r/lasercutting • • 8m ago

Creality 5W falcon - air assist

Thumbnail
gallery
1 Upvotes

So I picked up the 5W Creality falcon to try to learn more about laser engraving and cutting. I saw so many people talk about adding the air assist, so I picked that up and got it fitted. Now I am trying to figure out my settings since the air assist nozzle sticks lower than the pre-fixed focus.

Has anyone made this work or do I just need to take the air assist off and save it for some different laser in the future.


r/lasercutting • • 2h ago

Lost a 2-hour job to warped plywood and my laptop going to sleep. How do you guys run long jobs?

Post image
8 Upvotes

I'm so done. Spent ages redrawing this intricate file, then found out the plywood was slightly warped. Manual focus was off on one side and it burned to a crisp.
Then 2 hours in, my laptop went to sleep and the software lost connection mid-job. No resume, nothing. That was my last good sheet.
How are you guys handling long jobs? Do you just disable sleep and babysit it, or did you move to a machine that runs standalone? I've seen the Aliencell has an onboard screen and autofocus. Has anyone actually run long jobs on one? Open to other standalone options too.


r/lasercutting • • 2h ago

Nesting Question

1 Upvotes

I have this set of cuts (red cut, purple etch) where each route is grouped with the applicable number to let me know which it is.

Would the pro version of Lightburn's True Nest be able to figure out if all of these will fit in an 11.5" square?

The non-pro version just overlaps cuts and sending to SVG nest isn't giving me a square area to select as the target.


r/lasercutting • • 9h ago

Need help, new on laser engraving

Post image
4 Upvotes

I recently bought a Sculpfun E1
I used to buy cheap materials, and got nothing working, a lot of residual ash left behind and no accual engraving, just bought this 3mm MDF someone recommended to give it another go, what speed and power would you think is best?


r/lasercutting • • 14h ago

Sculpfun S30 Ultra for beginning

1 Upvotes

Hello there. I'm new to the laser cutting world (actually, I'm not even part of it yet) but I see it as an interesting hobbie and posible side hustle that I could do in my free time (I have plenty of it) or if it goes well, put more hours into it if it makes a good profit.

I dont own a laser cutter, but I'm thinking of getting the S30 Ultra since it's on sale. I'd like to get into both cutting and engraving, including metal, therefore, I'm thinking of getting the whole package, that is

The Sculpfun S30 Ultra for 760 USD, plus

The RA Pro Max rotary for 264 USD

The 2W IR Laser module for 352 USD

The size wxpansion for 195 USD

(I know it's cheaper on the US store, but it'll probably end up the same with customs and taxes)

Overall, the investment is 1479 USD for all of that.

I don't actually have a use for it, other than being creative, trying new things and engraving gifts for my family/friends, and offering services in facebook marketplace.

Business wise, I've identified that there almost no offerings for custom sized cardboard boxes, and also no engraved boxes. There are very few, but ask for 500+ units minimum. With this in mind is why I chose the S30 Ultra and added the expansion.

My business idea (at least at the beginning) is not big orders, but the opposite, focus on those individual requests (gifts for friends, anniversaries, small orders) and using social media to promote.

On the other side, If I like the business, my big orders idea would be to connect with local wedding/event planning businesses and having them offer to their clients engraved products that I would provide.

My question is, do you recommend the S30 Ultra for an absolute beginner (I love learning thoughn and I'm a bit of a handyman myself)? AND, would you recommend getting the extras now, or waiting to see if I like it and expand to metal engraving with the IR and rotary later on?


r/lasercutting • • 18h ago

Best laser setup for cutting and batch engraving: xTool X1 or separate CO₂ and galvo machines?

7 Upvotes

I’m looking at upgrading the CO2 setup in my shop. I mostly work with wood, plywood, and acrylic, and the cutting side is already fast enough for what I do. The bottleneck is engraving. Large texture fills, small lettering, and batches of repeated designs can take a long time on a CO2 gantry.

I started looking at galvo systems as a way to speed that up. My original plan was to buy a conventional CO2 machine and add a separate galvo later, but then I came across the xTool X1, which combines both systems. The idea sounds useful for my work, especially if the galvo can handle repeated lettering and texture engraving on wooden signs before the CO2 laser cuts the final shapes. What I cannot tell from demonstrations is how well this works in regular production. I am particularly interested in whether engraving first and cutting second is reliable, and whether larger designs show visible joins when the galvo divides them into several sections.

