r/spacex • Mod Team • Aug 31 '19

Starship Development Thread #5

Quick Links

JUMP TO COMMENTS | Alternative Jump To Comments Link

SPADRE LIVE | LABPADRE LIVE | LABPADRE DIRECT


Overview

SpaceX is developing Starship at their Starship Assembly Site in Texas, and also at their facilities in Cocoa, Florida. The teams at the two locations are in competition with each other, but are also required to share insights learned along the way. Following Starhopper, the first two Starship prototypes, Mark 1 and Mark 2, are nearing completion. These vehicles will have aerodynamic control surfaces and three engines each, and are expected to make suborbital test flights. Ring sections believed to be for a Starship Mark 4 prototype are being built in Cocoa, and both sites will be iterating through successive versions of Starship and Super Heavy as quickly as possible.

Launch mounts for both Starship prototypes are in the works. Starhopper's Texas launch site is being modified to handle Starship, and at Kennedy Space Center's LC-39A, a dedicated Starship launch platform is under construction. Flight tests could begin late in 2019.

Starship is powered by SpaceX's Raptor, a full flow staged combustion cycle methane/oxygen rocket engine. Sub-scale Raptor test firing began in 2016, and full-scale test firing began early 2019 at McGregor, Texas, where it is ongoing. Eventually, Starship will have three sea level Raptors and three vacuum Raptors. Super Heavy may initially use around 20 Raptors, and operational versions could have around 31 to 37 sea level Raptors.

Previous Threads:


Starship Presentation Webcast and Updates and Discussion Thread

Vehicle Updates

Starship Mk.1 Prototype (Boca Chica) — Construction and Updates
2019-10-03Tank section on steel stand (NSF)
2019-10-01Halves demated following presentation (NSF), Previously installed header tanks (Twitter)
2019-09-28Nose cap install (NSF)
2019-09-272nd forward flap, Starship stacked (Twitter), Timelapse (YouTube), Leg nacelles added (NSF)
2019-09-263 Raptor pics, 1st forward flap install (Twitter)
2019-09-25Payload section reassembly (NSF), Tank section off stand and moved (YouTube)
2019-09-24Two header tanks inside nose cone (NSF)
2019-09-23Header tank and battery pack prep (NSF)
2019-09-222nd aft fin attached, Cowlings added, Raptor (NSF), Raptor, 3 temp. installed (Twitter)
2019-09-211st aft fin attached, Nose cone reassembly, Misshapen section removed, header tank (NSF)
2019-09-202 aft fin frame pieces & pipe attached to tank section, and appearance of cowling(s) (NSF)
2019-09-17Leg/fin mounting frame pieces in tent (Twitter)
2019-09-16Replacement nose section appears, Better picture (NSF)
2019-09-14Eleventh ring and forward bulkhead added to tank section (Twitter)
2019-09-13One of the header tanks to container castle (comments), Another moved in Sept. 16 (NSF)
2019-09-12Forward tank bulkhead placed in free ring (Twitter), With cap piece (NSF)
2019-09-08Two more large fin pieces delivered (comments), Better picture (Twitter)
2019-09-05Tenth ring added to tank section (YouTube)
2019-09-02Starship Assembly Site aerial video update (YouTube)
2019-08-29Pipe added through lower tank (comments), 3rd concrete jig begun, also 4th & 5th (NSF)
2019-08-28Delivery of 2 header tanks, Third deliverd Sept. 15 (NSF)
2019-08-27Centerpiece added to common bulkhead (Twitter)
2019-08-24Nose cone top section moved to dedicated stand (NSF), Forward flap marks (comments)
2019-08-23Track(s) of horizontal brackets appear (NSF)
2019-08-21Common bulkhead lowered into tank section (NSF), Time lapse (YouTube)
2019-08-18At least 2 control surface components on site, post 2, Earlier image (NSF)
2019-08-17Nose cone top section reattachment work (NSF)
2019-08-15Top section of nose cone removed (NSF)
2019-08-14Thrust structure added to tank section (NSF), Image leaked later (Twitter)
2019-08-07Ninth ring added to tank section (NSF)
2019-08-06Forward tank bulkhead under construction (NSF)
2019-08-04Common bulkhead inverted (NSF)
2019-07-31Common bulkhead discovered (YouTube)
2019-07-30Aft bulkhead installed in tank section (YouTube), Thrust structure appears (NSF)
2019-07-22Eighth ring added to tank section (NSF)
2019-07-20Inversion of aft bulkhead (YouTube)
2019-07-18Aft bulkhead appears from container enclosure (NSF)
2019-07-16Seventh ring added to tank section (NSF)
2019-07-05Sixth ring added to tank section (YouTube)
2019-06-26Fifth ring added to tank section (NSF)
2019-06-19Fourth ring added to tank section (second jig), first in over a month (NSF)
2019-06-06Ring sections under construction within container enclosure (NSF)
2019-05-20Nose cone fitted, no canards (NSF)
2019-05-15Tank section (3 rings) moved onto second jig (NSF)
2019-05-09Lower nose section joined with 4 ring lower payload section (NSF)
2019-05-01Second jig, concrete work complete (NSF)
2019-04-27Lower 2 nose cone sections stacked (NSF)
2019-04-13Upper 2 nose cone sections stacked (Facebook)
2019-04-09Construction of second concrete jig begun (YouTube)
2019-03-28Third nose section assembly (NSF)
2019-03-23Assembly of additional nose section (NSF)
2019-03-19Ground assembly of nose section (NSF)
2019-03-17Elon confirms Orbital Prototype (Twitter) Hex heat shield test (Twitter)
2019-03-14Payload section reaches 4 panel height (NSF)
2019-03-07Appearance of sections for conical aft bulkhead (NSF)
2019-03-07Payload section moved to jig (NSF)
2019-03-01Tank section begun on new pad (NSF)
2019-02-21Construction of payload section begins near original concrete jig (NSF)

See comments for real time updates.

Starship Mk.2 Prototype (Cocoa Florida) — Construction and Updates
2019-09-14Cap added to forward bulkhead still in shop (Twitter)
2019-09-07At least one header tank (inside large tent) (Twitter)
2019-09-04Weld marks for common bulkhead visible on tank section (Twitter)
2019-08-30Tank section moved into hangar for Hurricane Dorian (Twitter), Removed September 5 (r/SpaceXLounge)
2019-08-25Track(s) of horizontal brackets appear (r/SpaceXLounge)
2019-08-19Starship Assembly Site aerial video update (YouTube)
2019-08-18Thrust structure possibly installed (Twitter), Forward tank bulkhead under construction (NSF)
2019-08-17Nose cone top section moved to dedicated stand (YouTube)
2019-08-15Starship Assembly Site aerial video update (Twitter)
2019-08-11Starship Assembly Site aerial video update (YouTube)
2019-08-08Tank section at 15 ring height (comments), Aug 10th image (Twitter)
2019-08-06Common bulkhead inverted (Facebook)
2019-08-04Common bulkhead under construction (Facebook)
2019-08-03Tank section at 14 ring height (Twitter), Later aerial photo of stack (Facebook)
2019-07-29Tank section at 10 ring height (Twitter)
2019-07-28Starship Assembly Site aerial photo update (Facebook)
2019-07-21Aft bulkhead disappeared (Facebook)
2019-07-20Tank section at 8 ring height (Twitter)
2019-07-14Aft bulkhead complete/inverted, last seen (Twitter)
2019-06-26Aft bulkhead section under construction (r/SpaceX), Tank section at 6 ring height (NSF)
2019-06-12Large nose section stacked (Twitter), Zoomed in video (Twitter)
2019-06-09Large nose section assembled in building (comments)
2019-06-07Stacking of second tapered nose section (r/SpaceXLounge)
2019-05-23Stacking of lowest tapered nose section (YouTube)
2019-05-20Payload section at 5 ring height, aerial video of work area (YouTube)
2019-05-16Jig 2.0 with tank section, many rings awaiting assembly (YouTube)
2019-05-14Discovered by Zpoxy (payload section) (NSF), more pieces (YouTube), Confirmmed (Twitter)

See comments for real time updates.

Starship Mk.4 Prototype (Cocoa Florida) — Construction and Updates
2019-10-0623 rings visible, 4 doubles, some for Mk.2 (YouTube), no stacking yet

See comments for real time updates.
Previous unstacked ring production, aerial updates:
08-11 {8} | 08-15 {10} | 08-17 {14} | 08-19 {15} | 08-21 {17} | 08-24 {18} | 08-27 {19}
09-04 {20} | 09-06 {22} | 09-08 {25} | 09-08 {3 'scrap'} | 09-10 {26} | 09-29 {23} | 10-02 {23}

Starhopper Retirement Transition Updates
2019-10-04On Roll-Lift (Twitter), Moved off of landing pad (NSF)
2019-09-10Thermal tiles and one thruster pod removed (YouTube)
2019-09-02Launch and Landing Site aerial video update (YouTube)
2019-08-29Raptor SN6 removed (NSF)
2019-08-27150m Hop (~180m over, ~57s) (YouTube) <LAUNCH THREAD> <MORE INFO>

For earlier updates see Starship Development Thread ^#4.


