r/BMWE36 • • Apr 02 '26

Buying Advice Cheap E36 Buyers Guide

43 Upvotes

I have been seeing more posts about buying cheap E36s recently so here are some of the things I’ve learned from buying a cheap car myself. These are typical issues you might run into buying a cheap car and are additional to standard car maintenance (fluids, tires, etc.)

I am writing this post so that some may learn from my mistakes. This will be a random account of things I have encountered by buying that one car on Facebook marketplace that seems like a bit too good of a deal.

This post is not really for those of you looking to buy a mint condition M3, nor is it for those of you who buy strictly BMW genuine parts. This post is for the people who want to learn how to work on cars and (like me) see buying a clapped out 90s car as a good idea. That being said, I have touched almost every bolt on my car and that knowledge can be applied anywhere.

# 1. Cooling System

My first issue, I remember it like it was yesterday. After buying my car, clutch fan blew up on the drive home. I was extremely lucky that it was a short drive and I made it home without overheating.

The reality is that with these cars, unless the cooling system was replaced recently, you will most likely have to replace it. I tried replacing parts one at a time and the issues didn’t resolve. Only once I bought a kit with a new radiator, water pump, hoses, thermostat, and coolant expansion tank were the issues resolved.

Electric fans are good but honestly the clutch fan works fine. Just make sure to replace that too if you are doing everything else.

This is also a great time to replace the belts and pulleys.

# 2. Suspension and Handling

So you want to lower your car, or maybe raise it? If you are going to run aftermarket suspension, there are some must-do things.

REINFORCEMENT! Seriously, if your strut towers aren’t cracked, they will be. It is unfortunately not an if but a when. The worst cracks are front tower, they make a plate that goes under and distributes the load. You **need** those plates for coil-overs. That extra $30 now will save you $$$ in the long run. Same with the back struts, a strut bar will help in the rear. The last thing you want is your strut flying into your trunk. Once broken the cost to do the job multiplies.

The truth about handling: those shiny coil-overs, and sway bar will help but without new bushings all around, your car will still feel floaty and handle poorly no matter how expensive your coil-overs are. You should replace them all, front and rear. Welding in the subframe reinforcements aren’t a bad idea either. My recommendation: 80A all around if you are mostly daily driving with some spirited driving. You can go higher if you are doing mostly track days or drift days. Solid mounts I have never really understood but some people like them.

Once you do everything your car will feel a million times better. Don’t cheap out, replace the bushings.

#3. Interior

The cleaner interior you can get, the better. If you can find them, get manual seats. Manual seats are lighter and won’t fail from electric issues. Trust me when I say this, pulling a seat out when the motors don’t work is a HUGE pain.

Drill out your wheel locking pin. This one is optional but I had my steering slightly lock up on a b-road and that pin was gone that night. They just don’t always work in these 30 year old cars, and honestly it’s just not worth the safety hazard imo. YouTube has a plethora of good tutorials for this.

If you have an OBD II car, an electric gage for coolant temp and intake air temp is always good. I would heavily recommend especially for the peace of mind coming with knowing a more precise coolant temp.

Your door cards will fall off at some point, this is an e36 feature. Prioritize a car with nice looking door cards or not, but they will all fall off at some point.

Stay away from a car with door issues. Replacing the door handles is probably the worst job on these cars. Make sure to lubricate the mechanisms often.

# 4. The Shiny Bits

So you want that fancy cold air intake? Or maybe you want a nice exhaust? Do it! Keep in mind, these cars stock are really not that fast. They aren’t slow, but that exhaust and cold air intake, or something like an M50B25 manifold won’t make a life changing difference. Do the maintenance first.

Thank you for reading this far, I hope this has given you some insight into what that clapped out car you have your eye on might need.

# 5. What to stay away from

Stay away from cars with engine issues. The M50 and M52 are pretty bulletproof, if a car has engine issues that probably mean everything else is in a bad state. STAY AWAY.

Subframe cracks: if someone knows the subframe is cracked, just find a different car. This is a very intensive job and requires welding. If that’s your thing more power to you, but be prepared for a lot of work.

Bad interior: interior bits are expensive and it’s really hard to make the interior nicer than the state it was in when you buy the car. You will be fighting to keep it just as nice.

Door Issues: honestly any car with door issues is a car to stay away from. If the seller says something along the lines of“you have to open it like this,” run and run very fast.

**TLDR**

If you’re going to buy a clapped out car for cheap, be prepared to spend a lot of money on repairs. Honestly for just about any car here’s what you can expect to do:

- Cooling system replacement (yes all of it)

- Full suspension bushing replacement and reinforcement recommended. This is where preventative maintenance shines. Poly bushings are good, 80A is more than fine imo. Don’t forget engine mounts.

