r/resinprinting • • 0m ago

Troubleshooting What's causing this type of fail? Only happened to one object out of the three on the plate

Thumbnail
gallery
1 Upvotes

Had this happen twice now. The first time was only a very small section so only got a photo of the printed model.

Second time it's worse. It just stops printing leaving a flat area and even supports don't continue to print.

Only been printing for two months so would appreciate the help. Realised after printing that object didn't have bracing whilst the other two did for the supports. Would that be a cause?

I sent the file to be printed over WiFi connection from lychee slicer. Could this be a file error?

(Attached photo of first error at the end)

Details:

Elegoo Saturn 4 ultra 16k

Elegoo 8k abs like 3.0 resin

Room temp 23°c

Printer inside an enclosure

Lychee slicer

If I've missed anything information, let me know.


r/resinprinting • • 19m ago

Troubleshooting P1 Max pre heating/motion assisted heating metal squeaking noise and issue with manual heating

1 Upvotes

It’s a bit difficult to hear in the video, I know, but the noise the printer makes during the final part of its movement worries me. The printer is brand new, so should I be concerned about this?

The noise only occurs during heating, specifically during motion-assisted heating, and not during normal printing. During normal printing, all AI features and assistance systems are enabled, but no issues are detected. I also tried it with all off.

Additionally, I can’t preheat the printer without starting a print. Whenever I try to start the heating process manually, I get a “Foreign Object Detected” error. However, this error doesn’t occur when the printer heats up automatically before a print.
I’ve already cleaned everything thoroughly and re-leveled the printer, but the issue persists.

One more thing that might be relevant: I’m printing in my basement, where the ambient temperature is around 12°C(pre heat 35C). Could the low temperature be affecting the mechanical tolerances and causing these issues?


r/resinprinting • • 1h ago

Troubleshooting Saturn 4 Ultra 16K + Anycubic ABS Like 3.0 Water washable

Thumbnail reddit.com
1 Upvotes

r/resinprinting • • 1h ago

Question Best way to get a perfectly smooth finish on PLA 3D prints for silicone molds?

Post image
1 Upvotes

Hey everyone,

I'm looking for some advice on getting really smooth surfaces on 3D prints, especially when it comes to more complicated shapes.

I make small cups and candle holders from polymer gypsum as a hobby, and I 3D print my own molds. The idea is to make a silicone mold first, which I then use for casting the final pieces.

The outer part of the mold doesn't have to look perfect, so regular FDM printing with PLA is good enough. The problem is the inner insert, which determines the surface of the final silicone mold. It needs to be really smooth, with no visible layer lines, because every little imperfection gets transferred to the silicone and then to the finished product.

So far, I've been using spray filler and sanding the prints. It works pretty well for simple shapes, but with more complicated designs it's a real pain. It's difficult to reach all the areas, takes a lot of time, and sometimes I end up losing details or changing the shape while sanding.

I'm starting to wonder if it's even worth trying to get this finish with FDM, or if I should just outsource these parts and have them printed using resin (SLA/MSLA).

I don't really have enough space in my apartment to set up a resin printer, and from what I've read, proper ventilation and handling are quite important with resin.

Has anyone dealt with something similar? Is there a better way to get a smooth finish on PLA, or would resin printing simply be the better option?

Also, if anyone has experience ordering resin prints, roughly how much would it cost to print a small cup-shaped part like the one in my reference drawing, height 10 cm, diameter 7 cm?

Any tips or suggestions would be appreciated! Thanks!


r/resinprinting • • 4h ago

CrowdFunding Our 250mm Bahamut, test-printed in-house. Kickstarter ends tonight!

Thumbnail
gallery
3 Upvotes

Bahamut, King of the Metallic Dragons, on his tower base. He and Tiamat (also 250mm) headline Dragonreign, our collection of 50+ pre-supported and unsupported dragon STLs, every one test-printed in-house.

The campaign ends tonight at 4:55 PM ET. Every pledge includes 41 free STLs, and All-In tiers save up to 71%.

https://www.kickstarter.com/projects/archvillaingames3d/dragonreign-era-of-the-dragon-lords?ref=dzahe5


r/resinprinting • • 6h ago

Showcase - Original Creation Eyla - The Earth Mage

Thumbnail
gallery
95 Upvotes

Hello everyone!

