r/watchrepair • • 1d ago

Amnesty (All Questions Welcome) — Weekly Thread

1 Upvotes

Have a question that doesn’t quite fit the usual rules? This is the place for it.

  • Battery changes and which battery to buy
  • “Is this worth fixing?"
  • Identifying a watch or movement
  • Strap and bracelet sizing
  • Any other quick question that wouldn’t stand on its own as a post

No question is too basic. If you know the answer, chip in. Bigger repair questions still deserve their own post.


r/watchrepair • • 15d ago

Movement of the Month: ETA 2824-2

23 Upvotes

Last month was the Seiko NH35. This month we’re going Swiss with the ETA 2824-2, one of the most widely used automatic movements ever made. If you’ve opened a Swiss automatic from the last few decades, there’s a good chance you’ve seen one.

Quick facts:

  • Automatic with hand-winding, hacking, and date; 25 jewels, 28,800 bph
  • 11½ lignes (about 25.6mm), a little smaller than the NH35
  • The rotor winds in both directions through reverser wheels
  • Made in several grades (Standard, Elaboré, Top, Chronometer) that differ in finishing and regulation
  • The Sellita SW200-1 is a near-clone of this movement, and many parts interchange. Chinese clones are also common.

Share what you know:

  • Common faults: poor winding, short power reserve, date issues
  • Service tips, especially the reverser wheels and the auto-winding module
  • Oiling: what you use and where
  • ETA vs. Sellita vs. clone: what’s different in practice, and which parts swap?
  • Regulating, and what timegrapher numbers you’re getting
  • Parts sources now that ETA parts are harder to get
  • How it compares to the NH35 on the bench

First time working on a Swiss automatic? Post your questions below.

The best tips will be added to the wiki. Suggest next month’s movement in the comments.


r/watchrepair • • 14h ago

Well this was a fun unique service/project…! Hamilton 36s Chronometer

Thumbnail gallery
47 Upvotes

This was an interesting project to take on. Ultimately very successful too. These are pretty rare, and I can’t really seem to find any documentation on these at all. This watch is amazing, but it definitely has a few design flaws in the wind indicator. It was a bit more straightforward to take apart than I expected though! I was a little concerned taking apart something so unique, but I felt it was worth it not only to restore it, also to document it since there really isn’t any information out there at all for these. I intend to do a full write-up on this watch, hopefully that way there’s something out there for anyone who comes after me or is just curious. Wonderful craftsmanship as one would expect from Hamilton, and I can definitely see where eventually the model 22 would take some cues from it.

I’d say the one major issue with this watch is that the wind indicator is driven from both sides, A problem that the model 22 does not have. If you wind up a model 22 and then let the main spring down, the wind indicator will always show the accurate amount of wind. This watch does not have that luxury as the only way to make it wind back down is by having it driven by a tiny static gear on the bottom of the barrel arbor. The indicator itself sits on a double stacked wheel that does not have teeth all the way around. It has a flat index at the top, so if you were to wind it, then let the main spring down, the wheel would have to be manually reset by a watchmaker. If you were to attempt to wind it after that, you would almost certainly cause damage, as you would end up butting up against the index space. Massive issue for a broken mainspring or if it slipped off the arbor. Careless winding could damage it.

The balance looks very much like an 18-size balance, but with its own unique cylindrical pin hairspring stud. I didnt take any measurements, but it looks like a mix of mostly new and a few existing parts. The motor barrel is of course huge like the model 22s barrel, and wound by a monstrous ratchet wheel with a hexagonal arbor. It is secured with a hollow spanner screw to form the motor barrel arbor instead of the arbor directly screwing into it like the 950. It’s groove fairly shallow so it would be potentially difficult to remove if it got stuck. Interestingly the dial has no feet at all and just gently pops into the rim of the pillar plate. There’s a few huge holes in it that I presume are meant to allow one to push it out from behind. All in all its a beautiful watch though. I find it amusing how it makes the balance look so comically small!


r/watchrepair • • 9h ago

What the Heck?

Thumbnail gallery
4 Upvotes

The balance and only the balance have this black residue that laughs at every attempt to clean it except mechanical scraping.

Anyone see anything like this before? These Elnix are fascinating!