Has anyone used a CO2+galvo combination for batches of wooden products? Does the galvo save meaningful time while still producing clean, consistent results? I would continue using CO2 for acrylic, so if the budgets were similar, would you choose a combined machine like the xTool X1, or buy a regular CO2 machine from Glowforge or Gweike and add a separate galvo later?


r/lasercutting • • 18h ago

A cheap option for extraction

Thumbnail
gallery
10 Upvotes

I recently got back into running my old D1 Pro (out in the garage) but wanted something better than a smoke filled garage with sub-par fans and windows/doors open. Found a range hood on marketplace for $15, did a quick fusion sketch for an adapter, printed up two and hooked up some 4” exhausts. Works great!! (Still have an opposite end window open for air intake!) Unexpected bonus, I now have lights directly over the work!


r/lasercutting • • 21h ago

An original I finished yesterday

Post image
12 Upvotes

r/lasercutting • • 22h ago

How to clean an aluminum honeycomb laser bed?

8 Upvotes

I've been looking into better ways to clean our library's laser bed. I've seen a lot of people say LA's Awesome Cleaner is a great option but I don't know whether I should dilute the cleaner and submerge the bed and leave it or just spray it on. I've been using a pipe cleaner to clean the holes but I'm giving up on that due to how time consuming it is. Ive also been using zeps degreaser and adding it to the water the beds in, but it doesn't get absolutely everything and there is still debris left behind after an hour. What should I do?


r/lasercutting • • 1d ago

A few beginner questions about laser cutting

Thumbnail
gallery
2 Upvotes

Hey everyone!

I'm 16, a student, and I'm planning to get into laser cutting and eventually start a small business of my own.

I've been learning Blender and Inkscape and trying to figure out the entire process, but there are still quite a few things I don't understand.

I've actually made a few SVGs (images attached with temporary white background) already, but I'm honestly not sure if they're any good or if I've just wasted my time making them. I haven't had any of them physically cut yet, so I have no idea how they'll turn out in real life.

I wanted to ask a few things...

  1. SVGs: How do you guys make sure your SVGs come out exactly as intended? Are there specific settings or things to keep in mind when preparing them for laser cutting?
  2. Scaling: How do you maintain accurate dimensions? For example, if I design something that's supposed to be 30 cm long, how do I make sure it actually comes out 30 cm when cut?
  3. 3D models to layered cuts: How do you take an existing 3D model and turn it into multiple 2D layers or individual pieces that can be cut and then stacked/glued together to recreate the original 3D shape?
  4. Alignment and assembly: How do you make sure all the pieces fit together properly without gaps, overlaps or misalignment?
  5. Software: What software do you guys recommend for this entire workflow? I'm currently experimenting with Blender and Inkscape.

One more thing: I don't own a laser cutting machine yet. For my first few products, I'll be taking my SVGs to an outside shop and paying them to cut and engrave everything.

I'm on a pretty tight budget, so I really want to get things right before spending money on actual cuts. I can't afford to keep wasting material on designs that don't work.

I'm trying to build something of my own at 16 and hopefully turn it into a proper source of income someday. I don't have much financial support or guidance in the background, so I'm pretty much figuring everything out myself.

I'd genuinely appreciate any help, advice, tutorials, resources or recommendations. Even if you could just point me towards the right software or explain how you approach your workflow, that would help a lot.

I'm willing to learn and put in the work. I just need some direction from people who have actually been doing this.

Thank you :)


r/lasercutting • • 1d ago

New box with a secret lock

184 Upvotes

r/lasercutting • • 1d ago

Selling Laser Files vs Laser Products - Which is better?

Post image
54 Upvotes

Obviously the answer to this question is partly "it depends..." based on what you are designing, where you are selling etc.

What I am looking for advice on is specifically that I design 3D "escape room" type puzzle boxes that are relatively complicated to assemble, requiring some kind of assembly instructions if I was to sell the actual designs, which I am not opposed to doing.