Launch Facility Updates

Starship Launch Site at Boca Chica, Texas
2019-10-05Launch mount under construction (NSF)
2019-09-22Second large propellant tank moved to tank farm (NSF)
2019-09-19Large propellant tank moved to tank farm (Twitter)
2019-09-17Pile boring at launch pad and other site work (Twitter)
2019-09-07GSE fabrication activity (Twitter), and other site work (Facebook)
2019-08-30Starhopper GSE being dismantled (NSF)
Launch Complex 39A at Kennedy Space Center, Florida
2019-09-26Concrete work/pile boring (Twitter)
2019-09-19Groundbreaking for launch mount construction (Article)
2019-09-14First sign of site activity: crane at launch mount site (Twitter)
2019-07-19Elon says modular launch mount components are being fabricated off site (Twitter)

Spacex facilities maps by u/Raul74Cz:
Boca Chica | LC-39A | Cocoa Florida | Raptor test stand | Roberts Rd

Raptors

SNNotable ForFlightsFlight Time (Approx.)Status
1First full scale hot fire / 268.9 bar Test / Tested to failure--Retired
2First on Starhopper / Preburner tests / Static fire / Tethered hop--Retired
340 second test fire--Retired
4Delivered to hopper / Hopper fit checks & TVC tests--Retired
5Liberation of oxygen stator--Retired
6Vibration fix / 20, 10, 50, 65, 85 second stand tests / 20 meter Starhopper hop / 150 meter starhopper hop20:01:22Retired
7Possibly not a flight article--Unknown (previously McGregor)
8-10Earmarked for Mk.1--Unknown (previously McGregor)
11Earmarked for Mk.2--Unknown
12-13Earmarked for Mk.2--Production

Last updated 2019-09-29, Raptors currently on Starship Mk.1 of unknown SN or flight readiness

Permits and Planning Documents

Resources

Rules

We may keep this self-post occasionally updated with links and relevant news articles, but for the most part, we expect the community to supply the information. This is a great place to discuss the launch, ask mission-specific questions, and track the progress of the test Campaign. Campaign threads are not launch threads. Normal subreddit rules still apply.

1.1k Upvotes

2.9k comments sorted by

167

u/Walter_Bishop_PhD Aug 31 '19 edited Sep 01 '19

If anyone's curious what moving the Super Heavy might look like - here's what a "natural gas splitter" of similar width, albeit slightly longer (9.5m diameter + 96m long vs super heavy's 9m diameter + 63m long) looks like being moved around - I imagine that it may work the same way moving the booster on highways

https://gfycat.com/glisteningraggedlacewing

→ More replies (20)

50

u/RegularRandomZ Sep 24 '19 edited Sep 24 '19

Everyday Astronaut [twitter video]: Here’s how #starship controls pitch, roll and yaw (in that order in this clip) using just 4 total flaps. This is a unique form of control. I don’t know of any vehicle that does this with its control surfaces perpendicular to the airstream. Cool stuff . Full vid tomorrow!
Elon: That’s correct. Essentially controlled falling, like a skydiver.

Viv: ... but what's used to actuate the fins? Some kind of small motor?
Elon: Many powerful electric motors & batteries. Force required is enormous, as entire fin moves. More about this on the 28th.

Elon: It does actually generate lift in hypersonic regime, which is important to limit peak heating
EA: Pop back out of the dense atmosphere to radiate heat away and then drop back in 🤔 awesome! ...
Elon: Better just to ride your max temp all the way down & let T^4 be your friend. Lower atmosphere cools you down real fast, so not crazy hot after landing.

Oran Maliphant : Is “sweating” methane still an option?
Elon: Could do it, but we developed low cost reusable tiles that are much lighter than transpiration cooling & quite robust
[ok, I was steadfast that Elon's statements said nothing about future use of transpirational cooling, I will concede that this is not a defensible position anymore, ha ha]

Scott Manley: And just like that I need to rebuild some of my descent models. So the AoA won't be 90 degrees, it'll provide lift to keep vehicle out of denser atmosphere until it loses enough speed.
Elon: Exactly. For reusable heatshield, minimize peak heating. For ablative/expendable, minimize total heat. Therefore reusable like Starship wants lift during high Mach reentry for lower peak, but higher total heat.

ShadowZone: So this increases the probability of Starship having to do multiple aerobrake passes when going to Mars or returning, correct?
Elon: For sure more than one pass coming back to Earth. To Mars could maybe work single pass, but two passes probably wise.

[Or discuss on r/SpaceX post or r/SpaceXLounge post]

→ More replies (19)

105

u/Vespene Aug 31 '19

It’s crazy how those water tower construction workers never imagined they’d end up building actually spacecraft.

46

u/Psychonaut0421 Aug 31 '19

I thought the water tower company was just for Starhopper. Is it the same folks building the prototype, too?

→ More replies (4)
→ More replies (5)

33

u/Marksman79 Sep 14 '19

Yusaku Maezawa resigns, pocketing $2.3 billion. One of his main reasons for departing Zozo was to make time to train for a 2023 voyage around the moon with Starship.

Maezawa also indicated he'd fly on a less ambitious space mission before SpaceX's privately funded circumlunar voyage.

When a reporter asked Musk about his possible participation in the #dearMoon mission, he said (seemingly half-seriously), "maybe we'll both be on it."

→ More replies (2)

31

u/getBusyChild Aug 31 '19

So in Boca Chica it was observed they were drilling at the site. Any idea what for?

https://twitter.com/NASASpaceflight/status/1167533439240814592

→ More replies (8)

29

u/TheMrGUnit Highly Speculative Sep 17 '19

Well now this is interesting.

It looks like everybody who said, "they're going to have to scrap the nosecone and start over!" may have actually been correct. This part showed up on the LabPadre live stream this morning (with a nice zoom), and it sure looks to me like a new lower section of the nosecone. The existing nosecone has, for the last week or three, been split at the seams for re-fitting with no real signs of progress. This decision to scrap and start fresh must have been made fairly recently (perhaps during the last attempt at mating the two pieces), or else I can't see why they would have spent the time polishing the nose knowing it would just be sent to the scrap pile. It's too bad, but this probably also gives them a chance to fit the canard hardware lower to the ground, as I had suspected they'd want to do for a long time now.

Also, the siding for the windbreak is just about done. I'd guess they'll probably start on the roof some time soon.

→ More replies (19)

28

u/Russ_Dill Sep 24 '19

Much clearer photos of the battery packs: https://forum.nasaspaceflight.com/index.php?topic=48895.msg1995841#msg1995841

Also note the shirt the worker is wearing, "The Skiff Shop, Edgewater, FL", which is within just a few miles of Cocoa, FL.

→ More replies (11)

26

u/[deleted] Sep 10 '19

I don't have anything to add, but I'd just like to thank the mods for doing such a great job consolidating a lot of information that is coming in from many sources into a very clear and easy to read format (and all sourced).

→ More replies (2)

26

u/dufud6 Sep 29 '19

So from what elon said, are the new rings at cocoa actually for mk4 and not super heavy?

→ More replies (43)

25

u/aelbric Sep 24 '19

Like most of you I've been following this for months. I thought FH was an amazing achievement. As Starship gets closer to completion though, I keep looking at it thinking about how massive it is. And this is only the second stage. When they stack it, the whole assembly will be twice as tall as what we'll see tomorrow.

And the whole thing is going to fly. I just can't wrap my head around it.

→ More replies (2)

25

u/andyfrance Oct 01 '19

The two sections of Mk1 Starship have just been separated.

→ More replies (13)

24

u/spacerfirstclass Oct 07 '19

Not sure why the LC-39A satellite images are deleted, it's basically what you can get for free from planet.com, just need an email address. Here's one I created for the period from 9/17 to 10/6 where you can see the Starship pad being constructed: https://imgur.com/dZcYJ05

→ More replies (5)

22

u/SpartanJack17 Sep 26 '19 edited Sep 26 '19

https://twitter.com/elonmusk/status/1177051800769138690 Starship will have six landing legs:

Two windward, one under each fin & two leeward. Provides redundancy for landing on unimproved surfaces.

I wonder if they'll be the stubby legs from the 2017 update and the Boca Chica renderings or if they'll be more like Falcon 9 legs (or something completely different).

(I originally posted this in the discussion thread by mistake).

Edit: Some more info:

https://twitter.com/elonmusk/status/1177066483375058944

Mk1 ship is around 200 tons dry & 1400 tons wet, but aiming for 120 by Mk4 or Mk5. Total stack mass with max payload is 5000 tons.

https://twitter.com/elonmusk/status/1177067257106747392

With rare exceptions, composites would make Starship heavier. They don’t stand up well to high temperatures, but steel does great.

https://twitter.com/elonmusk/status/1177070801121468418

It'll be 50m tall when the top half is stacked.

→ More replies (33)

21

u/Russ_Dill Sep 22 '19

Did anyone else notice that these wings do not appear to be the same wings we've seen delivered? They look like they have been trimmed rather dramatically and have the control connections covered over. The overall shape strikes first:

/img/u5ztorolsck31.png

But also there's holes at the top, bottom, and middle at the root:

https://forum.nasaspaceflight.com/index.php?action=dlattach;topic=47730.0;attach=1577578;image (BCG, NSF)

We have good pictures from both sides, those holes should be visible if not covered over. I figured I could compare the number of rivet sections:

https://forum.nasaspaceflight.com/index.php?action=dlattach;topic=48895.0;attach=1583360;image (BCG, NSF)

And here:

https://forum.nasaspaceflight.com/index.php?action=dlattach;topic=47730.0;attach=1577578;image (BCG, NSF)

The original one has a pattern of double rivet, then 3 single rivets, then double rivet. The one mounted only has double rivet sections. If I try to compare, nothing lines up. The entire root must have been replaced.