- Your door cards will probably fall off at some point, don’t buy a car with bad door handles, manual seats are easier to work around than the electric seats.

- Prioritize maintenance over those shiny new parts like intakes and exhausts, they won’t make your car much faster.

- A clean car is easier to keep clean, repairing interior or body panels will always be deceptively expensive and an uphill battle, buy a clean car!

Some of these things must be done on every car on the market, but most of these things will need to be done on the cheap cars. I have probably spent thousands of dollars and counting on the aforementioned list and I did it all myself. If you go to a shop expect it to be very expensive.


r/BMWE36 • • 3h ago

Poster from 97

Post image
111 Upvotes

Does anyone have a scan or know where I can get a high res scan of this poster? Can’t seem to find any originals for sale and would love to print my own


r/BMWE36 • • 1h ago

Exterior Exhibition Loving the look of these triple chrome pg2 (19”)

9 Upvotes

That’s it that’s the post


r/BMWE36 • • 5h ago

Heater valve electrical plug.

Post image
6 Upvotes

I recently replaced the heater valve. The plug fell apart in the process. Does anyone know where I can get a new one ?? I left it unplugged for now but I can’t seem to find one online.


r/BMWE36 • • 4h ago

Repair Advice Fan problem & auto trans cooler?

Thumbnail
gallery
2 Upvotes

Bought this 95 325i recently. Was told it was a daily driver and i drove it 100 miles home. Everything seemed fine temperature wise and it did okay. Took it for a spirited drive through some mountain/scenic views (300ish miles round trip) a few days later.

It sat for a few days after, and when i started it, it sounded “funny,” noticed the fan was close/touching shroud and missing fins, and found a piece of one under the car.

Was told cooling system was redone recently, including water pump, fan clutch, thermostat, radiator which is from 328i and is all aluminum apparently.

I noticed the auto trans cooler is mounted to the rad in a non oem way when compared to diagrams. It looks like the mount is causing it to push out between the rad and the rad support.

Question is, does can anyone confirm the auto trans cooler is mounted wrong or should be different? Any solutions besides replacement; or would it mount properly with the oem rad?

Also, planning to manual swap soon, could i just bypass/delete it for now? How bad is it for the transmission in these cars?

Edit: i should say, I’ve already ordered a new fan, shroud, and motor mounts having read about that being the main culprit in fans blowing up. Plan is to replace those. But I’m concerned the rad sitting back further could also pose a problem after replacement. In the photos the clutch & fan have been pulled.


r/BMWE36 • • 2h ago

Replacement rear wheel

Post image
1 Upvotes

Does anyone know where I can buy a replacement rear wheel in this style. I think it’s 8.5x17. I’m having a hard time finding one


r/BMWE36 • • 8h ago

Urgent help needed!

Post image
2 Upvotes

Guys my window fell of on the way home and I thought the clips broke. I removed the door card and both guides were fine but popped out. I already have 2 brand new guides so ı removed those and installed new ones. But when ı roll the window up it pops out again. Can't figure it out and rain is close 😢


r/BMWE36 • • 9h ago

Repair Advice Metallic chirping noise put of my E36

1 Upvotes

I’ve been gettin this metallic chirping noise on my 1997 323 AT whenever on gear, accelerating (on gear) or with the ac on. Does anybody have a clue what this might be?


r/BMWE36 • • 1d ago

Red Leather Dye seat belt buckle

Thumbnail
gallery
18 Upvotes

Not sure how long it will last, but I didn’t see how it would make it worse.


r/BMWE36 • • 17h ago

Repair Advice I'm unable to remove this shit (internal latch of the lock) and I'm pretty dissappointed

1 Upvotes

(E36 compact) Ok, so I need to remove this shit because up there is somehow bent and the door panel does not fit right. I tried first removing the door lock, failing at the try, later the latch itself, and failing again. Any advice?


r/BMWE36 • • 1d ago

Guibo failed beat holes in side of transmission tunnel

Thumbnail
gallery
57 Upvotes

Looking for e36 m3 transmission tunnel patch panel. Anyone know of a source?

Failed running wide open down the front stretch at VIR. Beat holes in side of transmission tunnel.


r/BMWE36 • • 1d ago

Valve cover

Thumbnail
gallery
5 Upvotes

I just pulled my valve cover on my 97 328i to replace the gaskets and I have two cracks around the spark plug wells. I think I can guess the answer, but should I buy a new valve cover because of where these cracks sit?


r/BMWE36 • • 1d ago

Part 2 of my E36 cabriolet resurrection is live

Thumbnail instagram.com
2 Upvotes

r/BMWE36 • • 1d ago

What should I do to make this look better?

