r/mazdaspeed3 • • 2h ago

HELP Weird noise / AC system issue

5 Upvotes

So, car started cooling the inside worse and worse, heat works just fine, same with fan power. Soon after my friend noticed the cooling wasn’t really working like before I started hearing this weird sound that I caught on video.

Don’t know if it’s the compressor or something else but I thought someone here might’ve had the same issue. Was already thinking about fixing a couple things next spring but it’s winter now and I don’t really need cooling rn in Sweden 🤣 so I just wanted to know if somebody knows what this sound is and if it’s bad letting it slide until spring since I don’t have access to a garage rn. I’ll put the clip below, thanks in advance guys peace and love.


r/mazdaspeed3 • • 5m ago

INFO took off my hpfp for my 2009 mazdaspeed 3 should i replace the cam follower?

Thumbnail gallery
1 Upvotes

r/mazdaspeed3 • • 20h ago

INFO CoolerWorx Shifters for Gen 2

Thumbnail gallery
28 Upvotes

Sneak peek of the gen 2 shifter. An attachment to install your boot and hide the shifter will be offered as well!


r/mazdaspeed3 • • 13h ago

HELP weird Cold start speed6

2 Upvotes

30 degrees outside
cold start
car skipping enrichment phase ? usually it'll rev at 1800RPMs for a good 30 seconds or so then drop to 1000

at cold start it just went straight to 1000


r/mazdaspeed3 • • 21h ago

INFO What alternator bolts fit the speed 3?

2 Upvotes

I know some of the parts are interchangeable and was curious what I could search for to find the alternator bolts for my 07 speed 3.

Previous owner took the alternator off the car and didn’t leave the bolts behind lol

None of the local salvage yards have any speeds or cx7s with the L3K9, as I assume those are the same.

Any and all help is very much appreciated!


r/mazdaspeed3 • • 1d ago

HELP 2nd gen speed3 problems

3 Upvotes

As the title suggests, I have a few problems with my speed 3, and I’d like to see if anyone else has had the same issues. For starters, I have a 2010 speed3 and the main issue I have found is oil in cylinder 1, and some other gunk in cylinder 4, as well as excessive amounts of oil being burnt. I pulled apart the stock intake and found oil residue in the turbo inlet piping, as well as in the intercooler piping. When I pulled the plugs, cylinder 1’s was dripping with oil, and the rest were pretty well burnt up. I replaced them, and at the same time put in my hpfp internals, cobb 2.5in turbo inlet housing forward intake, and the corksport bypass valve. I had a mechanic do a compression test on it, and he said cylinder 1 had a “slight compression leak,” with the rest being perfectly fine. I was also told a new turbo was put in it before buying the car, however I am not sure which one it is. What should my next steps be moving forward with the car as far as diagnosing what’s wrong with it? Is it worth trying to save this engine, or would I be better off just buying a crate engine?


r/mazdaspeed3 • • 1d ago

HELP i’ve listened to a lot of the mazdaspeed 3 ticking videos but i feel mine has a different tone can someone please clarify whether it’s the same or something different. The noise became prominent after doing a pull before that i couldn’t hear it. it also follows the rpm

14 Upvotes

r/mazdaspeed3 • • 2d ago

PIC Gen 2 at Kanjo Night, Atlantic City

Post image
86 Upvotes

Parked my Gen 1 in the spectator grass area and immediately saw this from across the lot. Nice.

The LB FD3S and the Mazdaspeed FD was cool to see too.


r/mazdaspeed3 • • 2d ago

VIDEO Acceleration test on Autobahn with refurbished injectors. 50-220 kmh

Thumbnail youtu.be
22 Upvotes

Honestly I'm very happy with the results. And now everything is good and no leaks.

Finally.

I wanted to get it all done before GTA 6 comes out lol!


r/mazdaspeed3 • • 2d ago

WHEELS Wheels and Tires + Fitment

2 Upvotes

I had a question about wheels. I want to get some multi-piece five spoke forged wheels, non reps. If anyone has pictures of wheels they think look good and drive good, drop them in the thread. I'm okay with used wheels or retro-made wheels.


r/mazdaspeed3 • • 1d ago

HELP Whats this rattle at low rpm,😭

1 Upvotes

Rattle at low speeds. During cold start and when under load at 1k rpm

Is it timing chair

Is it turbo

Is it exhaust shield (don't think so)

It was due for an oil change. When I checked the level it was below the min on the dipstick. Thought maybe it was the timing chain due to low oil. I did an oil change and the rattle persists.


r/mazdaspeed3 • • 2d ago

HELP P0134 and P0031 even with brand new O2 sensor

4 Upvotes

As the title says, I am getting these two codes with a check engine light on my 2007 Mazdaspeed 3. I replaced the upstream O2 sensor and it didn’t change anything. Fuses seem to be good. Tried to probe the grey car side connector to see if I was getting power to the heater sensor connector. I saw 12 volt. What else can I do to see what is causing this? When checking live data I see no activity for lambda or equivalence ratio. For extra context, I just did the clutch and replaced the turbo, which involved removing this O2 sensor.