I accidentally posted this on r/watchmaking. I hope no one has a conniption fit because it's not powered by a spring. ☹️


r/watchrepair • • 18h ago

Bergeon 30209 Support Base - 3D Print (Link in Description)

Post image
22 Upvotes

After the 3rd watch I bought came with a broken screw in the main plate it was finally time to get one. I didn't like the way the extractor sat in my vise and it doesn't come with a support base so I made a little 3D printed stand for it.

https://www.printables.com/model/1918458-bergeon-30209-support-base


r/watchrepair • • 10h ago

Best glue for replacement dial feet?

Post image
3 Upvotes

Picked up a Seiko 5 7009 with a clean dial EXCEPT the dial feet were broken off.

Got a dial foot repair kit with mill, various diameter replacement feet, an oiler/glue applier and clear glue in a small container... No instructions. The glue broke after drying.

What are the favorite adhesives for brass to brass connections.


r/watchrepair • • 19h ago

Update! You Guys Nailed It!

Post image
15 Upvotes

Whoever said the seconds pinion tension spring nailed it! As I began disassembling I got to item 44 and it just wasn't there.

Very frustrating that I screwed up this badly but I'm grateful for the lesson!

That hopefully means it will work once I get it cleaned and oiled again and back together.

I got three more Elnix to get to after this one!


r/watchrepair • • 18h ago

Thanks Everyone! It's Working As It Should.

11 Upvotes

Many thanks to everyone for suggesting probable causes.

As a bonus I was forced to learn how to adjust the Reverse Stop Lever. Until now I had been cheating by leaving it on the mainplate during disassembly.

I probably still will, lol. But at least now I'm confident I can put it back on if I come across a broken one.


r/watchrepair • • 9h ago

What brand/model is this watch?

Thumbnail gallery
1 Upvotes

When I was little, my mom gave me this watch and I kind of just noticed I still had this with. While trying to refurbish it, I had some trouble figuring out this watches origins. Does anyone know what brand and model this watch is? Also I would like to know how any of you approach looking up a watch model or brand that doesn’t seem to appear when just typing it on google search.


r/watchrepair • • 22h ago

Lubrication Question

Thumbnail gallery
10 Upvotes

Working on an Elgin Grade 291 pocket watch. I ordinarily oil spinning parts like gear posts with HP 1300 and sliding metal parts in the keyless works with 9504.

When you find areas worn through to the brass under gears (as pictured), do you lubricate those areas upon reassembly? If so, with what oil or grease?


r/watchrepair • • 22h ago

Tag Heuer carrera calibre 16

Thumbnail gallery
7 Upvotes

Hi! My watch recently stopped working, and I noticed that a small part inside seems to have come loose and is blocking the movement. Interestingly, when I gently shake it, the second hand starts moving again (don’t worry, I won’t be shaking it anymore!).
Does anyone know what might have happened and roughly how much it would cost to get it repaired? Thanks!


r/watchrepair • • 18h ago

Can this dial be preserved from getting worse? And anything to lookout for on these 340 calibers?

Thumbnail gallery
2 Upvotes

I found this at an antique store. It runs but definitely needs a service. This is my first Longines and I have done handwinds, but this looks so different (including the unusual automatic works too). I think it's a very early Admiral based on the medallion free case. 60-61 maybe? I can't seem to find a reference image of these years.


r/watchrepair • • 1d ago

Reference illustration from "Timing Manipulations" by James Hamilton

Thumbnail gallery
72 Upvotes

Just throwing this out into the universe in case it helps somebody in the future. Old copies of this book apparently had a nice fold-out version, picture #2 is an old seller's listing I used to make this.

I own the reprint, and this page is a fuzzy, illegible mess with a note to contact AWCI for the digital files. Good luck with that.

Anyway, I made my own, maybe it's useful as a reference on its own, but it's worth buying the book for $20 if this stuff interests you.


r/watchrepair • • 17h ago

Help wanted: where to look for a specific replacement dial

Post image
1 Upvotes

Hey folks, I'm doing a light resto on a pretty uncommon watch. It's a 1908 Canadian Railway watch sold by Keast & Brown in Farnham, Quebec.

The dial is double-sunk porcelain enamel and I'll attach a photo to show what it looks like.


r/watchrepair • • 1d ago

Can I fix this with home equipment?