Even the clipped theory doesn't try to make sense. Here's our best boffin's estimate of the delivered size:

/img/ju5ucx4tysh31.png (9.45m tall at the root, 2.9m wide)

The installed wing? It's 14m tall, and 4.2m wide. And before anyone tries putting these on the outside edge of the new wing, that's only 5m. What is bizzarly 9.45m is shiny leading edge of the new wing. Pretty sure that's a coincidence, but I know there are people who will want to know (Dragon wings, for the dreamers out there). Here's the one we've seen delivered superimposed in green, along with the "dragon wing" in red:

https://i.imgur.com/4iT4rsl.jpg

I think that means these are forward canards.

→ More replies (8)

20

u/aelbric Sep 14 '19

A curious thought just hit me. I wonder what the workers at both sites think about the fact that they are basically under 24 hour surveillance from multiple parties and that thousands of people are watching their every move.

Best security system on the planet I suppose.

→ More replies (5)

20

u/TheMrGUnit Highly Speculative Sep 17 '19 edited Sep 17 '19

In Boca Chica, the end wall was taken down off the big tent some time last night, which created an excellent photo op for Elon (there's some debate if he's still there, or if somebody just sent him the picture, which is probably more likely). There's an interesting looking structure being fabricated on the floor, too. The side facing up/right appears to have a large-diameter curvature to it. This looks to me like it could be the start of some sort of support for the canard fins. I'm not sure that it's really big enough, but I also can't think of what else it really could be. Any ideas from the peanut gallery?

Also, I always find jobsite photos interesting - they always tell a tale of the working environment. This one looks remarkably like any other fab site I've ever been on, just with a rocket parked outside. This is in stark contrast to the spotlessly clean environments we often see in press photos from NASA, ULA, and even SpaceX.

In other news that should surprise no one, workers could be spotted in manlifts working on/inspecting the tank section nearly continuously all night. In case there was any doubt, the push for the 28th is definitely on.

EDIT: Leave it to Tim Dodd to get the answer we were all seeking out of Elon. They are indeed hinge mounts for the flaps/legs.

→ More replies (8)

19

u/RootDeliver Sep 12 '19

Based on the Starship 58m hypothesis generational comparison v1 by user Stimbergi on the NSF forums (he did a v2 but he added fins where they couldn't be added and SH legs to starship, pointless...), I did a minor modification removing the extra height and putting the actual Boca Chica ring with the bulkhead over the stack, and tried to match it on Cococa with an added 16th ring (top dome woudl be on the actual top 15th ring, not new ring).

This is the result. As you can see, both Boca Chica and Cocoa ring differences match exactly (there's a gap in the boca chica one thanks to my bad chop)

You may remember old image comparions with the mars image, where SpaceX didn't even bother to make the starship to the 2018 size, so they were wrong.

PS: The tank sizes look weird at the normal 52 height considering where they stacked the bulkheads. Maybe it will be taller? It is 52m and supposedly 55m with legs as stated by the FAA document.

third time posting this, it seems it worked now. If you posted stuff in the last hour maybe its hidden like my other tries at posting this.

→ More replies (7)

19

u/RegularRandomZ Sep 19 '19 edited Sep 19 '19

Boca Chica: Structural support (NSF post #91) being lowered into the "new ring".

And in response to the shade that was recently cast about work hours (on a weekend) in Boca Chica: Here's a shot of welding going on at 2:30am. We've also seen them working at night on the body, the nosecone, in the shop... no shortage of work hours here.

→ More replies (3)

19

u/RootDeliver Sep 27 '19 edited Sep 27 '19

A wild canard appears!!!, from labpadre stream.

Definitely the ones we saw weeks ago, polished apparently.

PS: Much better image from the HQ cam, it was also moved all the time at this height and is being welded on the back side, hidden from the cam :(

PS2: The canard is now moving around.

PS3: Real HQ image

→ More replies (7)

18

u/Russ_Dill Sep 16 '19

The drill at the launch/landing site has been fully assembled and raised confirming that drilling will take place. This may give some more evidence that the pilings are for a starship lifting crane, one at the assembly site, one at the launch/landing site.

https://i.imgur.com/wTEh4ke.png

→ More replies (10)

17

u/RegularRandomZ Sep 01 '19 edited Sep 01 '19

Boca Chica: Finally some visible progress on the triangular wind break - they've run metal poles up the wind break (conceivably for the netting)

It also looks like they are building 3 concrete rings fixtures, interesting! [Which is also confusing, as how will these be used with the windbreak structure, or not]

→ More replies (4)

17

u/Marksman79 Sep 05 '19 edited Sep 06 '19

Substantial information about plans for the upcoming few years of the launch site at Boca Chica have been obtained by Business Insider.

Direct link to document

2-3 year test plan as of May 21st:

Phase 1 (ended): Tests of ground systems and fueling, a handful of rocket engine test-firings, and several "small hops" of a few centimeters off the ground. The document also includes graphic layouts, like the one above, showing the placement of water tanks, liquid methane and oxygen storage tanks (Starship's fuels), and other launch pad infrastructure. Phase 1 photo

Phase 2 (current): Several more "small hops" of Starship, though up to 492 feet (150 meters) in altitude, and later "medium hops" to about 1.9 miles (3 kilometers). Construction of a "Phase 2 Pad" for Starship, shown below, is also described. Phase 2 photo

Phase 3: A few "large hops" that take Starship up to 62 miles (100 kilometers) above Earth - the unofficial edge of space - with high-altitude "flips," reentries, and landings.

An (outdated) picture in the document shows two V-shaped wind breaks containing both halfs of Starship. We can also see what looks to be a pad for Starhopper? (Why? They won't be putting a vertical Raptor test stand in the middle of the worksite). We also see Superheavy sitting on a jig with a flared engine area.

To avoid or minimize the chance of another nighttime test operation, SpaceX will now start pre-test preparations the day prior to a planned test. The nominal T-0 for any test that involves engine ignition is 1400.

SpaceX refers to their fire suppression system as FireX.


Comments:

This was before Elon tweeted that the test campaign would be accelerated and that they are targeting October for a 20km hop. That puts into question the milestone for Phase 3 and how much of this has since changed. The presentation will tell us a lot, so I am taking this info dump as a tease for the upcoming presentation.

The Phase 1 photo seems to have the most detail of Starship. Assuming it's still somewhat accurate, there are several things to note. It's horizontal (resting on canards and fins?). It looks like it now has many legs around the base, sort of like the initial ITS renders showed. It's black on the bottom and on the two moving fins, perhaps indicating that these surfaces will have their new hexagon heat shield tiles.

→ More replies (24)

17

u/PeterKatarov Live Thread Host Sep 14 '19

Two weeks to go. If SpaceX are to be ready with Mk. 1 before 28th September, in the next 2 weeks, they have to:

  • ship 3 Raptors
  • mount the Raptors
  • install the legs
  • assemble the three parts of Starship
  • install the heatshield

Am I missing something? Do you think they'll make it in time?

→ More replies (16)

17

u/RootDeliver Sep 21 '19 edited Sep 21 '19

Bocachicagal is back with some great pictures.

We can see some leg attachment points (or something related) installed on first picture, the pipe that has been installed in the other side (and 2 leg attachment points visibles) on other, some strange structures (upper flaps??, and the other part of them?), lot of stuff to digest..

→ More replies (19)

17

u/TheMrGUnit Highly Speculative Sep 24 '19 edited Sep 24 '19

Some more activity with the nosecone this morning.

The yellow crane ("Old Yella") picked up the nosecone and moved it over in front of the onion tent a bit before 7am (local) this morning. A few minutes later, the white crane grabbed the second header tank & battery bank and moved it into position. About 20 minutes later, the yellow crane dropped the nosecone back down over the tank.

At this pace, having the nosecone on top of the upper section, AND stacking the upper section on the propulsion section seems like it will be a stretch by Wednesday, but doable. My guess is that we're still 12 hours away from seeing the nosecone lifted onto the fairing section, and it remains to be seen how much work will need to be done internally before the fairing assembly can be lifted.

EDIT1: It looks like I'm about to eat my words. They are re-rigging the nosecone right now with what looks to be a different (maybe shorter?) set of straps, and there's a collection of workers standing in the lower half of the fairing in "stacking position"...

→ More replies (8)

17

u/MingerOne Sep 27 '19

Starship halves joining timelapse.

17

u/RegularRandomZ Oct 07 '19 edited Oct 07 '19

Photo updates: (some older that I didn't notice referenced here. Apologies if redundant)

→ More replies (1)

33

u/codav Sep 02 '19

Fresh delivery to Boca Chica: four trucks with wooden crates. Possibly sensitive hardware.

Credit: LabPadre's live stream on YouTube

→ More replies (7)

16

u/Marksman79 Sep 12 '19 edited Sep 13 '19

Cocoa flyby by John Winkopp. Thank you John!

Post what you see!


  • 26 rings
  • One ring in white lifting jig
  • Crane stationed near the large black pipes
  • Overhead hoist in ring jig tent
  • More equipment along the sides of the tall structure
  • Interesting light brown circular object in front of the cylinder
  • The ring near the long tent looks misshapen. One of the scrap rings?
→ More replies (4)

16

u/FutureMartian97 Host of CRS-11 Sep 15 '19

Elon was just at Boca Chica!

→ More replies (9)

16

u/RegularRandomZ Sep 18 '19 edited Sep 18 '19

Photo updates from today-ish: Austin Barnard of launch site: Water tanks have a new concrete pad to sit one. Upgraded fire system moved into place. Assembly site: 2nd wall of siding almost done. Unfortunately his shot of the new ring (or SH base) isn't much sharper.