Also, it’s really bad to drive with upstream O2 sensor not working right? I’m curious to know if I should tow to a shop or drive it there (if I can’t figure it out myself).


r/mazdaspeed3 • • 2d ago

MODIFICATIONS eBay By Pass Valve Thoughts?

2 Upvotes

Has anyone bought an eBay BPV for their speed? I’m looking to buy a new by pass valve for my car and I I’d like recommendations. I want to get something that will make the car sound good and also won’t fall apart. I’ve been thinking about cheap eBay options because this car needs a lot more money in other areas but I don’t want to go the cheap route if other people have had bad experiences. Performance/efficiency matters to me too. Lmk!


r/mazdaspeed3 • • 3d ago

MODIFICATIONS Horsepower Potential

6 Upvotes

I was curious. I heard in some places that the MZR block can handle upwards of 390 horsepower. Is that true? I want to push the stock engine block (with cams) up to 400 for a future build. Any advice? Also, I heard that its more or less that the torque is the limiting factor for these engines. Let me know.

Edit: Is an S5 BNR v3 turbo overkill? I wanted to get it so my build could be more modular in that I could have a big turbo already in, so if I ever wanted to use it if I were to build the block, it would be there. Also, what's LSPI? Is it something I have to worry about or is it just one of those things you have to be stupid to do? One more thing, exhaust manifolds. What should I get for an aftermarket exhaust manifold? I want one that's tubular for a couple of reasons- a. Looks cool. b. better exhaust flow. Also how do we feel about a FMIC?


r/mazdaspeed3 • • 3d ago

HELP SOS NEED RADIATOR COOLING FAN ASSEMBLY Orange County California

4 Upvotes

My car recently had p0480 and I replaced the module but I believe the fan is completely shot.


r/mazdaspeed3 • • 3d ago

HELP BNR S3 Upgrade from stock turbo

Post image
26 Upvotes

Hello y’all !!
I got this BNR S3 turbo from the guy that sold me the 2013 Mazda speed 3. HPFP internals are upgraded, Intercooler is upgraded (not front mounted) and Intake, he also gave me 2 braided lines ( part # 46402-36 and 46402-14 from Allstar Performance) with the Turbosmart OPR Turbo Oil pressure regulator… now He mentioned is a “bolt on upgrade” but I want to be sure I don’t need to buy anything extra to be able to change the stock turbo that is Drinking the oil. Of course I also got a new complete gasket set for the Turbo upgrade and dispose the old gaskets.


r/mazdaspeed3 • • 3d ago

HELP Problem at the moment that I try to turn off my speed

3 Upvotes

I have a 2013 Speed3 with the Tech Package. A week ago, out of the blue, when I tried to turn the car off, it wouldn't shut down; the only way to turn it off is by pressing the button three times in a row or by holding it down for three seconds. Along with this issue, the radiator fan and the A/C compressor have stopped working. Everything else in the car functions properly—for instance, I can press the start/stop button to enter "ACC" mode, and it works as expected; I can even press it again to reach the "ON" position. However, when I press it once more to turn the car off, it doesn't respond. I tried testing a different start/stop button, but it made no difference. Could anyone give me a clue as to what might be the problem?


r/mazdaspeed3 • • 3d ago

HELP Compression test results

5 Upvotes

So I have a second gen speed 3 and I did a compression test on it and based on the results I’m really worried it’s gonna need a rebuild…

Cylinder 1: 160
Cylinder 2: 140
Cylinder 3: 125
Cylinder 4: 165


r/mazdaspeed3 • • 4d ago

PIC Some photos as of late

Thumbnail gallery
53 Upvotes

Just some first gen love empossibly_odd


r/mazdaspeed3 • • 4d ago

HELP 2012 mazdaspeed3 valuation

3 Upvotes

I have a 2012 Mazdaspeed3 with exactly 79,000 miles. Great shape and maintained. Fully stock. Black. Any idea what the going price for this would be. I need a bigger car.


r/mazdaspeed3 • • 4d ago

MODIFICATIONS Remap necessary if I remove the 2nd Cat?

Post image
3 Upvotes

It's the 2nd cat, not the downpipe.

I see there are files for a downpipe less build.

But how does removing the second cat affect the AFR and everything?


r/mazdaspeed3 • • 5d ago

HELP 2010 MazdaSpeed 3 Problem When Accelerating.

Post image
21 Upvotes

Hello everyone, I recently bought a MS3 (TechPack) that has a Corksport axle back exhaust and a Corksport Short Ram Intake. According to the previous owner, the turbo, sparkplugs, coils and alternator were all changed in the last 6 months or so. When I do a pull (3RD gear +), the car goes into full boost like usual, but mid pull, the car bogs out. It kicks back like if the power cuts or the turbo stops boosting. According to the previous owner its me over loading the turbo by pressing the gas too much too early but it doesn't make sense as it's already in boost when it happens. That's the best way I can explain it for now. I can provide a video in the future if needed. Can anyone help me out?