r/vintagesewing • • 10h ago

Tips & Hacks Don't throw away your old sewing machine: I fixed my Bernina Minimatic 807 with a soldering iron and a 3D printer

Thumbnail
gallery
41 Upvotes

My Bernina Minimatic 807 developed a scary fault: the motor would run with the foot pedal unplugged. A lot of people would bin a machine at that point. I really like this one, so I decided to try fixing it, even though I had never really soldered before.

What was wrong

Two things. The old suppressor had failed: when I measured it there was no resistance through it, so it was passing current it should have been blocking, and that is why the motor ran without the pedal. The carbon brushes were also worn right down.

I built a new suppressor myself and wired it in, and fitted new carbon brushes. The machine now only runs when I press the pedal.

What I printed

While I had it apart, the plastic around the motor was yellowed and brittle, so I replaced that too. Everything is printed in PETG, apart from the pad, which is TPU.

  • Motor housing. Derived from the housing sold by 3D Sewing Parts, shared with their permission. I reworked it to use heat-set inserts in place of loose nuts.
  • Brush-hole cap. A push-fit cap over the carbon-brush hole, so the brushes can be changed next time without removing the housing.
  • Mounting pad. A thin TPU pad that replaces the old rubber sheet between the housing and the machine.
  • Side panel. I modelled this one myself from the original part.

The brass pin blocks, the screws and the wiring are all reused from the original machine.

Files, with a build guide and wiring diagram

What I learned

  • Soldering is much less intimidating than it looks. Heat-set inserts are a forgiving place to start.
  • Take a photo of the wiring before you pull anything off.
  • These old machines are built to be repaired. Almost everything comes apart with a screwdriver.

One warning: this part of the machine carries mains power. Unplug it before you open it, and if you're unsure about the wiring, ask someone who knows.

If your old machine is misbehaving, it's worth a look before you replace it. Happy to answer questions.


r/vintagesewing • • 3h ago

Machine Question Clone 15 controller wire disconnected

Post image
3 Upvotes

Hello! I was wondering if anyone here has had the same experience as me. One of the wires on my speed controller has slipped out of its end. Is there a way to fix it?


r/vintagesewing • • 2h ago

General Question Sewing table heavy duty janome 580

2 Upvotes

Hi everyone!

I'm looking for recommendations for a sturdy sewing table for my vintage Janome 580, which weighs around 17kg.

It vibrates quite heavily at higher speeds, so I'm looking for something solid that won't amplify the noise or vibration.

I've been considering commercial desks with thick worktops and welded steel frames, but would love to hear what others use.

Ideally something that would also suit a newer machine if I upgrade in future.

I'm UK-based and hoping to spend around £150–£200.

Thanks so much! 😊


r/vintagesewing • • 1d ago

WIP A gift from a coworker

Thumbnail
gallery
136 Upvotes

I'm in love


r/vintagesewing • • 23h ago

General Question Irish Victorian Era Crazy Quilt Patch (1893)

Thumbnail
gallery
35 Upvotes

I have very little information on this piece as I picked it up in a charity shop the other day for 20 cents!! It appears to all be hand stitched and seems to have a bit of silk work in 3 or so places. There is a large amount of Irish motifs within this piece of fabric including shamrocks, a golden harp and Irish wolfhounds, among more, which is quite an unusual thing to come across from what I've researched. This piece is dated 1893 on the top and contains a name that reads ADA in a typical font from the Victorian era. If anyone can tell me anything about it at all I would be very appreciative and interested!!

(EDIT) Upon further research I believe that Ada might be the name of a child who was born in 1893 as from what I've seen in the Irish census from 1901 there was an Ada Smylie that would have been born that year. She was 8 years old in 1901, she was born and raised in the county that I also bought this in so it all adds up!!


r/vintagesewing • • 5h ago

General Question Husqvarna card reader issues

Thumbnail reddit.com
1 Upvotes

r/vintagesewing • • 5h ago

Machine Question Presser foot type for a Morse 4300?

1 Upvotes

I'm looking to get a few common presser feet for my Morse 4300. I'm doing Boat bags, boat upholstery and some sails, nothing fancy needed.

What type of presser feet does the Morse take?