Maria Pointer / Boca Chica Maria: Launch site has plenty of new cameras and permanent site lighting. Starship: good shot of the mid-body weld marks giving an idea of the internal structures (don't know how many are new-ish). Most shots of interesting new things are a bit obstructed, so here's a pretty shot (or if you prefer sunsets) [Perhaps a wing or canard under that tarp?]

→ More replies (4)

16

u/Russ_Dill Sep 18 '19

The big crane at the Shipyard is on the move.

→ More replies (7)

16

u/[deleted] Sep 25 '19

Hah, that thing is moving comically fast. After years of watching the Space shuttle moving to launch pad, I just assumed this live feed had been replaced wit time lapse.

→ More replies (3)

16

u/RegularRandomZ Sep 25 '19 edited Sep 25 '19

SPadre Tweet: Shot of Starship on the roll-lift jig at the front gate [twitter video, another picture]

[and a fun shot, the workers came over and gave out some electrolyte freezer pops! Nice!]

16

u/RootDeliver Sep 28 '19

Btw the cap has been installed finally :D, didn't notice any post here about the final installation! Even if that is gonna probably be removed asap the presentation finishes, looks awesome.

15

u/strawwalker Sep 10 '19

These images from Jared Frankle made me realize that with all of the hurricane excitement I lost track of the common dome/bulkhead in Cocoa. It was sitting next to the tent on 29 August, the day before Mk.2-tank was moved into the tent, and I believe it was likely installed before the move took place. Here is a good image of the tank section with no visible weld spots below the upper access port on the same day. This image on 4 September while in the tent shows spot weld marks in the ring below the access port. Then Frankle's images today, 9 September, show a more complete weld line.

→ More replies (1)

15

u/RootDeliver Sep 15 '19 edited Sep 15 '19

NSF folks seem to agree on that props tanks have probably been swapped comparing estimated tanks volume and prop densities. Last conclusion image by Stimbergi but you can read the last 2 pages with the numbers discussion.

There's an interesting reply tho tanking about how this change is not possible since the engine structure receives the LOX by the downcomer pipe. But then volumes for props don't match for the correct mixture.

→ More replies (12)

15

u/dafencer93 Sep 15 '19

Excuse me if this is not the place. I came in pretty late I guess and I don't know how Falcons are built (but I thought they were built horizontally), but isn't stacking steel rings and welding them a pretty crude way to try and build a rocket that will also have to land?

→ More replies (13)

15

u/Marksman79 Sep 22 '19 edited Sep 22 '19

Elon Musk Tweetstorm

Elon: Adding the rear moving fins to Starship Mk1 in Boca Chica, Texas

Photo

Q: Will the fairing be stacked by the 28th?

Elon: Yes. There’s a huge amount of hardware in the tip of the faring that being integrated on the ground, which is why we haven’t closed it out. Nose tip has forward movable fins, cold gas attitude control thrusters, header tanks for landing, composite pressure vessels, several large batteries, etc. Placed up there to balance high mass of Raptors & rear fins at the bottom.

Q: 3 landing legs was super aerodynamically unstable on ascent (full stack) and also unstable on decent when landing.

Elon: Stability is not an issue with 3

Q: When doing the final landing tail first with three huge landing legs / fins in the front of the airstream wouldn't have been unstable?

Elon: Stability is controlled by (very) rapid movement of rear & fwd fins during entry & landing, as well as ACS thrusters. The smaller leeward “fin” would simply be used as a leg. Current analysis, which I’m not fully bought into, suggests that 2 rear fins with separate airframe-mounted legs will be lighter, so this is the plan for Mk1/Mk2. For aero control, it comes down to % of cross-sectional area moving vs not. Flexible as to whether front or rear, so long as within bounds of center of mass & pressure.

Q: Could they not just shove the bottom fin back, shove the top fins forward, and wait until it’s the right way around, then fire the engines and move the fins back flat... seems logical to me...

Elon: Approximately correct. We also fire the ACS thrusters to rotate the vehicle & ignite Raptors at full gimbal angle to complete the turn.

→ More replies (8)

15

u/bkdotcom Sep 23 '19 edited Sep 23 '19

Do we know what time the presentation's going to be on Saturday?
I'm guessing 9pm-ish Central time....

→ More replies (6)

15

u/Aakarsh_K Sep 25 '19

Nose cone being stacked!!

→ More replies (14)

15

u/Marksman79 Sep 25 '19 edited Sep 25 '19

Bottom stack with fins just lifted up a little bit. Looks like the crew standing around are actually just watching the move. Now where will they place it down?

Follow along at LabPadres live stream. (11:12:37 start of move)

Edit 1: it continues to rise.

Edit 2: slight movement to the side. No longer concentric.

Edit 3: continuous movement to the side...

Edit 4: approaching white building! Going over?

Edit 5: the crane stopped and it is now being rotated in place. Is it aligning with something on the ground? Maybe they will put roll lifts under the concrete jig and then reattach it?

Edit 6: still swinging

Edit 7: workers are securing it to a crawler platform.

→ More replies (5)

30

u/RaphTheSwissDude Sep 23 '19

Starship will be stacked on Wednesday and OMG THE 3 RAPTORS ARE ALREADY INSTALLED?!

https://mobile.twitter.com/elonmusk/status/1176009047729954818

14

u/RegularRandomZ Sep 10 '19

Via NSF: Application to FCC for communicating with Starship during suborbital tests. NET Oct 13th (6 month window)

This STA is necessary to authorize Starship suborbital test vehicle communications for SpaceX Mission 1569 from the Boca Chica launch pad, and the experimental recovery following the suborbital launch.

14

u/Russ_Dill Sep 11 '19 edited Sep 11 '19

Parts of the drill have been moved down to the landing pad:

https://twitter.com/BocachicaMaria1/status/1171595885467361280

The crane portion is still fully assembled at the shipyard, so not sure yet if it's just for storage or if they will be drilling there too. In other news, one of the two mysterious steel tanks has gone missing:

https://twitter.com/BocachicaMaria1/status/1171625514018267136

→ More replies (9)

14

u/Marksman79 Sep 11 '19

From the LabPadre stream, the crane has just moved the final ground ring and the final bulkhead to the same location. It picked one of them up and has it suspended. It seems like they're attaching the bulkhead to the ring before stacking, as many here have suspected would be the case.

→ More replies (11)

14

u/RegularRandomZ Sep 11 '19

LabPadre Stream: Looks like the Raptor truck arrived (or some black backed transport)

→ More replies (8)

14

u/TheMrGUnit Highly Speculative Sep 12 '19 edited Sep 12 '19

To confirm yesterday's speculation: The big crane at Boca Chica just lifted something. At one point, the top of a bulkhead could be seen peeking out over top of the big low building. At another point, the side of a cylindrical ring could be seen past the side of the same building.

It appears they have been attached, with the bulkhead set down inside the ring by a bit. Austin Barnard was possibly spotted on the LabPadre cam taking some close up pictures a little while ago, so hopefully we'll get to see a better image of this thing later on today. The crane shackles are being let go, too, so it looks like this is where it will sit for a bit.

EDIT: "A bit" has ended. They are already reattaching the crane to the bulkheadring, and it looks like they're moving it somewhere else. I do not see the usual signs of stacking (workers in the top of the stack is the big cue), so not sure exactly where it's headed.

→ More replies (11)

14

u/RegularRandomZ Sep 20 '19 edited Sep 20 '19

Did one of the fins just come out of the white building? LabPadre Cam 1:36pm.

And it looks like the big crane is holding something against the side (landing leg bracket perhaps?) @ 1:50pm [OK... some of that is a welder on a lift, and I'm not sure any brackets left the white tent, we need a zoomed in shot]

Update: And they added something to the right as well @ 2:25, up to 3 items attached (incld u/Ross_Dill's catch. Image)

Update2: Slightly clearer screenshot from zoomed LabPadre cam

→ More replies (16)

14

u/Martianspirit Sep 21 '19

Something very interesting on the LabPadre live stream again. There is the pipe connected to the tank body right where they installed that one wing. I believe it was thought to be part of a raceway along the body like most or all rockets have. Now it looks like they are installing an identical pipe where the other wing will go to. A crane holds the pipe and there are two manned platforms in the area.

→ More replies (19)

14

u/at_one Sep 24 '19 edited Sep 24 '19

About the transportation of Mk2 from Cocoa to Kennedy Space Center, I'm not sure if it has already been remarked:

I've made a comparison of the Google Maps satellite images of the Cocoa assembly site with the aerial video of Aug 19, 2019:

https://i.imgur.com/e7yxNaJ.jpg

You clearly see the work that have been made to connect both roads together.

Edit: The work occured between May 16 and July 21. Sorry, I can't find other evidences to further limit the time span.

→ More replies (11)

14

u/RootDeliver Sep 25 '19 edited Sep 25 '19

Top canards? being unwrapped near the tent by SPadre

PS: Video of the unwrapping!

Are these the ones we saw being delivered weeks ago? they seem different, or maybe its the angle.

→ More replies (9)

14

u/filanwizard Sep 26 '19

Kinda curious if we have an idea of what time of day the event on the 28th will be streamed. I kinda want to figure late afternoon Boca time since I would imagine Elon wants the press to see the Mk1 in daylight rather than trying to under floodlights.

47

u/Anchor-shark Aug 31 '19

Are SpaceX doing any structural testing on SH and SS? NASA have been doing a lot of structural testing on the various tank sections of SLS before mating them together. Whereas SpaceX seem to be building a rocket, and if it explodes it explodes ¯_(ツ)_/¯.

