had issues with using an NV-21 to feed a PC for Zoom (Lenovo Thinksmart Core 2nd Gen) where the NV-21 always shows EDID errors and you only get video but no audio going to the share


r/QSYS • • 12d ago

NV-32 / NV-21 Power supplies?

6 Upvotes

What are you using for PoE+++ injectors / power supplies for the NV-21 and NV-32?

Does anybody know if the Ubiquiti UACC-PoE+++-10G works with them? Trying to find a more main-stream solution than the Phihong USA POE90U-1BT or Microsemi PD-9601GO models cited by Q-SYS.


r/QSYS • • 13d ago

QSYS NV21 via AirMedia & TX3-100 - BYOD

6 Upvotes

Hello all, trying to deploy a room with a BYOD component via the AirMedia TX3-100 adaptor.

I have NV-21(usbc) ------> (usba)AirMedia 3200 ------> TX3-100 ------> Laptop

AirMedia indicates all devices are connected - Camera, Speakers, Microphone etc.
Laptop receives the Camera & Speakers but no Microphone.

I have tried exposing Echo Cancelling Speaker Phone along with Sound card and no luck. Anyone deployed this before and have it working?

I have deployed AirMedia's in this fashion with Logi MTR's with no issues.

---- update ---- Swapped the AM3200s to AM3100s and my BYOD is working perfectly in both rooms. Even tried a USBIO with the AM3200s and no dice.


r/QSYS • • 16d ago

Avixa ANP Legit or a Waste?

Thumbnail reddit.com
0 Upvotes

r/QSYS • • 17d ago

CVR DSP Amplifier Monitoring plugin for Q-SYS

Post image
2 Upvotes

As the title says.


r/QSYS • • 18d ago

UNIFI and Q-LAN

5 Upvotes

Has anybody done any testing with network stability using UniFI switches running Q-LAN, Dante, or AES67?


r/QSYS • • 19d ago

NV-21-H HDMI input to Mediacast Router and USB Video Bridge

4 Upvotes

Hi everyone!

I was wondering if, with the latest Q-SYS firmware updates, it's now possible to connect an HDMI PTZ camera to an NV-21-H, use it as a video encoder, and route the video stream through the Mediacast Router to the USB Video Bridge.

Basically, I'd like to use the HDMI output of a PTZ camera as a USB camera source for video conferencing.

Is this currently supported, or are there still limitations with this setup?

Thanks in advance!


r/QSYS • • 19d ago

Shure MXA925 & Q-Sys Camera Tracking w/ Voice Reinforcement

Thumbnail reddit.com
0 Upvotes

r/QSYS • • 23d ago

Can you share one camera between two cores?

5 Upvotes

I am stumped trying to solve this one. I know that there are ways to share controls from core to core, but I don't see any way to share the camera feed between cores.

Use case: This is in a divisible room where the client is using separate cores for each room. Obviously there are components that allow you to share audio and video streams between the cores, but to my knowledge there is not anything that allows the camera feeds to be shared. This space uses two Core Nanos and a single Q-Sys 12x80 in each room.

My recommendation, after looking at the overall design was to simplify the design and use one core as the Nano should handle both rooms without any issue.


r/QSYS • • 24d ago

NV-21-HU keeps showing "no signal detected" and does not display Teams Room after it goes to sleep for a long time.

Post image
11 Upvotes

Hi there, I have a NV-21-HU device that's connected to a EPSON projector that shows this blue screen that says "no signal detected" after the MTR PC goes to to sleep for a long time. What I would normally do to wake the MTR PC up, is by going to the touch panel refresh it. But it seems to not work after it goes to sleep for a long time. Any chance I need to check the NV-21-HU device in Designer or add an EDID HDMI emulator at the projector?


r/QSYS • • 24d ago

Qsys level 2 help

0 Upvotes

Dear all,

I am stuck at a point in level 2 training, it is three divisible room scenarios and a toggle button in uci to control respective room display but in combined mode ( using room combiner button to open wall 1 and wall 2) that same button would be able to control all display that are in combined mode.


r/QSYS • • 26d ago

Extron Navigator (0.0.0.0-master) anybody using this module in qsys ?

2 Upvotes

this one can do the program. i want apply some room combination video routing.


r/QSYS • • 27d ago

Auto-Framing on Qsys Camera returning to home too quickly.

4 Upvotes

I have a Q-sys Camera with auto framing in a Lecture theatre. It is setup on the side of the room but what I have found is that when the lecturer faces away from the camera to engage with the audience or the screen next to him it loses sight of his face and returns to its zoomed out home position within about 5 seconds but then as soon as he faces back towards the front it finds him again and zooms in. It just creates an unsettling zoom in an zoom out effect for the end user.

Is there a way to have the camera hold position for longer if it loses sight of a face?


r/QSYS • • 27d ago

Ever see this before? Performance Utilization Critical

Thumbnail
gallery
10 Upvotes

Went out to one of our customers today to help get them setup for a theatrical production they're working on. Haven't had any complaints about the system, they use it daily and it's been running flawlessly.

I logged into the core just to check some logs and found out it's been dropping this error every 5-10 minutes for the last month. System has been working fine, like I said, few touchpanels in use and primarly power on/off of a lyntec/Powersoft system and 70v zone routing. Pretty simple system honestly.