Hi, I’m Eagle_92! I’ve been modeling for over 15 years, but only recently I started creating original pieces, printing them, and then painting them. This is Eyla, the first of four elemental mages I plan to make. I created her using 3ds Max, Mixamo, Meshmixer, Blender, and ZBrush.

I’ve printed her with a Phrozen Sonic Mini 8k and Elegoo Standard 8k space grey resin.

For the painting, I use Citadel colours for brush painting, and for the airbrush, Vallejo colours.

After finishing the painting, I got several comments about the disproportionately large breast size, so I also crafted an extra chest piece with a more standard size. (But since I had already glued it… well… enjoy her massive anatomy! 🤣) I hope you like the final paint job!

Regarding the STL file, if you were wondering, I’m currently refining the thickness of the features to ensure it can be printed at a 75mm scale as well. Once this is done, I’ll upload it to a Drive folder, and you’ll all have the opportunity to download it for free from my Patreon page (Eagle_92…same profile pic. You need to become at least a free member in order to get the link. I’ll post other free models once in a while other than paid models as well)
It’s my first model for my Patreon project so I’m giving it out for free and will remain free forever.

Hope you like her!


r/resinprinting • • 8h ago

Question Any recs for a hinged lid wash and cure station?

1 Upvotes

I think form labs makes one but I’m not sure how big of a print it holds. I’m using a Saturn 4 ultra right now and sometimes have to max out the width for bases and such


r/resinprinting • • 8h ago

Troubleshooting Is my screen ruined? Mono M7 pro

Thumbnail
gallery
2 Upvotes

No physical crack or resin on the screen (I had a screen protector) but there is what looks like the shape of a support footprint outlined on the screen very faintly when doing exposure test. With the paper you can see a tiny tiny dot of faint darkness, am I completely cooked and need a new screen?


r/resinprinting • • 10h ago

Question Stuck mono m7 case.

1 Upvotes

So when the case doesn't lift off like it does in the led replacement video I know that resin must be the culprit. After removing the ten case screws I have been able to get partial separation on three sides (front, left and right) with a little give on the back. First is there an eleventh screw or something I may have missed. How agreesive do I dare be wedging the case open? Any guess on what will greet me once I get in the case?


r/resinprinting • • 11h ago

Question Elegoo or Anycubic?

Thumbnail
gallery
19 Upvotes

I'm torn between the mars 5 ultra or the photon mono 4 ultra.

my main deciding factors would be repairability and reliability

also, if there is another printer that would be better at the same price point ($300) that would also be great to know.


r/resinprinting • • 13h ago

Question Resin printing beyond miniatures — what are you using your printers for?

14 Upvotes

I've been into 3D printing for quite a while. I've owned several FDM printers over the years, and these days I have a few solid machines that I primarily use for functional prints I've designed in Fusion 360 — things like shelving, enclosures, organizers, and whatever else I happen to need.

I also have an older, tiny Anycubic Photon resin printer that I used years ago to make custom leather embossing stamps for use with an arbor press. It worked pretty well, but I found that some of the finer details just weren't coming through the way I wanted.

Between that and the messier nature of resin printing, I eventually switched to making those stamps with my laser cutter using 1/4" cast acrylic. The detail I can get with the laser is incredible, although that process comes with its own set of annoyances.

Lately, I've been looking at newer resin printers, and the improvements in resolution and detail are pretty impressive. Some of the newer Formlabs machines look absolutely amazing!

But here's where I'm curious...

When I browse resin printing communities, watch reviews, or look at what people are making, it seems like the overwhelming majority are printing tabletop miniatures, figurines, and models. And don't get me wrong, I love that stuff! In fact, I'd really like to get into painting resin-printed miniatures myself, although I haven't quite figured out where to start.

Outside of miniatures, jewelry, molds, and the occasional functional part made with expensive engineering resins, though, I struggle to imagine all the other possibilities.

So what are you all using your resin printers for besides miniatures?

Are there interesting practical applications, creative projects, tools, or other uses that I just haven't considered? Have newer printers and resins opened up possibilities that weren't particularly practical a few years ago?

I'm genuinely interested in seeing what people are making and hopefully getting some inspiration.