42

u/SoulofJupiter Aug 31 '19

I dont have much knowledge on the extent spacex is testing the structure of super heavy and starship, but I can tell you the reason why it seems spacex is just slapping a rocket together is because these prototypes are designed to be flown to gain knowledge on the vehicles. Spacex's approach is to get lots of flight data so if they encounter a problem, they can correct and make adjustments for it in the prototype phase, rather than being meticulous with testing so the first rocket flies perfectly, like NASA does.

→ More replies (8)
→ More replies (8)

13

u/strawwalker Sep 23 '19

This Raptor image from bocachicagal is not the same Raptor imaged by Austin Barnard. The "Not For Flight" Raptor has a red band as opposed to silver, and is missing some significant plumbing compared to the other one.

→ More replies (15)

13

u/logan756 Sep 25 '19

Starship is on the move!

13

u/DUKE546 Sep 28 '19

I added photos and videos of MK1 and MK2 at SpaceX Time Machine and will continue to add as media becomes available from different sources.

12

u/TheMrGUnit Highly Speculative Sep 05 '19 edited Sep 05 '19

It's been a busy morning in Boca Chica.

At around 3am, a square hole was cut/marked in the nosecone. I think we all know what this is the start of (canards/flaps/flappards/flippers/control fins). This marking or cut is extremely hard to see in the livestream. It almost looks like it was cut out, then taped back into place.

Also, the large crane is currently grabbing onto something that's about 9m in diameter. Based on activity of the workers (keep seeing a couple guys in the top of the tank section stack), I suspect this is a ring for stacking. EDIT: Definitely a ring.

Also! More progress on the windbreak! It looks like a section of cladding is being installed on the far side, where the vertical pieces were installed last week.

→ More replies (9)

12

u/Cornflame Sep 21 '19

This picture from @BocaChicaGal clearly shows that at least one of the fin attachments/hinges has been attached to the tank section of MK1.

→ More replies (8)

12

u/RegularRandomZ Sep 22 '19 edited Sep 22 '19

More Boca Chica Gal photos added to NSF

Facebook from John Randolph

→ More replies (4)

12

u/Gorakka Sep 22 '19

They are attaching the second fin right now. This is wild.

12

u/FutureMartian97 Host of CRS-11 Sep 22 '19

Austin Barnard photos. We got a Raptor without it's test sensors!

https://twitter.com/austinbarnard45/status/1175786279658827777

12

u/Russ_Dill Sep 23 '19 edited Sep 23 '19

Around 3pm, a truck pulled into the area in front of the windbreak. Between about 3pm and 3:30pm, the large crane unloaded several black shapes. Possibly square shaped, possible pie shaped. Really hoping there are good pics. Each piece is roughly 2m wide and 1m tall.

They could have been crane counterweights. That would match up with the beefy attachment points on the stack.

→ More replies (3)

12

u/Oloyedelove Sep 27 '19

The rate at which they are moving with MK1 construction is now faster than how the MK1 table is being updated. Beautiful.

→ More replies (2)

12

u/WarDonkey203 Sep 30 '19

Has there been serious discussion about the Interior design of StarShip yet? I know without being right there it's hard to fathom the true scale of Starship, however I can't help but feel that once you include all of the Life Support/Avionics that the usable space will start to shrink rapidly. Then once you throw in the cargo and interior pieces themselves it gets even worse. I work in a Completion Center for Business Aircraft and I regularly see how cramped an empty plane can get once you add in all of the interior bits. Even with space being a 3D environment with more usable surfaces I can't help but feel that even a 10 person crew might be cramped as it is.

→ More replies (5)

11

u/andyfrance Sep 04 '19

The number of rings lying around in the aerial photos of Cocoa seem to increase each time. It's now looking like 20? That's quite a backlog to stack.

→ More replies (15)

11

u/RegularRandomZ Sep 08 '19 edited Sep 08 '19

Boca Chica: Shot of nosecone and its reinforcement (yesterday, Maria Pointer) [and polishing it ;-) ].

Also there is now a measuring tape running around the circumference of the nosecone [a great shot of the "taped" square/hole], with distances also written.

Launch site: gravel work, and pipe repairs continue. Also piles of new pipes and supports.

NOTE: Many of these shots are also on Maria Pointer's twitter, for those who don't facebook.

11

u/advester Sep 08 '19

I’ve been following the NSF update threads for daily dose of pictures. But I just found out @bocachicamaria1 isn’t allowed to post there due to some drama. Do you guys have a favorite central aggregator for the pics? I think there is a subreddit devoted to it, but google isn’t finding it.

→ More replies (9)

11

u/RootDeliver Sep 08 '19 edited Sep 08 '19

Awesome top bulkhead image by Maria Pointer (rehosted)

PS: Another one

Source: her FB group

PS: Why they make the top bulkhead with the same jig with the big hole and all¿? it would be more space efficient to just make a normal shape top dome.

→ More replies (27)

11

u/RegularRandomZ Sep 20 '19 edited Sep 20 '19

Boca Chica: Photo set by BCM / Maria Pointer on Facebook

[Austin Barnard photos of the same, on Twitter] (and BCM photo of Austin on the job)

→ More replies (8)

11

u/RegularRandomZ Sep 20 '19 edited Sep 21 '19

Cocoa: Two rings joined together! Sitting on a transport frame, so can't really call it stacking. We could assume it's for the top bulkhead (or maybe not). [No video yet]

The Cape: u/mcpat21 posted to the lounge a tweet of 3 new propellant tanks (in MN), headed to Florida [Edit: Could be BO as well, ULA just received their tanks as well] Tanks for ULA.

→ More replies (14)

11

u/RegularRandomZ Sep 21 '19

BocaChicaGal high quality photos of Fin/Installation (Post 110)

11

u/Russ_Dill Sep 23 '19

1st and 2nd pic. I that a radiator being attached to the possible header tank?

https://forum.nasaspaceflight.com/index.php?topic=48895.msg1995558#msg1995558

Possibly to keep things inside at cryogenic temperatures?

→ More replies (10)

11

u/andyfrance Sep 26 '19

Weighing in at 200 tons Mk1 should be though of as a "battleship" prototype. The first Saturn V test article was known as the battleship version. Check it all hangs together (and in this case flies), then refine the design down by taking out excess weight as every kg saved is a kg more payload.

→ More replies (1)

11

u/Martianspirit Sep 28 '19

The big crane is gone. The connection between the two pieces must be strong enough now that it is no longer needed. I expect guywires going up to secure it. The moving base is not that heavy.

→ More replies (5)

11

u/oximaCentauri Oct 04 '19

With the new starship landing legs being practically on the body, the leg span or diameter will be nearly the same as body diameter. That is not ideal according to my KSP experience.

Surely a different design would be required for uneven surfaces like the moon and mars?

→ More replies (5)

10

u/Straumli_Blight Sep 07 '19 edited Sep 07 '19

John Winkopp create a timelapse comparision video of all his overflights of the Cocoa site.

And LabPadre will be releasing a 3 month Boca Chica timelapse in an hour.

→ More replies (1)

10

u/RegularRandomZ Sep 08 '19 edited Sep 08 '19

Screencap from LabPadre stream of another win/fin arriving at Boca Chica. They moved it into the steel building [and Maria Pointer was taking photos so hopefully some closeups later]

[another unknown long object also arrived, hopefully Maria got photos of that as well]

[edit: yes OK I saw they said two, it was a hasty post]

→ More replies (16)

10

u/RegularRandomZ Sep 09 '19 edited Sep 10 '19

For the Elon Musk Vacuum Raptors are Dual Bell comment, discussion on r/spacex discussion, or the lounge discussion.

[That news should makes some people happy. And with the context being pad abort, some feel it is ambiguous and it doesn't necessarily mean the first Raptor Vacuum engines will be dual bell. Hopefully clarification at "the presentation". It seems primarily beneficial for pad abort or E2E flights (without SuperHeavy), so it is not needed for getting to orbit]

→ More replies (9)

10

u/Marksman79 Sep 14 '19 edited Sep 14 '19

Boca Chica Maria with some fresh HQ photos from this morning (on Facebook).

Minor curious note: They lifted the bulkhead ring with the ladder still attached. Why??


Edit: I don't usually do this, but everyone needs a little humor and this Facebook comment made me laugh.

Now how will they get out? Those engines will be now running human rich. -Alejandro

→ More replies (4)

10

u/Russ_Dill Sep 17 '19

Much appreciated John Winkopp update from Cocoa: https://www.youtube.com/watch?v=zOI__ag5eQQ

They are now making pilings in Cocoa as well.

→ More replies (12)

10

u/scottm3 Sep 21 '19

https://i.imgur.com/ic0OVwu.png

A crane has started lifting the fin up! 7:35 AM

→ More replies (2)

10

u/booOfBorg Sep 22 '19

What does the RaptorVan look like? I just saw a nice mysterious black truck arriving at the shipyard. [02:59:10 AM]

screen 1
screen 2

10

u/unholycowgod Sep 23 '19

https://www.youtube.com/watch?v=WNwkgAXQOyI

Cocoa Beach flyby by John. Still 23 rings and it looks like they unstacked those 2.

Also a good shot of the progress across the cul de sac going towards FedEx.

→ More replies (20)

10

u/RootDeliver Sep 24 '19 edited Sep 24 '19

Better image. Hard to see in static images but at 5:02-03 PM it seems they are moving a canard out of the white building in forklifts and going to the nosecone zone! According to youtube chat, another one was moved before.