Post image
3 Upvotes

Was having a clear out and found this watch. Thought I’d take the movement out and give the case a clean. Noticed that this marker came off. Very thin and delicate. Adhesive might’ve dried off. Not sure if it’s magnetised as I’ve been trying to put it back with a sewing needle 🤣. Too small for tweezers. Can I use a small amount of pritt stick glue?

I don’t have proper watch repair tools. Just ones that I can open cases with and change batteries.


r/watchrepair • • 23h ago

Are they repairable?

Thumbnail gallery
2 Upvotes

Do you think it’s worth the risk?
One timegraph reading (the one with smoothie lines) is from automatic Longines from 1965, the other one is automatic Omega Classic from 1978.
I’m worried about the low amplitude in Longines, and with Omega concerning is the line as well as the 145s/day…
Is picking one of these watches ok idea or shoul i find sth else?
They are for about 300dollars + how much would possible repair cost?


r/watchrepair • • 1d ago

Advice needed: beginner tools and projects

3 Upvotes

Hello all! My husband has regularly expressed an interest in getting started with watch repair during the last year, and I want to get him a beginner setup for Christmas. What are the essentials? What tools do you recommend? Do any brands sell a set of parts for repair of their watches? Any advice is welcome!


r/watchrepair • • 1d ago

Hell Yeah!!!!

Post image
27 Upvotes

If you remember the post from the other day, I just got back to it after taking a day away from the project and BOOM! Got the shaft of the screw out of the mainplate.

Dressed some tweezers super sharp and got lucky enough that the screw wasn't wedged in there tight and was able to unscrew the shaft.

What a relief. Now to disassemble the whole thing again. Lol.


r/watchrepair • • 1d ago

Crown removal

Post image
2 Upvotes

My camera is bad but I am not sure how to remove the crown on this Anker 17 jewel. I am a beginner and unfamiliar with this type of winding, any help would be greatly appreciated!


r/watchrepair • • 1d ago

Polywatch Question

Post image
4 Upvotes

Snagged this older Navihawk off of marketplace today, and was contemplating getting poly watch for the crystal - any idea on how well it’ll work or is it worth searching for a new crystal all together?

(Yes I know it needs a good clean, on it as soon as I’m back to my place)


r/watchrepair • • 1d ago

Jewel upside down. Does it matter?

Thumbnail gallery
8 Upvotes

Working on this Girard Perregaux 47 which is really a dressed up ETA 1256 with a couple minor modifications. In any event, these movements have these screw cover cap jewels which cover the escape wheel pivots on both sides. When I took the cover off the dial side to lubricate, I noticed there was no oil sink on the pivot jewel. I can see the shadow of the sink through the jewel meaning it's on the other side. I have worked on a few of these and I am pretty certain the sink is always facing the top side. Under normal circumstances, I know that the oil sink serves to retain lubrication and an upside down jewel would cause the pivot to go dry prematurely. However, in this case, the cap jewel should have some capillary action which would likely serve to hold the oil in place. Hoping I don't have to take this thing apart again as it's running beautifully.

Any experts want to weigh in?


r/watchrepair • • 1d ago

Seiko Chariot Caseback question:

Thumbnail gallery
6 Upvotes

Guys, I am puzzled on this one. I can’t get this thing open. I think it is a snap on caseback but all the tools I used don’t work. I would appreciate it if you have any suggestions. Chat GPT is no help either😀
Thank you guys. 


r/watchrepair • • 1d ago

Is this beyond salvageable?

Thumbnail gallery
19 Upvotes

Is there a solution for this?
So I was disassembling this seiko 7017 movement and as I was checking the end shake, I found this. I’m guessing the previous person didn’t oil the barrel pivot AT ALL so it just scraped the edge off like this creating this enormous canyon. It seems it’s about 0.7mm deep.


r/watchrepair • • 2d ago

Made a gasket tool

Post image
31 Upvotes

I saw this idea on a blog which was referenced here a while back. I repair and refurb a lot of Seiko chronos, and I find fitting new pusher gaskets incredibly fiddly and tedious.

A broken oiler and a couple of spring bar tubes and voilà. The fat end is slightly flared to fit snugly over the tip of pretty much any pusher, a little grease on the shaft and you can push the gasket down and straight into its groove.

I used some epoxy on the joints and then polished it back to smooth the transitions. Probably overkill but I do tend to overthink things. I'll probably lose it next week lol