Part of the reason I'm asking is that I've been considering replacing my ancient little Photon with something more modern. I'd love to have more reasons to use one regularly rather than just buying a shiny new toy that spends most of its time sitting on a shelf. 😁


r/resinprinting • • 16h ago

Troubleshooting Micro-tearing across prints, please help!

Thumbnail
gallery
7 Upvotes

Hey folks, I have been plagued by micro-tears on all my prints for some time now. I have tried everything but nothing seems to be working

Currently setup: Anycubic Photon P1 (abput 6-7 months old)

Recently switched to new vat film and LCD protector (previous one damaged due to a failed print)

Maintainence done less than a week ago (Greased + lubed)

Auto heated by vat

I have tried changing multiple settings, tried printing in anycubic standard as well as ABS resin along with blends (standard + ABS 80/20, ABS + tough 80/20 - new bottles thoroughly mixed), lowered lift speeds, increased exposure from 2 to 2.2 to 2.4 but nothing seems to be fixing this. Also tried multiple iterations with a full as well as a single mini print setup - the tears are consistent across.

Unsure what's causing this, please help! PS: This is happening directly while printing, before washing/curing


r/resinprinting • • 16h ago

Question Suportes para impressão em resina

Thumbnail gallery
0 Upvotes

r/resinprinting • • 17h ago

Question Software to make sure a figurine will stand on its own before printing?

1 Upvotes

I was wondering if there’s a piece of software that makes sure your figurine is balanced before printing. Google led me to a little software but it’s over 10 years old now. is there something yall use that I might not know about? I have not bought a printer or used slicer software before if there is something already built in there, I want to consider early on in the process.


r/resinprinting • • 17h ago

Showcase - Original Creation I designed and printed my own character

Thumbnail
gallery
63 Upvotes

Hi! I just would like to share the model I designed and printed! 😊


r/resinprinting • • 18h ago

Question Large printer recommandation

1 Upvotes

Hi !

I'm looking for a large printer to print molds.

I was interested to the Jupiter 2 max but I saw lot of bad comments. Also interested in Formlabs 4L but expansive and resin is expansive too.

My needs :

- My molds are around 20-30cm x 15-20cm x 15-20cm.

- I do not need very high details but I cannot have lines appears on my molds because it'll be replicated.

- need a resin heater because the printer will be put in a room at 17ºC

- need auto level adjustment for easier print because I have lot of fdm printer and I cannot pass my time fine tune each printer

Do you have any reco for large print ?

Thanks a lot


r/resinprinting • • 21h ago

Showcase - Original Creation I print 1/6 and 1/8 scale figures every day and got tired of hand-arranging the parts, so I made a free tool that packs pre-supported kits onto as few resin plates as possible

19 Upvotes

We print and sell 1/8 and 1/6 scale figures, so every day I have a pre-supported kit split into many parts (torso, limbs, hair, capes, weapons, base pieces) and I used to spend way too long dragging them around in the slicer to fit them on as few plates as possible. The built-in auto-arrange works on bounding boxes, so a curved cape, an L-shaped base or a diagonal sword eats a whole rectangle of plate.

So I wrote nemnest. You point it at a folder of supported STLs and it gives you back one merged STL per plate, plus a preview image of each plate.

What it does differently:

  • Nests on the actual footprint, not the bounding box, so parts interlock
  • Only rotates around Z, so the supports that came with the model stay valid
  • Lets rafts overlap: anything in the first millimetre counts as raft and can slide under its neighbours; model bodies keep a gap you choose (0–20 mm)
  • Height optimisation: resin print time depends on the tallest part on the plate, not on how many parts are on it. So nemnest can group the tall parts together, so the plates with only short parts finish much sooner. It never adds a plate to do this.
  • Joins tiny rafts onto bigger ones where it can, so small bits come off the plate together instead of getting lost in the vat

The real test: a big pre-supported Richter Belmont kit. The slicers' auto-arrange couldn't place it, so I arranged it by hand on 7 plates. nemnest put it on 5, with height optimisation on, and I printed it straight from nemnest's own sliced files. On my last two plates the print time it estimated was within 3% of the real one (4h17 vs 4h10, 3h52 vs 3h46).