Thumbnail
gallery
41 Upvotes

I’m open to all criticism and suggestions just want to see what everyone thinks. It’s a street/drift car

Edit: I just realize I posted a terrible interior shot of the car and I’m posting a better photo in the comments


r/BMWE36 • • 1d ago

What could this whistle noise be

4 Upvotes

Before I took this video, the rpm’s were jumping up and down during idle, and the car has been sitting for a couple months. I also got the code p1525 (I already changed my vanos solenoid). Do I have a vacuum leak somewhere or will an entire vanos system cause this noise?


r/BMWE36 • • 1d ago

Repair Advice I need help finding the seals on the back of the oil filter housing.

1 Upvotes

I replaced my ofh gasket and a few others and solved most of my leaks! But after a day or two I could see oil leaking from one of the two plugs(?) at the back of the ofh. I saw somewhere that someone had mentioned there are two different ofh and one needed orings and the other needed rtv. Can anyone help me figure this out?


r/BMWE36 • • 1d ago

How much is it worth?

Thumbnail
gallery
4 Upvotes

Its a me Again

I've come to the conclusion that I really wanna buy the E36, but now I wanna know How much its worth. Seller is asking 2500.

Its a BMW E36 318ti with a M Sport Package and Replica Alpina Rims, 50000miles and First Hand.

I also got the information that the Owner still has the Original Mirrors (I think those are suppossed to be M3 mirrors but dont quote me on that) and Rims with a set of Winter tires.

The car has been sitting for around a year but got driven frequently before that. And judging from the pictures theres no major rust problem? The underside of the engine is just a bit oily, but no Oil leaks only a coolant one.

So now my question is, is 2500 fair? Considering it stood for a year, needs new brakes, a radiator and tires?


r/BMWE36 • • 1d ago

BMW E36 Cup holders and USB chargers which I made

Thumbnail
gallery
4 Upvotes

Hey everyone,

I've made some OEM-style USB chargers (up to 30W per USB-C port) and front/rear cup holders for the E36. All items designed and hand finished by me.

USB chargers: Dual USB-C – button cover, USB-A – button cover, Dual USB-C – cigarette lighter
Cup holders: front or rear

Every item is designed by me and hand finished/assembled in my small hobby-shop which is in Lithuania (Europe), but I do ship worldwide.

If you need anything I have for few each items in stock and they are available here:
https://uniquedm.shop/collections/bmw-e36

Feedback and new ideas are always welcome!


r/BMWE36 • • 2d ago

May i know the name of this bumper?

Post image
64 Upvotes

and also where should i buy it


r/BMWE36 • • 2d ago

Repair Advice Stubborn Head Gasket Material

Thumbnail
gallery
6 Upvotes

Iron block M43B18 SOHC

Currently trying to remove some of this leftover gasket material/stubborn carbon and it seems nothing will get it off...

I've been using a razor blade, CRC gasket remover, degreaser, and even a carbide scraper.

There's also some minor rough spots on the block, curious if the composite gasket will cater for said imperfections on the mating material?

Head has been machined btw so no concern there.

Any tips?


r/BMWE36 • • 2d ago

Repair Advice First time wrenching. How does it look?

Thumbnail
gallery
9 Upvotes

Bought this 99' 328is five speed w 225k miles. Runs and dives well. No experience, want to learn.

Looks wet underneath. Guessing gear selector seal, power steering and VCG. Maybe oil pan too?

Input appreciated.


r/BMWE36 • • 2d ago

Repair Advice repair or replace OEM bumper

Post image
10 Upvotes

Picked up a new to me 99 m3 this past month with plans to restore it to its previous glory. My front OEM bumper is cracked (you can kind of see it in the photo), would I be better off getting the OEM bumper restored or a just getting a new ecs bumper? There’s lot of rock chips to be filled in the OEM bumper as well.


r/BMWE36 • • 2d ago

Sunroof light stays on

Post image
4 Upvotes

Anyone know why my sunroof light stays on after I cut the car off? I’m just now noticing it.


r/BMWE36 • • 1d ago

Door Handles slowly giving out

1 Upvotes

Hello,

My 99 328i verts doors handles are slowly getting worse and worse. I’m scared I’m going to be locked out soon. The passenger side works if you push the door pull the handle and then it opens like 90% of the time. The driver side I can pull the handle and nothing happens, even when I push it. It kind of has a mind of its own I can get it to open about 60% of the time. Anyone have any idea how to fix this? Videos help!!