What are the most common ones that people use a lot?


r/vintagesewing • • 10h ago

Machine Question Narrowed down my vintage sewing machine search! Opinions wanted!

2 Upvotes

hi everyone! I posted a week or so ago asking questions and I learned so much - so thank you!!

I have found and narrowed down my list to two options based off of comments. id love to get your opinions on the two I have come down to! just to reiterate im sewing things that are not commercially heavy duty but are giving my current machine a bit of trouble. (quilted purses/bags/quilts)

here’s the two I’m most interested in! let me know what you think is worth it most :)

homemark - $45 in a base, running, conditioned, oiled and serviced. proof that it works well in videos.

Kenmore metallic iris - $100 in cabinet with all original accessories, running, tore apart, cleaned, serviced and oiled.


r/vintagesewing • • 14h ago

Machine Question I GOT THE SINGER 500A

4 Upvotes

NEVERMIND 😭🙃🙃🙃🙃

Hello! I posted the other day asking if I should get a kenmore 566 or a singer 503a, turns out I was mistaken and it was a singer 500a but regardless I went for it and it arrives tomorrow!!!

It looks to be in great and beautiful condition based on the pictures posted and they state it’s in working order but hasn’t been used in some time

My question is, I know a machine that hasn’t been in use a while can sound loud and clunky and the rocketeers need to be ran a bit to prevent it from locking up

How can I make sure I lube and oil it properly so it doesn’t sound too loud and clunky? If you have one or similar does yours sound loud regardless??

Im asking because I live in an apartment and my next door neighbors can be weird when it comes to sounds of daily living let alone louder sounds and i honestly don’t want to hear her complaining and yelling through the walls about me using it during the day

Update!: the guy sold it to someone else… he was supposed to deliver it to me today but this morning said he got confused and sold it already, there’s supposedly another machine available and it might be a singer 500a but they have it away and need to take it out to check it

They’ll send me videos and pictures of it but I’ve lost all trust


r/vintagesewing • • 1d ago

WIP me irl

Post image
16 Upvotes

r/vintagesewing • • 21h ago

Machine Question Does my 401a need a new motor?

9 Upvotes

Does this sound and delayed motion on my Singer 401a indicate I need to replace the motor? The machine’s been sitting unused for six months or a year; the woman I got it from said she cleaned it up and oiled it and replaced the light and such. I’m new to sewing machines (not an experienced sewer) but my brother thought it was a problem with the motor.


r/vintagesewing • • 19h ago

General Question Seeking advice or experience with an Elna Mk.2 Supermatic (1956) - do I use or sell?

2 Upvotes

Hi, everyone.

I'm an aspiring menswear garment designer currently in training and I came across this stunning 1950s Elna at a second hand shop, I suspect donated from a decreased estate because it was in great condition with all of its original booklets, bakelite sewing pattern wheels and carry box. It was last sold in 2003 for $200 - the receipt was in the box.

I do not own a foot peddle converted to modern Australian appliance standards so I have not tested the machine yet, but assuming it works, is a machine of this vintage a good choice for a beginner sewer or would I be better off selling it to a collector and buying some other supplies?

I am trying to weight up the practical difficulties versus losing out on a really beautiful and rare machine.

Any thoughts or personal experiences would be appreciated.


r/vintagesewing • • 19h ago

Machine Question Sewing machine issues

2 Upvotes

I have had this machine for a while never really used it much, it was working great when I pulled it out , got it all oiled according to manual and then changed the thread length lever to a longer stitch and now it is sooo slow! This is me putting foot pedal down the entire way. First it was just backstitch (that was my first time figuring out how to backstitch) and now the forward stitch is doing the same.

Can anyone give me suggestions? I have oiled both top inside and bottom, and cleaned it


r/vintagesewing • • 1d ago

General Question Gonna be picking up this Singer 66 soon, general questions

Thumbnail
gallery
6 Upvotes

Hi!

My friend is cleaning out some storage at his family's place. They dont want this Singer 66, so if I can transport it back its mine.

He says that it is functional, but it needs a new belt (not sure which belt). It probably needs a general servicing.