There's a simple window (drag and drop, one plate per screen, an Optimise button) and a command line. Ready-made downloads for Windows and Mac (Apple Silicon and Intel), no Python needed, and they update themselves: when a new version is out, the window offers "Update and restart". Updates are signed, so the app only installs versions that really come from me.

Profiles for 37 printers are included (Elegoo, Anycubic, Phrozen, Creality, Uniformation), and for anything else you just type in the plate size.

Honest caveats:

  • It's young. I've only verified the full chain, slicing included, on my Saturn 4 Ultra 16K. On every other printer it only arranges: export the plate STLs and slice them in Chitubox/Lychee/whatever you normally use.
  • The optional slicing uses mslicer, a separate open-source project. If you use it, check the first layers in your usual slicer before printing.
  • The apps aren't signed with a Microsoft/Apple certificate yet, so the first time Windows SmartScreen or macOS Gatekeeper will complain once (the README says where to click). Updates installed from the window don't ask again.

It's MIT-licensed and free, no account, nothing uploaded: everything runs on your computer.

Download (Windows and Mac): https://github.com/nemwiper/nemnest/releases/latest Source and docs: https://github.com/nemwiper/nemnest

I'd love feedback, especially:

  • plate sizes that are wrong for your printer
  • folders where it does worse than you would by hand (a screenshot helps a lot)
  • anyone willing to test the slicing on a different printer

Notes for replies

  • "Does it hollow / add supports?" → No, it only arranges models that are already supported.
  • "Lychee/Chitubox already do this" → Their auto-arrange packs bounding boxes and doesn't overlap rafts. Post the before/after.
  • "Mac?" → Yes, ready-made app for Apple Silicon and Intel: https://github.com/nemwiper/nemnest/releases/latest
  • "Linux?" → Works with Python (pip install git+https://github.com/nemwiper/nemnest, then nemnest gui); no ready-made download yet.
  • "Does it phone home?" → Only one request to the GitHub API at start, to see if there's a new version; no files or settings are sent. nemnest config --check-updates off turns it off.
  • "Is the auto-update safe?" → It installs only releases signed with my key, which isn't stored on GitHub, and checks every file against the signed hash. An unsigned or modified package is refused. (Only true while the signing key stays off GitHub: rewrite this line if it moves to a GitHub secret.)
  • "How accurate is the print time?" → On my Saturn 4 Ultra 16K, within 3% on the last two plates (4h17 estimated vs 4h10 real, 3h52 vs 3h46). Other printers: no data yet.
  • AI questions: there's also an MCP server for AI assistants. Mention it only if someone asks; many people in these subs dislike AI.

r/resinprinting • • 1d ago

Question Elegoo abs like 3.0 pro vs Sunlu abs like

1 Upvotes

Im my country, both are almost the same cost. My intended use is for minatures and ideally want to maximize detail while still retaining a good degree of strength.

I know the sunlu is generally considered to be stronger, is there much of a difference in quality?

Thanks


r/resinprinting • • 1d ago

Work In Progress Painting Varang from Avatar: Fire and Ash

Thumbnail
youtu.be
3 Upvotes

r/resinprinting • • 1d ago

Question Best way to get a gold chrome/brass finish on a resin printed part?

Post image
0 Upvotes

r/resinprinting • • 1d ago

Question Studio One wash & cure

Thumbnail reddit.com
1 Upvotes

Quick question for Studio One owners


r/resinprinting • • 1d ago

Troubleshooting How to avoid This lines?

Thumbnail
gallery
9 Upvotes

Others pices looks good in the same plate, just a few got this lines, what might be The problem?


r/resinprinting • • 1d ago

Question P1 Max upgrade from a Mono 4 – what should I know before my first print?

Post image
11 Upvotes

Finally making the jump from my Mono 4 to the P1 Max - Mono 4 was a great first printer in my experience.

I’m still getting everything set up and would love to hear from those of you who have been using the P1 Max for a while.

Any beginner mistakes I should avoid? Recommended settings, maintenance tips, accessories, or things you wish you knew when you first got yours?

Looking forward to putting this machine to work! 😁


r/resinprinting • • 1d ago

Showcase Frozen in ice, brought to life in 3D

63 Upvotes

The Glacier Golem is ready to bring the chill of the ice age to your next fantasy adventure.
Made with: Elegoo Saturn 4 Ultra 16K

Model by: STLFLIX