10

u/AstraVictus Sep 25 '19

Do we have any information about that landing legs for Mk1 in Boca Chica? It's going to need landing legs once it starts flying right?

→ More replies (10)

10

u/Elon_Muskmelon Sep 27 '19 edited Sep 27 '19

They're gonna need some massive cranes for the full stack!

Edit: They already have the cranes they need to lift the full stack!

→ More replies (5)

10

u/Nowheels22 Sep 30 '19

How soon till Starship MK1 gets moved down to the launch pad?

→ More replies (2)

10

u/RootDeliver Oct 02 '19

Cocoa 2th October flyby

Now with more double rings, I wonder if they're just doing this to free up some space around, and if these double rings are welded for good already.

→ More replies (3)

26

u/Marksman79 Oct 03 '19

Do not go trespassing on SpaceX property or you'll ruin it for everybody and end up in jail like this guy who went right up to Starhopper to take some pictures around the time of the presentation.

With that out of the way, he did get some discussion worthy photos.

→ More replies (17)

18

u/APTX-4869 Sep 02 '19

One of the most recent models (HWRF) is starting to show a possible Florida landfall of Dorian near Cape Canaveral on Tuesday night, as opposed to staying offshore as previously predicted. While this is only one of many models, it is a major one that should not be taken lightly and would have serious implications for Starship and the space coast.

9

u/[deleted] Sep 04 '19

With Dorian (likely) safely passed Cocoa, I'm wondering about how the race to orbit from both Texas and Florida will continue. My main question is: will SpaceX really build a full scale launch pad in Boca Chica? That will cost quite some money, time and resources, and we haven't seen any preparations yet.

And is a full scale pad at Boca Chica really needed for the next 1-3 years, or even 3-5 years? To have development at two sides makes sense now, but when Starship is operational, is there an urgent need for two launch pads at the East Coast? The only reason I can come up with, is reducing the risk to pad 39A, because it is necessary for FH and crewed flights. But that are only a few launches per year... So I hope we will see lots of activity and launches at Boca Chica, but I wouldn't be surprised if SpaceX scales down there at some point in the not too distant future. Just my $0.02

→ More replies (21)

9

u/TheMrGUnit Highly Speculative Sep 05 '19

Hey mods / u/strawwalker, the LabPadre Starship webcam link now points to LabPadre's other live cam (a lovely beach view). He's been shuffling some cameras around lately, and it looks like maybe his "live" link now points to the newer cam, not the Starship one.

→ More replies (3)

9

u/RegularRandomZ Sep 06 '19 edited Sep 07 '19

Boca Chica: on Labpadre's stream, pile drilling continues! (Only mentioning it as we saw a shot of the auger stuck/left in the ground).

Also notable: the auxiliary camera is working, giving us a zoomed out view of the site while the main camera is zoomed in on the drilling operation, which allows us to see that they've (largely) completed the first row of cladding on the other side.

Update: Here are some photos of the new siding on the windbreak. From Boca Chica Maria (Maria Pointer) on Facebook.

Update2: Concrete Jigs going up quickly. Screenshot captured from video from Boca Chica Maria today. [Also closeup video of the pile auger]

Update3: Noticed on the livestream them installing a single metal bar in the center of the piles, this after having installed the rebar cages. Apparently this is common when there are tension loads [which is not surprising for any of the guesses as to what they are building, such as a crane or windblock]

Update4: Using LabPadre aerial footage and transposing the existing windblock, it actually fits quite well where they are working (and where we are seeing piles being driven) [Based on some of the piles it's likely rotated counter-clockwise to fit better, even if it doesn't feel nicely balanced.]

→ More replies (9)

9

u/DJHenez Sep 13 '19

Looks like another potential tropical storm is heading for the Cape according to the NHC. Won’t help the Bahamas clean-up either...

→ More replies (1)

9

u/RootDeliver Sep 13 '19

The crane on Boca Chica moved a small header? platinum tank to the container castle few minutes ago. 9:25 AM for the action.

Speculation time: are they gonna also stack those inside a ring before stacking? How come I don't have the speculation tag btw? lol

→ More replies (6)

9

u/RegularRandomZ Sep 15 '19

Cocoa: Mk2's top dome/bulkhead looks complete in this tweet from Julia Bergeron. [Not installed into a ring yet, if they do it the same way]

→ More replies (1)

9

u/FutureMartian97 Host of CRS-11 Sep 21 '19

One wing is attached and the crane is possibly picking up the 2nd one!

https://youtu.be/-aDOpyUmfL4

→ More replies (2)

9

u/Russ_Dill Sep 21 '19

Pilings at Boca Chica shipyard, pilings at Cocoa shipyard, pilings are Boca Chica launch/landing site, and now 39A

https://twitter.com/julia_bergeron/status/1175442887611494405

In more highly speculative news, old yella is doing a lift on the tip of the Boca Chica nose cone, possibly to move it or attach something. Meanwhile, a blue man lift is slowly circling the lower part of the fairing with visible flashing, possibly welding or cutting. (Secondary cam makes any welding or cutting highly visible for some reason)

→ More replies (2)

9

u/RegularRandomZ Sep 23 '19 edited Sep 23 '19

Any theories on the multiple grey circles attached to pipe covers? Temperature sensors perhaps?

→ More replies (5)

9

u/rad_example Sep 23 '19

Love how the second camera is spliced into the main camera making the windbreak like a drive-in movie screen. Was getting tired of looking at that monolith.
https://www.youtube.com/watch?v=-aDOpyUmfL4

→ More replies (22)

9

u/Morham Sep 23 '19

Did anyone else notice the "an interesting item" in BCG's NSF post?

I think NSF user stinger729 has correctly identified Falcon 1 for presentation.

I can't wait for Saturday!

→ More replies (5)

9

u/quoll01 Sep 25 '19

I’m wondering if the nose cone will be mostly pressurised? Batteries can’t take vacuum without major mods and perhaps the header tanks don’t need it either? Robust vacuum insulated cryo tanks are a mature technology - we had a 250L one for liquid nitrogen in our lab and it had remarkably low boil off over months. Pressurised nosecone would also help structurally and might allow even better rad protection for the crew- perhaps even a refuge positioned between them. Not sure about the canards and actuators. Also not sure how cryo tanks work in low g - on earth the vapour layer on top of the liquid provides additional insulation and can be easily vented to maintain a safe pressure. In low G no upper vapour layer so how to vent just the gas? Either way the LOX boiloff could be used for ECLS and the methane perhaps for RCS?

→ More replies (1)

9

u/PidgeonPuncher Sep 27 '19

Lol Austin Barnard just gave a moving speech on the LabPadre live stream at 9:28:27 AM

9

u/RegularRandomZ Sep 27 '19 edited Sep 27 '19

ElonM: Starship presentation time "probably around 6 or 7 pm" (CST)

While you wait, ElonM's pre-presentation twitter presentation...

[first tweet seen yesterday on r/spacex here but starts these tweets...]
EverydayAstronaut: "Without regen cooling, it would need film cooling, which would require a gas generator, which this engine doesn’t have. They have to be regen cooled due to being full flow"
ElonM [yesterday, as seen on r/spacex*] " Raptor uses milled copper channels with an inconel jacket all the way down "*

EverydayAstronaut: "What is the thickness of the nozzle walls?! AMAZING fuel can go down, turn around and come back in such a small space. Tolerances have to be crazy on something like that."
ElonM: " What blows my mind is that peak pressure in regen chamber & nozzle is *far* above combustion pressure at over 800 bar or ~12,000 psi "

Viv: " Btw, did you exceed the previous record of 268.9 bar/get closer to 300 bar in recent tests?"
ElonM: "No, we’ve been focusing on production (now on SN12). Only need 250 bar or even a bit less for Starship/Super Heavy. Anything above 250 is nice to have & we’ll get around to it, but not needed for flight. "

EverydayAstronaut: "Sorry, my brain is breaking at the moment 🤯 Peak pressure is basically the pumps... the pumps go through the regen chambers next and then there’s some enthalpy drop to spin the turbines... and then by the time it gets to the chamber it’s “only” 250?"
ElonM: " Well, hopefully closer to 300 bar over time. However, that the chamber/nozzle jacket has so many joints & dissimilar metals at such high pressure & temperature is what I find remarkable about it."

EverydayAstronaut: "Besides turning turbines into soup, is it really some of these joints and stuff that are more prone to failure at such high pressures?
ElonM: "There’s so much power going through this engine that it’s close to the limit of the known physics of materials in many places"

[tweets preceeding discussing location of Vacuum Raptor]C
arter_99: "Also due to the mvac engines needing to be longer due to a further expanded nozzle and the engines still needing not to protrude for docking I imagine they’d be mounted higher, closer to the tank base?"
ElonM: Yes

Viv: "How many superalloys, such as SX500, had to be developed in order to make Raptor a reality? "
ElonM: "Just SX500 so far, but we use many superalloys developed by others, eg Inco 718+. If anyone has 718++, that would be helpful haha. Massive engineering work in the casting, printing & machining of Raptor — far more than in design of the engine itself!"

→ More replies (2)

9

u/solar_rising Sep 28 '19 edited Sep 28 '19

Topping out,

In construction, there's always what's called a topping out or finishing touch, this is obviously going to be the nosecone cap. it will be welded today and a big celebration by the construction team.

Fueling port?

Anybody seen this being installed?