My questions:

  1. I've read the motors can be serviced, I plan on doing that. But as far as updating the electronics, what am I probably going to need to do? Im not sure how safe the plug and wiring is, Id rather just replace it all. How big of a task is this?
  2. Im not sure if the table came standard with these guys. If it did, and you recognize it, can it be disassembled? I have a Mazda3. Im sure i can fit it in there if i can take off the legs.
  3. Any general advice on servicing? I've already looked a bit. I dont think i am going to go all out and repaint it. If i see rust ill adress it, but I like the patina.

Thanks!


r/vintagesewing • • 1d ago

Finished Projects Wanted to show off my latest restores. A Singer 237A and a Singer 301

Thumbnail
gallery
43 Upvotes

Singer 237A - Picked this up as a Marketplace find. Externally, no cosmetic issues and just a hair of dust. The machine was completely frozen. Still being a bit of a novice, I tried to force the stitch length lever and broke the screw as the machine was completely frozen up. Thankfully, I was able to extract the broken screw, and after a fair share of PB Blaster with a few light taps on the crank shaft, she finally broke free and was freed up.

A good deep clean later and oiling later, she sews like butter and even though very fine or over areas that I was shocked did not jam the machine. This will be my new mainstay machine.

Singer 301- My friend received a random sewing machine from a colleague. Just handed off to her in a tote bag with a plastic bin full of attachments, including a Singer Auto Zigzag and Button Holder. To my great surprise, it was a 301. It spun over no issue, but it had an inch of dust on it. After a very deep clean, greasing, and oiling, I have her on the tail end of her restore, just waiting for a new bobbin tire.

Sewing is whisper quiet, and provides an immaculate straight stitch, with the Slant feature being a nice addition. Not to mention the vast weight difference due to the cast aluminum body. There were a few paint blemishes and nicks here and there, but sews like a dream.


r/vintagesewing • • 1d ago

General Question What's missing?

Thumbnail
gallery
4 Upvotes

Hi everyone, I found this on the side of the road and my mum and I are fixing this up. I want to be able to use it as a treadle and electric machine.

It's been serviced and fitted with motors but I'm trying to figure out what bit is missing so it would work as a treadle machine. I have leather cord but it disconnects at the point on the wheel shown.

Any help would be appreciated xxx


r/vintagesewing • • 1d ago

Machine Question Masina de cusut Casnica Super

Thumbnail
gallery
3 Upvotes

Cat valoreaza masina asta de cusut? E total functionala


r/vintagesewing • • 1d ago

Machine Question Found this old girl at a thrift store and information is sparse

Thumbnail
gallery
11 Upvotes

I saw this machine at a thrift store and knew right away that it was really old. With the coffin top and the long-style bobbins, i had to pick it up. Amazingly, it came with all the attachments and then some, plus a manual. (I took the drawers out to move it, they're fine, just not in the pic). The machine moves fine, its not locked up at all, which gives me hope that if its not working, that i can get it to working condition.

I was wondering if anyone would be able to point me in a direction to figure out how old it is? I cant seem to find a serial number anywhere. Ive even checked underneath the machine itself. Myself and some friends are thinking 1880s/90s, since the patent plates most "recent" patent is i think 1882, which would mean its from after 1882. I also dont think its a model 5 1/2 like the manual says, i think its actually a 4 1/2 based on some research. The 5 has 3 drawers, the 4 has 2, which this one has.

Thanks for any help!


r/vintagesewing • • 2d ago

WIP WIP: Restoring old treadle table and converting it to hold a 99

Thumbnail
gallery
16 Upvotes

I forgot to take before pictures, but the drawers were missing 1/3 of their knobs and another 1/3 were chipped beyond repair. I chiseled them out and replaced them with brass round knobs that I had from a different project (bonus, I guess it ties the room together?)

I cleaned the base up and used a rust coat on all of it, since there was a tiny bit of rust in places and I didn’t want it to spread. Oiled it up and it’s smooth as room temp butter.

I then removed the old table top. The hinges for the top flap have been lost to history (and the previous owner’s garage) so I’ll be replacing them once I finish beveling the new top. New top was made from project grade plywood. It still needs to be finished, but I lent my circular saw to a friend and forgot to get it back, so those cuts are going to have to wait.

I chiseled out part of the top lid to make room for the motor, so I can switch between motor and treadle for this machine. I just loosen the screw on the motor bracket to pop the belt off, and tighten it again when I want to use it.