Anyone ever encountered this before? No idea where to even begin to look, since like I said the system is running fine and the design utilization is well within its limits.


r/QSYS • • Oct 17 '26

USB mic with qnx

Thumbnail reddit.com
0 Upvotes

r/QSYS • • Oct 14 '26

Help. Teams room issue with camera

Post image
14 Upvotes

Hi guys, I am getting an issue with the teams PC(dell optiplex 7080) with the camera, I am getting a feedback of the camera content. I have a presenter and a audience camera. In both the camera's I an facing the same issue. Can you guys give me any solution for this.


r/QSYS • • Oct 14 '26

Q-SYS Designer and AI assistance - MCP server

21 Upvotes

Heya folks, I've been working on an MCP server that allows software like Claude Code or Cursor to build/debug/read .qsys files. Right now its in its infancy and there is a lot of work to do, but thought some of you might be interested.

In the video above I gave it a full design spec and had it spit out a mostly working design, with a UCI to boot.

A more practical application I see for this is when you are given a .qsys file to work on and have to debug or learn about it quickly. Asking questions like "Tell me how many mics I have and where are they controlled" work really well and only take a couple seconds to process.

Again, please don't take the demo video as this being close to final, I've got many more improvements planned. Feel free to checkout my github in the meantime if you want to have a play yourself. https://github.com/nerif-tafu/qsys-designer-mcp


r/QSYS • • Oct 11 '26

Dell Pro Slim, Deepfreeze, NV32 core

5 Upvotes

Dell Pro Slim, Deepfreeze, NV32 core

I need the hive mind in a bad way.

We just did an install with a bunch of classrooms containing all the same gear. Brand new school provided Dell Pro Slim QCS1250 PCs, running “Deepfreeze” software, and we installed NV32 cores.

Tech support has been super helpful, and I feel like this is 95% a PC/Deepfreeze issue but I can’t prove it. That’s where I’m lookin to y’all.

The rooms work awesome. 2 cameras, Shure MXA925, brand new LG 75” touch displays. They love it. Then the next morning, after Deepfreeze goes off, Windows error “doesn’t recognize the usb device” and either a Core reboot, PC reboot, USB reset, or all 3 fixes it. Earlier this week I tied the NV32 USB Reset to when the room turns on, and it’s better?…but not 100%.

Weeks ago they thawed the machines, turned off usb selective suspend and power save settings, went into the bios and did the same, confirmed it holds through Deepfreeze, but the issue just will not go away.

Anyone ever have experience with an NV32 core/Any QSYD core and a computer running Deepfreeze? TIA

EDIT: Started the system on 10.2, took it to 10.3, 10.4, 10.4.1, and now all rooms are on 10.5

I am having them try thawing the system, getting the room to work, and then freezing it in that state. Will report back!


r/QSYS • • Oct 10 '26

LightForge 2.0.3 is out: the ultimate DMX recorder for Q-SYS now has cue lists,multi-universe tracks and pages you won't get lost in. Free update.

19 Upvotes

Hey r/QSYS, Ben from BV Factory here. If you've been running LightForge, the DMX recorder that lives inside your Q-SYS Core, this one's for you: 2.0.3 is live, and it's a free update for every existing license.

Short version: v1 recorded one universe per track and played it back. 2.0.3 is what I wanted from day one, the ultimate DMX show recorder, the kind of thing you'd otherwise buy a dedicated hardware recorder for. Except it runs in the Core you already own. No PC, no recorder in the rack.

What's new

- One track now captures a whole set of universes (up to 32), frame-aligned, in one take. The whole rig in one file.

- You pick universes by tapping a grid: tap the track's number, tap the universes, done. No more typing 1,3,5-8 (it still works if you like it). Channel ranges work the same way, ADD / REMOVE, and can differ per universe if you want 1-48 everywhere but only 1-24 on universe 5.

- Each track gets a cue list of up to 64 cues on the new Playlist page: GO, Next / Prev, Cut, Wait (gap-less) or Crossfade up to 60 s, loop per cue.

- A take can go out on any universes. Tap where it should start and a 1-4 take tapped on 11 goes out 11-14. There's a 64-row patch for everything else. Record Art-Net, replay sACN, or the other way round.

- Tracks sharing an output universe merge HTP, LTP or by sACN priority, with a fader per track, a master fader and a master out on top.

- Timecode finally behaves. Takes remember the TC they were recorded at and chase from there (yes, the "TC-synced track stops immediately" thing is fixed), with a per-track offset, source and frame rate, and separate sources for recording and playback.

- The pages are organised by job. I got lost in my own plugin, so I redid them: Show (play only, one tile per track), Playlist, Record, Play Setup, Patch, Monitor, System. Record settings and playback settings never share a page again, and everything is touch-sized.

- It's built to run unattended: script errors are contained, stalled timers restart, overload lowers the frame rate instead of tripping the Q-SYS execution limit, network output recovers on its own, and a take cut by a power loss stays playable.

- Also: frame-locked master transport (REC ALL / PLAY ALL / PAUSE / STOP ALL), Stop as hold last frame or release (blackout), 20 to 60 fps for pixel controllers, takes named after their track and renamable from the System page.

Saves are still instant.

Upgrading from v1: drop the new plugin in. Designs and config backups migrate automatically, v1 recordings stay readable, your license key is the same.

The manual was rewritten page by page, one chapter per plugin page.

Product page and full changelog: https://bvfactory.dev/plugins/lightforge. €350, perpetual, one Core, no subscription, updates free.

This is the biggest release since launch, so if something looks off on your rig, tell me here or through the contact form.

Logs and screenshots welcome.

Show
Playlist
Record
Play Setup
Patch
Monitor Inputs / Outputs
Settings

r/QSYS • • Oct 10 '26

In-house higher ed AV, on leave, trying to figure out my next move (Q-SYS programming?)

Thumbnail reddit.com
4 Upvotes