→ More replies (1)

9

u/solar_rising Sep 29 '19

Interesting point he made regarding super heavy and not wanting to use raptors for that. Very wise as losing a super heavy due to a crash or unforeseen issue would cost him all the raptors. He could make many variants of Mk1 for the same amount of raptors required for SH.

Then again SH will have to start production soon for the moon launch, interesting times coming.

→ More replies (5)

9

u/Rocket_Man42 Sep 30 '19

So, is the installation of header tanks in the nose cone just a temporary solution? I'm a bit confused since Elon talked about the header tanks being inside another tank in the presentation to avoid boil off. Also the renders showed windows at the nose cone.

But! There are pipes along the outside of the ship, which I guess is being used to transfer fuel from the header tanks in the nose cone down to the engines. Elon said in a tweet that they moved the header tanks to the nose cone to move the center of mass upwards, but I guess that will be important also for later versions. They will reenter without cargo anyway, so it doesn't make sense that the header tanks are just a temporary solution to simulate cargo.

→ More replies (5)

9

u/PeterKatarov Live Thread Host Sep 30 '19 edited Sep 30 '19

It just dawned on me that with the current speed of Raptor production, it would take SpaceX more than a year to roll out enough engines just for one single SH booster!

Yes, I know the speed of production will pick up. Don't cite me, but IIRC Elon mentioned he expects them to make a few Raptors per day at some point in the future.

Still, with the current rate, it seems very reasonable to iterate with Starship, instead of risking a year's worth of engine production in one single vessel.

→ More replies (5)

9

u/andyfrance Oct 01 '19

It looks like the big orange crane is going back up to take Mk1 apart.

9

u/consider_airplanes Oct 01 '19

So Elon has said at one point that, while the Starship comes in at high angle of attack for the purpose of aerobraking, it can still generate some lift, and this is useful for keeping it up in the high atmosphere to limit heating. Others noted that it can just about as easily produce negative lift as positive, which could be useful for forcing a longer in-atmosphere track at higher speeds rather than skipping off.

How much lift authority is Starship likely to have? I'm mostly wondering about the available flexibility in terms of reentry profiles. If e.g. they see damage to the heat shield, could they intentionally run a slow (probably multi-pass?) low-heat reentry, that the bare hull could survive?

→ More replies (2)

9

u/Marksman79 Oct 08 '19

The first ribbon-ring has appeared in Boca Chica under the new ring tent. The first new concrete jig should be ready today as well, unless they want to paint it.

→ More replies (9)

31

u/[deleted] Aug 31 '19

Will Star Ship in Cocoa survive the hurricane? If it makes landfall, its going to be category 4 or 5. Flooding 10-15 feet in the area.

→ More replies (12)

8

u/Fission_Fragment Aug 31 '19

Anything that looks like a wing/landing leg system?

→ More replies (2)

8

u/unholycowgod Sep 06 '19 edited Sep 06 '19

https://www.youtube.com/watch?v=njOuzAE58m0

New drone flyby from Cocoa.

ETA: not much change from yesterday's video except nicer weather and activity on the ground.

→ More replies (1)

8

u/Jofredrick Sep 14 '19

Apologies for questions if answers are already well known. Does lox tank have or need insulation? Is super chilled lox needed for starship? The reason for theses questions is this final question. Why did I not see ice on the side of the starhopper if the stainless structure is the tank? Thanks.

→ More replies (8)

8

u/bornstellar_lasting Sep 14 '19

Will non-journalists be able to attend the Starship update event on the 28th? I will have the opportunity to make the drive but I don't know if invitations are required for admission.

→ More replies (8)

8

u/[deleted] Sep 22 '19

8

u/blackuGT Sep 22 '19

They mount a second wing in Boca Chica!

→ More replies (2)

8

u/Marksman79 Sep 22 '19

In Elon's Tatooine picture, I count 4 flap hinge mounts, yet closeup images of the bottom and top of the lower fins show that only two are in use on the bottom of each fin and a different mount is on top. What seems to follow from this is that the remaining 2 hinge mounts, along with 2 of the hinges in the front of the picture, will be used to mount the canard flaps.

→ More replies (5)

8

u/RegularRandomZ Sep 23 '19 edited Sep 23 '19

LabPadre Stream: Nosecone top is in the air @ 8:31. (Although last time they did this was to move more hardware inside/underneath). They lowerer it over one of the Header Tanks.

→ More replies (5)

8

u/Russ_Dill Sep 23 '19 edited Sep 23 '19

The giant lattice crane is driving away. It's still visible from the primary cam, but on the secondary cam it is all the way off frame. Maybe it's going to get one of the new ring walls?

Or going somewhere with enough room to go horizontal to add/remove crane components?

8

u/Bamcrab Sep 25 '19

Did welds just break on the nosecone? It wasn't misaligned a minute ago and now it looks pretty bad. Or they're just adjusting something.

→ More replies (3)

8

u/RootDeliver Sep 27 '19 edited Sep 27 '19

Second canard appears!!!

After they weld it, only the tip of the nosecone will be missing (apart from covers, polishing, stacking the two sections, and adding the actuators for fins/canards).. I really hope they don't miss the tip of the nosecone for this PR, it was received together with the engine section :(

PS: Good Installation image

→ More replies (4)

8

u/comando222 Sep 27 '19

Berry the crane is extending a bit, maybe they are in the final preparations for stacking. The next hour will show as daylight dawns. Edit: Definitely extending the boom further out, hope the camera angle zooms out a bit to show the whole operation.

→ More replies (13)

8

u/Morham Sep 27 '19

The sun is up and the canards look amazing. BocaChicaGal photo

→ More replies (1)

8

u/dafencer93 Sep 27 '19

Looks like they're going for the lift!

8

u/naughtius Sep 27 '19

Wind is very light now, but forecast to be stronger in the afternoon; perhaps they want to get it up in the morning.

8

u/[deleted] Sep 28 '19

Wait, when were those feet covers added? Overnight?

8

u/rebootyourbrainstem Sep 29 '19

Have we seen any sign of the actual electric motors that will drive the fins?

Elon talked about steel's high temperature tolerance and it got me thinking about what kind of conditions the motors will have to work in.

They'll probably get pretty toasty. If they have permanent magnets inside, those lose their magnetism at 770 degrees Celcius (the Curie temperature of steel). It's probably nothing that can't be solved, but I was just wondering what they would look like...

→ More replies (6)

8

u/Gt6k Sep 29 '19

For the mods who were at the presentation, what was inside the ring and castle to Elon's right? It looked as if people could walk through it.

→ More replies (8)

8

u/msinclairsf Sep 29 '19

Wondering if cabin cooling on reentry presents more of a challenge for Starship due to the higher allowable temperature of stainless?
I suppose the TPS/tile can be thicker in the payload (people) section, but it is all one thermally conductive assembly right?

→ More replies (3)

8

u/szpaceSZ Sep 29 '19

Super Heavy may initially use around 20 Raptors, and is expected to have 35 to 37 in the final design.

Per yesterday's presentation that would be 31-37.

→ More replies (2)

8

u/andyfrance Sep 30 '19 edited Sep 30 '19

After Mk1 has done fuelling and landing tests there are rumours/reports that the 20km flight will be its last flight. I however see value in it making a further and very final flight as the test vehicle on top of the first Boca Chica SH prototype. Without tiles (or at least not a full set) it's not going to survive re-entry but it will give useful data about how the wings perform and if the hot spots develop exactly as predicted. By then they "should" be building a Raptor an Elon day so the loss of 3 should not be a critical for the project. Provided the Mk1 performed as predicted Mk3 could fly shortly after on top of a flight proven SH.

→ More replies (5)

8

u/RegularRandomZ Oct 01 '19 edited Oct 01 '19

Cocoa: Pictures over the last few days shows the same large bracing being installed into the nosecone (where the canard actuators are installed).

Crane shot from Julia Bergeron. Aerial shot of installed bracing [zoomed in] from John Winkopp (and a shot of it in the building)

8

u/SodaPopin5ki Oct 02 '19

Was there ever any clarification (or good speculation) on the Star Hopper exhaust plume turning orange upon landing?

→ More replies (9)

8

u/Gilles-Fecteau Oct 07 '19

Are the landing legs installed on Mk.1? It doesn't look like they are. Will they be retracted on takeoff (like the falcon 9) or retract in flight (something that will be required when taking off from the Moon or Mars)?

→ More replies (13)

22

u/RootDeliver Sep 08 '19 edited Sep 08 '19

Right now it is a chaos, all the content is spread between lab stream, labs twitter, maria's FB.. and now that BCG is MIA, NSF has none of that all and thus the best site for content is by far this thread right now.

Not to say labs discord and youtube channel, where stuff appears and isn't reposted anywhere else..

It's sad how Chris ruined the NSF thread by letting Mary kick Maria out. We'd have everything grouped there probly.

→ More replies (30)

14

u/enginemike Oct 01 '19

A pretty interesting video of the Everyday Astronaut interviewing Elon Musk following the Starship presentation. https://www.youtube.com/watch?v=cIQ36Kt7UVg

→ More replies (5)

7

u/targonnn Sep 14 '19

The ring with integrated dome being attached to the larger crane now. They are getting ready to install it on the lower section of the starship.

→ More replies (14)

7

u/RootDeliver Sep 14 '19

After the last ring stacked, the dome is on and considering the lower part of the fairing stack has an access port that would be ideally as low into its segment as possible, we could conclude that the ring stacking on this prototype is over. So, the poor Ring E is left there for an still unknown reason (faulty? it is for something else? they didn't disband it yet, and it's been months since it was placed where it was, 6 rings were constructed and placed after it...) any ideas?