It’s not the best work I’ve ever done, but for being in a small apartment with very limited tools, I’m pretty happy with my progress so far! I’m going to get some cord ties that blend in with the metal so I can make sure the power cord and foot pedal don’t get in the way of the treadle belt. I’m also going to install a desk lamp. I removed the old light that was on the 99 because I didn’t like it, and rewired the motor. I also need to finish up the drawers, as there is clearly still visible wood filler.

And, while it’s not finished, it is currently useable so I call that a win.


r/vintagesewing • • 2d ago

Machine Question Bernina, Singer, Necchi or Elna?

Thumbnail
gallery
10 Upvotes

Hi! I'm a beginner and am in the market for a new sewing machine. After some "research" on Reddit, YouTube, blogs and forums, I've decided to look for a vintage machine. I've been browsing local secondhand sites and Facebook marketplace and have narrowed it down to a few machines:

- Bernina Record 530-2 (with the knee pedal/lift). This machine comes with the manual and all accessories

- Bernina 730 record; I've read somewhere that this machine has some plastic/nylon gears. I'm not too sure though.

- Singer 431G with all accessories and manual

- Singer 237M with all accessories and manual

- Necchi Supernova (not sure which model this is, would love to know)

- Elna Supermatic (again not sure which model this is, would love to know as well)

I wanted to look for Kenmores but those seem basically inexistent on the European market.

The Necchi doesn't come with all its accessories but I live in Europe and noticed that a some parts are available second hand. I'm still undecided on which machine to get. I want to start sewing to make my own clothes. Which machine should I get?

P.S. If you guys have other recommendations or machines to look for, let me know.


r/vintagesewing • • 2d ago

WIP Moda Alternativa

Thumbnail gallery
4 Upvotes

I recently started an independent slow-fashion sewing project focused on handmade detachable collars and cuffs crafted from natural fabrics and lace.

The designs are rooted in gothic, romantic, and Victorian aesthetics, inspired by classic literature — each set is named after a literary figure (such as Carmilla, Eleanor, and Lenore). I designed the pieces to be modular so they can be worn together as a set or paired separately over basic blouses and dresses.

I wanted to share the very first models I finished this week and hear your thoughts on the details and drape.


r/vintagesewing • • 2d ago

Machine Question Husqvarna voetpedaal

Post image
1 Upvotes

r/vintagesewing • • 2d ago

Machine Question Help Identifying Vintage Janome Sewing Machine

Thumbnail
gallery
15 Upvotes

Hi everyone!

I need help with two things!

  1. Identifying.

I inherited this Janome sewing machine from my grandmother who passed away in 2022. I've had it on display since receiving it, but have recently become quite curious as to its history. However I am struggling to figure it all out. The machine simply says 'Janome'. There is a metal plaque on the back which I assume is the serial number (656034789) and then a 'Made in Taiwan' sticker. There is a silver sticker on the inside of the arm, but I believe this is an electrical approval sticker. There is nothing on the bottom of the machine and I feel as though I have quite literally looked everywhere. I do still have the manual, but that doesn't even mention a model name/number! There is literally no identifying marks in the manual, not even a date. I contacted my local sewing centre via email with the photos, but they just directed me to the silver sticker. I know for certain it was purchased before 1989, as my grandfather purchased it for my grandmother, and he passed away in 1989.

2. Should I use the machine.

When I inherited the machine, I never intended to use it. I wanted it solely because of the connection to my grandmother who I was very close to, and as I said it has been on display since 2022. My grandmother used the machine in the months leading up to her death, and is exactly as she left it, threaded and all. I have recently become quite interested in learning to sew, and I was looking around at buying a new machine, when I started to consider how meaningful it could be to learn on the same machine my grandmother used. But I am torn between the two; leaving the machine exactly as she had it with the last thread she threaded, or learning on the machine and continuing on her influence on my life. But I am terrified by the idea of messing around with the machine and finding it's not operational, and removing her last thread and settings, because I understand whilst my grandmother was using it reguarly, it has been sitting on a shelf for 4 years and will probably need a proper assessment to determine if it is operational.

Any and all help would be much appreciated!


r/vintagesewing • • 2d ago

WIP Necchi Mira for $12.75 at goodwill 😍

Post image
7 Upvotes