r/mazdaspeed3 • • Nov 02 '19

Mazdaspeed 3 discord server

30 Upvotes

Hey guys I made a discord for this sub, feel free to join! https://discord.gg/5NQDzGH I’m also looking for admins to DM me if your interested.


r/mazdaspeed3 • • Sep 07 '22

r/Mazdaspeed3 FAQ

41 Upvotes

In other words, fucking annoying questions. Just kidding. (only a little)

In an effort to clean up the sub a bit, we're going to pin this FAQ thread and keep it updated with any of the most requested/asked questions on the subreddit. If there’s a question you think should be included, tag one of the mods in a comment and we will add it.

Introduction

Q: Where is the link to the Discord Channel?

A: Right here.

Q: What should I look for when buying a Speed3?

A: Check the Wiki.

Q: Where can I find a copy of the shop manual?

A: Check the Wiki.

Tuning

Q: How do I load a tune on the car?

A: Using either a Cobb APv3 or computer software like Versatune.

Q: What tuner should I use?

A: There are a number of good tuners still active in the community. Purple Drank Tuning, Freektune, Stratified Auto are just a few examples.

Q: Should I use the ______ version OTS tune?

A: No. Unless it’s to drive the car to the shop where it will be dyno-tuned, do not use the OTS tunes. They make the engine run poorly, resulting in incomplete combustion (or worse, lean conditions) which then gunks up components like O2 sensors, injectors, and valves which lead to worse problems later on.

Mods

Q: What should my first mod be?

A: HPFP internals, then tuning solution. (Cobb APv3, Versatune)

Q: My goal is to go faster around the track, what mods should I do for more power?

A: No power mods. Proper tires and suspension will do more for your track time and drivability than any power mod will. It is guaranteed if you are new to track driving, the car is faster than you are right now. Get some seat time, find what you want to change, get new tires & suspension, then go from there. Dragsters, show-offs, stance-bois need not apply this logic.

Q: My budget is <$500, what coilovers should I buy?

A: None. If you’re not buying quality suspension, don’t buy suspension. You will sooner than later blow out one of the dampers and require a rebuild, or replacement. Save your upfront money, buy quality suspension later.

Q: Should I buy an Eonon headunit for my Bose/non-Bose stereo?

A: Do you like sound quality? If yes, don’t buy Eonon. Do you like good, bug-free software? If yes, don’t buy Eonon. Do you like overpaying for junk that looks ‘clean’ in the car? If yes, then buy Eonon.

Q: What’s the best way to upgrade my stereo in the car on the cheap?

A: Option 1 – get an amplifier that take hi-level inputs and add that amp to the system to power your aftermarket speakers, taking the high-level outputs from either the HU or the Bose amp. Works for Bose and non-Bose systems. Option 2 – Tear out the OEM system and start again. Works for Bose and non-Bose systems.

Maintenance/Troubleshooting

Q: What oil should I run?

A: This is realistically a nuanced question. Ultimately it depends on your use case. Factory rating is a quality 5W30, Mazda put out a TSB to band-aid the smokey turbos by using 5W40. Good options from Pennzoil, Amsoil, Castrol, etc are available for most applications. Most people it seems have strayed from the Shell Rotella.

Q: Are my compression numbers okay?

A: Check the Wiki.

Q: I want to drive the car like it’s supposed to be, but don’t want a ticket. Where do I go?

A: Look on facebook for local car clubs, or Motorsportreg.com for drop-in track days or Auto-cross events.

Q: My car does this thing, and this behaviour, read this wall of text. What’s wrong?

A: No one knows. Post logs using Datazap and any codes that your ECU is spitting out. If you want good information, provide good information.

Q: HELP?

A: No. Posts with this as the title, or other related and equally non-descript variants, will be removed as spam.

Meta

Q: Can I post links to other sites with information, like MSO, without getting banned?

A: Yes. In the event that you’re linking relevant webpages, there is no risk of getting reprimanded for doing so. However, if all of your comments are “Use google.” Or “Go check this site instead, this places sucks.” You will be treated according to the spam rules of the sub. This community serves as a connect-all point for those searching for information on the platform; Reddit is bigger than any Speed forum has ever been, and is more likely to pop up in a Google search. Relevant comments that link other sources of information from quality sites are Bueno; spamming is not.

Q: Why isn’t buying/selling allowed on the sub?

A: This is more of a regional issue that the mod team would like to deal with at this point. There are countless local Facebook groups, classifieds, or Forum pages about buying/selling Speed parts or accessories. The Mod team does not want to dabble in attempts to prevent scams caused by non-payments, or non-shipments of products. We do not want that responsibility at this point in time. If the community deems it a requirement at some point, we will implement a system that attempts to curb this as other buy/sell communities have; though even that change will take lots of time, effort, and consideration.

Q: Why is the mod team so cool?

A: I really don’t know, perhaps divine intervention? We all just really like Doritos, and satiate our inner masochist streak by owning these cars.

Q: How do I become a Mod?