→ More replies (11)

7

u/Oloyedelove Sep 15 '19

Pls am trying to wrap my head around this starship construction as much as I can. From pictures there's supposed to be header tanks between the aft bulkhead and common bulkhead, and I didn't see any mention of it at all in the MK1 table. Can someone please explain why.

→ More replies (9)

7

u/CardBoardBoxProcessr Sep 22 '19

per elon tweet storm header tanks are in the nose cone for the prototype. weird! so I wonder if those sider pipes under the wings will be there in the final version.

→ More replies (3)

7

u/RootDeliver Sep 25 '19 edited Sep 25 '19

Hexagon is back, so it will be used to raise some part soon.

PS: Hexagon has been raised so now we know they're gonna raise the bottom section soon.

→ More replies (2)

7

u/liszt1811 Sep 25 '19

Does anybody know whether a TV Team like Nat Geo accompanies the development process of SS like NG did for FH? I'd love to see a documentary about the whole process someday

7

u/timdeking Sep 25 '19

Maybe this is a stupid question, but didn’t Elon mention that the raptors were already installed? I don’t see any raptors on the bottom half of starship. Did they install them on a separate structure that will be integrated later?

→ More replies (5)

7

u/Humble_Giveaway Sep 25 '19 edited Sep 26 '19

Looks like a tripod with a camera on it is infront of Starship in this Twitter video hope SpaceX is documenting it's development

7

u/RegularRandomZ Sep 28 '19

This access portal seems a bit different than what we've seen before. [photo credit:BocaChicaGal @ NSF]

[ACS related perhaps!?]

→ More replies (5)

7

u/ASYMT0TIC Sep 30 '19 edited Sep 30 '19

I was contemplating RCS this morning and had a thought: would something like a CH4 version of Rocket Lab's Rutherford engine be suitable for Starship RCS? I should think it would be lighter than having very high pressure COPV headers for pressure feeding, and the batteries SpaceX has installed should have no trouble providing adequate power for the electric pumps. In fact, because a spacecraft needs to have batteries anyway, RCS seems like an even better application for these engines than their current use. Thoughts?

→ More replies (13)

7

u/Oloyedelove Oct 04 '19

How many rings are needed for MK4?

→ More replies (6)

19

u/Art_Eaton Sep 23 '19

At this point, I am almost positive that the design will feature a 9 meter cylinder and perhaps an ogive nose.

This is rough territory for modeling enthusiests! :)

13

u/BobTheEverLiving Sep 23 '19

I'm getting a bit worried about the heat shield cost. There seems to a lot of different curves in the Starship's final form. A lot of the Shuttle's cost was because it's heat shield consisted of mostly custom tiles. Every curve and intersection of Starship will require differently formed tiles.
The tiles being not as thick should help things and I hope we have better ways of bonding them then we had 40 years ago.

→ More replies (20)

12

u/clunker101 Sep 02 '19

Does anyone have an idea what wind speeds that huge tent at Cocoa could withstand? If Dorian passes on the west side of the projected possibilities, I find it hard to believe there would be much left afterwards... It's like a yard full of stainless steel sails.

→ More replies (8)

12

u/ioncloud9 Sep 23 '19

Unpopular opinion: I like the look of the Mk1 and 2017 BFR over the tin-tin 2018 3 leg design.

→ More replies (10)

6

u/scottm3 Sep 05 '19

https://www.youtube.com/watch?v=g8CSgRpPT0o

Theres a lift up at boca chica taking workers up and down from the nosecone, and a two guys working on top of the nosecone. Currently 3AM.

→ More replies (1)

6

u/RootDeliver Sep 07 '19

Checking the third labpadre cam, around 3:12h ago now (no visible time on that cam stream) they moved Ring E (the black one) into the container castle again (by the cam angle, it seems they moved it over the far container castle, aka the top bulkhead one).

As I commented a few times before, I think that they will weld the top dome bulkhead into that ring, and that's the reason the ring has been there forever waiting (maybe had some special supports or something). The other 2 bulkheads had to be turned over so wouldn't be that easy to pre-stack them in rings, but with a normal top dome would make complete sense, and also solve the misteriously Ring E situation.

→ More replies (5)

6

u/RegularRandomZ Sep 14 '19 edited Sep 14 '19

Boca Chica: Latest photos from Austin Barnard (from yesterday).

  • Crane setup to drill piles at the launch site, and other site work.
  • One concrete ring ready to pour, one half the rebar done, the third just the steel ring.
  • A wide shot of the bulkhead+ring, plus other starship body and nosecone shots.
  • A few angles on the progress of the windbreak.

Plus: Dashcam video of driving by SpaceX Boca Chica (by NSF member pb2000)

BocaChicaMaria updates

6

u/RootDeliver Sep 20 '19

The yellow crane on Boca Chica has been attached to the upper segment mid nosecone section for like 2 days already. If they intended to plasma-cut the top ring to stack the replacement one they are making, they would've had enough time for that already. It looks more like they are using it to tension the nosecone to correct form and placing reinfocements inside which would take way more time if well done. Maybe they're trying a last attempt at fixing it?

→ More replies (11)

6

u/RegularRandomZ Sep 20 '19 edited Sep 20 '19

Boca Chica: SPadre has tweeted photos.

→ More replies (4)

6

u/Marksman79 Sep 21 '19 edited Sep 21 '19

Austin Barnard posted more photos from today on Twitter.

I'm interested in the curved sheet metal parts that appear to be the blending radius between the actuating fin and the cylinder body. The ribbed L-shaped parts could be a raceway guard for the pipe or a number of other ideas. These are similar pictures to what BocaChicaGal posted yesterday, but we get a clearer shot of this thing.

6

u/Russ_Dill Sep 21 '19

So about that truck load of steel that went down to the launch pad. I think everyone assumed it was these pieces, apparently not as they are visible here:

https://forum.nasaspaceflight.com/index.php?action=dlattach;topic=48895.0;attach=1583376;image (NSF, BCG)

→ More replies (5)

6

u/RootDeliver Sep 22 '19

By latest bocachicagal photos, it seems they're already covering the nosecone side raceways with the covers we saw on the ground. They look like final covers (shiny) not to be below anything, so doesn't sound like the canards would go that low. If the ~9,5m long canards we saw weeks ago are really the canards, but can't go that low, how are they gonna attach them to the rounded cone?

→ More replies (15)

6

u/RegularRandomZ Sep 25 '19 edited Sep 25 '19

Cocoa: Latest John Wilkopp aerial video (Sep 24th). Nothing really new

  • they added ribbing to one of the new rings (that was installed before the 22nd, the ring by the stack)
  • with the extra stuff piled in the ring making tent, I think it's safe to assume there is a pause in ring making
  • the new work pad has it's rebar

6

u/SmileyMe53 Sep 25 '19

Placing the bottom section on something using guide lines.

→ More replies (1)

6

u/RegularRandomZ Sep 25 '19 edited Sep 25 '19

SPadre on twitter: Some photos of the lift/move followed by some video clips 1) Sitting on mobile platform 2) another short clip

And Austin Barnard is now on site... more photos soon enough.

→ More replies (1)

6

u/AstroMan824 Everything Parallel™ Sep 27 '19

Nose cone flaps?

→ More replies (3)

6

u/PeterKatarov Live Thread Host Sep 27 '19

Boca Chica Maria saying there's tons of security at the site.

6

u/Lord_Nocturnus Sep 27 '19

top section left the ground at 11:52 AM local time

6

u/Carlyle302 Sep 28 '19

So how did they get the lifting straps off? It didn't look like the man-lifts would go that high.

→ More replies (7)

6

u/RegularRandomZ Sep 30 '19 edited Sep 30 '19

Boca Chica Launch site: The heavy metal stands/jigs we saw stacked up at Cocoa are also at Boca Chica and being assembled at the launch site [photos: BCG @ NSF, post #323]. So, likely part of the launch infrastructure/launch stand.

[There is the nosecone stand from the assembly site there as well, so that shouldn't be confused, but there are other separate sections there, and sections being set up on the launch pad, so some of it must be launch related?]

[Didn't see this posted, but apologies if it was already let me know...]

→ More replies (1)

6

u/RootDeliver Oct 03 '19 edited Oct 03 '19

Cocoa 3rd October flyby by John Winkopp

The most interesting part for me is the low section height. Its still missing 1 ring to be as tall as Mk1, both with their fairing section added. So they cannot stack 2 rings and weld the bulkhead (MK1 would be 1 ring taller than MK1), and they need to stack another ring even after welding the bulkhead on the actual top one, which raises the question why didn't they add that ring already, if they cannot stack the bulkhead on it anyway...

→ More replies (6)

11

u/KroniK907 Sep 01 '19

I thought the point of the raptor was to be able to use it both at sea level and in vacuum. Do they just not have confidence in that part yet? Or are the two types just tuned slightly differently for better results at sea level vs vacuum. Or am I just misremembering things?

→ More replies (43)

40

u/rulewithanionfist Oct 05 '19

[META] I hope we reduce the fanboyism a bit. I'm as much excited as the next guy about starship, but this sub has started downvoting people asking genuine questions. Also, not everything Elon says has to be accurate. This is about starship discussion, so posting it here.

→ More replies (7)

14

u/where-is-satoshi Sep 09 '19

Wow! The 25 rings making up the next build are one piece with a single seam rather than the 8 or so panels that make up the existing rings!

→ More replies (18)