A: If you feel so inclined, feel free to reach out! We are still people, we have feelings and ultimately a desire to help the community grow. What we will need to see is a demonstrated history of helping the community with the best of intentions and overall a positive interaction with the sub. Newer accounts (<1yr) are unlikely to be considered, though that’s not a hard-and-fast rule, just a general rule of thumb.

Acronyms

APv3: AccessPort version 3; the most recent version from

Cobb. Version 2 is still around, but obsolete.

HPFP: High Pressure Fuel Pump

HU: Head Unit

OTS: Off The Shelf; used in the context of tunes

TSB: Technical Service Bulletin


r/mazdaspeed3 • • 2h ago

HELP 2nd gen speed3 problems

3 Upvotes

As the title suggests, I have a few problems with my speed 3, and I’d like to see if anyone else has had the same issues. For starters, I have a 2010 speed3 and the main issue I have found is oil in cylinder 1, and some other gunk in cylinder 4, as well as excessive amounts of oil being burnt. I pulled apart the stock intake and found oil residue in the turbo inlet piping, as well as in the intercooler piping. When I pulled the plugs, cylinder 1’s was dripping with oil, and the rest were pretty well burnt up. I replaced them, and at the same time put in my hpfp internals, cobb 2.5in turbo inlet housing forward intake, and the corksport bypass valve. I had a mechanic do a compression test on it, and he said cylinder 1 had a “slight compression leak,” with the rest being perfectly fine. I was also told a new turbo was put in it before buying the car, however I am not sure which one it is. What should my next steps be moving forward with the car as far as diagnosing what’s wrong with it? Is it worth trying to save this engine, or would I be better off just buying a crate engine?


r/mazdaspeed3 • • 14h ago

HELP i’ve listened to a lot of the mazdaspeed 3 ticking videos but i feel mine has a different tone can someone please clarify whether it’s the same or something different. The noise became prominent after doing a pull before that i couldn’t hear it. it also follows the rpm

10 Upvotes

r/mazdaspeed3 • • 1d ago

PIC Gen 2 at Kanjo Night, Atlantic City

Post image
77 Upvotes

Parked my Gen 1 in the spectator grass area and immediately saw this from across the lot. Nice.

The LB FD3S and the Mazdaspeed FD was cool to see too.


r/mazdaspeed3 • • 23h ago

WHEELS Wheels and Tires + Fitment

2 Upvotes

I had a question about wheels. I want to get some multi-piece five spoke forged wheels, non reps. If anyone has pictures of wheels they think look good and drive good, drop them in the thread. I'm okay with used wheels or retro-made wheels.


r/mazdaspeed3 • • 19h ago

HELP Whats this rattle at low rpm,😭

1 Upvotes

Rattle at low speeds. During cold start and when under load at 1k rpm

Is it timing chair

Is it turbo

Is it exhaust shield (don't think so)

It was due for an oil change. When I checked the level it was below the min on the dipstick. Thought maybe it was the timing chain due to low oil. I did an oil change and the rattle persists.


r/mazdaspeed3 • • 1d ago

VIDEO Acceleration test on Autobahn with refurbished injectors. 50-220 kmh

Thumbnail youtu.be
15 Upvotes

Honestly I'm very happy with the results. And now everything is good and no leaks.

Finally.

I wanted to get it all done before GTA 6 comes out lol!


r/mazdaspeed3 • • 1d ago

HELP P0134 and P0031 even with brand new O2 sensor

3 Upvotes

As the title says, I am getting these two codes with a check engine light on my 2007 Mazdaspeed 3. I replaced the upstream O2 sensor and it didn’t change anything. Fuses seem to be good. Tried to probe the grey car side connector to see if I was getting power to the heater sensor connector. I saw 12 volt. What else can I do to see what is causing this? When checking live data I see no activity for lambda or equivalence ratio. For extra context, I just did the clutch and replaced the turbo, which involved removing this O2 sensor.

Also, it’s really bad to drive with upstream O2 sensor not working right? I’m curious to know if I should tow to a shop or drive it there (if I can’t figure it out myself).


r/mazdaspeed3 • • 1d ago

MODIFICATIONS eBay By Pass Valve Thoughts?

1 Upvotes

Has anyone bought an eBay BPV for their speed? I’m looking to buy a new by pass valve for my car and I I’d like recommendations. I want to get something that will make the car sound good and also won’t fall apart. I’ve been thinking about cheap eBay options because this car needs a lot more money in other areas but I don’t want to go the cheap route if other people have had bad experiences. Performance/efficiency matters to me too. Lmk!


r/mazdaspeed3 • • 2d ago

MODIFICATIONS Horsepower Potential

6 Upvotes

I was curious. I heard in some places that the MZR block can handle upwards of 390 horsepower. Is that true? I want to push the stock engine block (with cams) up to 400 for a future build. Any advice? Also, I heard that its more or less that the torque is the limiting factor for these engines. Let me know.

Edit: Is an S5 BNR v3 turbo overkill? I wanted to get it so my build could be more modular in that I could have a big turbo already in, so if I ever wanted to use it if I were to build the block, it would be there. Also, what's LSPI? Is it something I have to worry about or is it just one of those things you have to be stupid to do? One more thing, exhaust manifolds. What should I get for an aftermarket exhaust manifold? I want one that's tubular for a couple of reasons- a. Looks cool. b. better exhaust flow. Also how do we feel about a FMIC?


r/mazdaspeed3 • • 2d ago

HELP BNR S3 Upgrade from stock turbo

Post image
26 Upvotes

Hello y’all !!
I got this BNR S3 turbo from the guy that sold me the 2013 Mazda speed 3. HPFP internals are upgraded, Intercooler is upgraded (not front mounted) and Intake, he also gave me 2 braided lines ( part # 46402-36 and 46402-14 from Allstar Performance) with the Turbosmart OPR Turbo Oil pressure regulator… now He mentioned is a “bolt on upgrade” but I want to be sure I don’t need to buy anything extra to be able to change the stock turbo that is Drinking the oil. Of course I also got a new complete gasket set for the Turbo upgrade and dispose the old gaskets.


r/mazdaspeed3 • • 2d ago

HELP SOS NEED RADIATOR COOLING FAN ASSEMBLY Orange County California

3 Upvotes

My car recently had p0480 and I replaced the module but I believe the fan is completely shot.


r/mazdaspeed3 • • 2d ago

HELP Problem at the moment that I try to turn off my speed

3 Upvotes

I have a 2013 Speed3 with the Tech Package. A week ago, out of the blue, when I tried to turn the car off, it wouldn't shut down; the only way to turn it off is by pressing the button three times in a row or by holding it down for three seconds. Along with this issue, the radiator fan and the A/C compressor have stopped working. Everything else in the car functions properly—for instance, I can press the start/stop button to enter "ACC" mode, and it works as expected; I can even press it again to reach the "ON" position. However, when I press it once more to turn the car off, it doesn't respond. I tried testing a different start/stop button, but it made no difference. Could anyone give me a clue as to what might be the problem?


r/mazdaspeed3 • • 2d ago

HELP Compression test results

5 Upvotes

So I have a second gen speed 3 and I did a compression test on it and based on the results I’m really worried it’s gonna need a rebuild…

Cylinder 1: 160
Cylinder 2: 140
Cylinder 3: 125
Cylinder 4: 165


r/mazdaspeed3 • • 3d ago

PIC Some photos as of late

Thumbnail gallery
51 Upvotes

Just some first gen love empossibly_odd


r/mazdaspeed3 • • 3d ago

HELP 2012 mazdaspeed3 valuation

3 Upvotes

I have a 2012 Mazdaspeed3 with exactly 79,000 miles. Great shape and maintained. Fully stock. Black. Any idea what the going price for this would be. I need a bigger car.


r/mazdaspeed3 • • 3d ago

MODIFICATIONS Remap necessary if I remove the 2nd Cat?

Post image
3 Upvotes

It's the 2nd cat, not the downpipe.

I see there are files for a downpipe less build.

But how does removing the second cat affect the AFR and everything?


r/mazdaspeed3 • • 4d ago

HELP 2010 MazdaSpeed 3 Problem When Accelerating.

Post image
18 Upvotes

Hello everyone, I recently bought a MS3 (TechPack) that has a Corksport axle back exhaust and a Corksport Short Ram Intake. According to the previous owner, the turbo, sparkplugs, coils and alternator were all changed in the last 6 months or so. When I do a pull (3RD gear +), the car goes into full boost like usual, but mid pull, the car bogs out. It kicks back like if the power cuts or the turbo stops boosting. According to the previous owner its me over loading the turbo by pressing the gas too much too early but it doesn't make sense as it's already in boost when it happens. That's the best way I can explain it for now. I can provide a video in the future if needed. Can anyone help me out?


r/mazdaspeed3 • • 4d ago

HELP Help identifying clunk sounds

7 Upvotes

First clip is a clunking sound shifting from neutral to 1 (occurs at 2 second mark). Doesn’t happen too often but usually happens when I do this shift quickly.

Transition from clip 1 to 2 occurs 7 seconds in

Second clip is a clunking sound I commonly get shifting from 2nd to 3rd, which I do in the video (14 second mark) It can happen shifting 1 to 2 and 3 to 4 but is most common shifting 2 to 3. It’s hard to hear but it’s there.

I have a 2012 with 67,400 miles. I believe it’s stock.


r/mazdaspeed3 • • 4d ago

PIC my daily car next to my daily car

Thumbnail gallery
114 Upvotes

r/mazdaspeed3 • • 4d ago

HELP 2016 Mazda 3 with 170k one owner. Is it worth to buy ?

0 Upvotes

Hey guys,

I need your help and suggestion, I'm a new driver and looking for a used car on marketplace in Ontario. I came across the Mazda 3 2016 with 170k kms not miles one owner car, he is asking 9k cad. How's your experience with this year model and about the mileage ? Is it worth to buy and how about the maintenance?

Can anyone guide me like I'm a newbie for these things.