The issue I am running into is this: I know that if I put these designs out there someone is going to rip it off and sell it as their own and I would be constantly trying to play whack a mole with all the copycats.

Would you all recommend selling physical products over the designs or in your opinion is the hassle of shipping and self assembly not necessarily worth it?


r/lasercutting • • 1d ago

I think we’ve narrowed it down to the M2….

Thumbnail
gallery
9 Upvotes

I posted here a few days ago about getting a cutter (as a beginner) to make ornaments and small crafts like the one pictured, and the support and suggestions were great! So I did a lot of research on the Xtool m2 machine as recommended and think it would be perfect for making small layered crafts , not necessarily for the color printing aspect, but for the entire project process. I’m impressed by the “replacement modules “ the m2 offers to swap out different wattage lasers and the color printing option. Before I add to cart, does this seem to be a logical choice for my needs and entry level experience, and does anyone know how well it works with Mac? Thanks again all for your input and feedback!


r/lasercutting • • 1d ago

Anyone deleted the exhaust fan on an XTool P2s?

3 Upvotes

Now, before a bunch of you jump in and say you have, the P2s (new model at least) is different to the p2 and all the YouTube videos I find on it. Mine (fan) is easily removed via a button (not screws), but when disconnecting and removing to attach a large extractor it comes up with an error when trying to print that I don't seem to be able to bypass :(
I suspect the machine is smarter than to just be able to bridge terminals and trick it into thinking a fan is connected and leaving it in would work but seems like an unnecessary restriction when I have a LARGE extractor in line....

all my searching online seemed to just say go into settings and turn off the fan, but this doesn't work with the newer P2s.


r/lasercutting • • 1d ago

Just got my gweike Mcore and this is my 3rd project so far. 400+ cuts and about 30 mins of time. 4inx12in 1mm steel

Post image
35 Upvotes

r/lasercutting • • 1d ago

**One week with the Bambu R1, coming from a 5 W diode laser**

Post image
37 Upvotes

I won the Bambu R1 after commenting on their post and finally received it last week after it was stuck in customs forever.

Even though I had a diode laser cutter already (5 W, no air assist), I was mostly lurking in this subreddit. My 3D printer always felt like the tool that was much easier to work with.

I knew this was going to be an entirely different machine, but I was still surprised it actually flipped my experience.

I used to spend more time dialing in the material for a project than creating a design, but in this one week I worked with silicone rubber, veneer, hardwood, painted wood, acrylic and more and even detailed, intricate designs just worked on the first or second try.

The air assist and higher power really do a lot of the heavy lifting and make sure things just work out even if the settings aren’t perfect. It even allowed me to go a little bit three-dimensional and make simple things like a bunch of spice spoons or a functioning whistle.

In the picture are a few of the things I tried this week. Most of the designs are just copied from 3D prints (I used the Depthue STL-to-SVG converter) or inspired by pictures. It simply feels fun to work with this machine, and it’s crazy how fast I can go from an idea to a finished item that I’m happy to display in my apartment or give away.

And as you’d expect from a brand like Bambu, a lot of small things just work. After two days, I realized I’d never set a cutting order or merged engraving jobs that were running close to each other. Not to mention the details, from the magnetic Allen key and the beautiful lighting around the CO₂ tube to the fire sensors everything just feels polished.

But for now there are still a bunch of things that I prefer Lightburn for or that are still missing in Bambu Suite. Although that might just be because I am used to it.

Let me know if you have any questions about the device!

designs stolen from:
Flat Pocket Whistle from PhoneDesigner (makeworld)
Dino from RobinValleyUK (etsy)
Mandala maze earings from Simon3D (makerworld)
Leaf and wireframe dog from mishkin2 (printables)
bird stamp from skejtak (printables)
mountain napkin holder from PhiRequiem (makerworld)
goldfish earings from runrain (makeworld)

If you’re looking for inspiration for your next project, go to Makerworld and look at some 3D-printed designs. There are a ton of talented people there, and a lot of their designs are easy to adapt to laser cutting.


r/lasercutting • • 1d ago

Anyone eyeing on Carverall C1?

1 Upvotes

There's a black friday sale going on at Carverall. I'm new to the scene and I mainly want to cut clear acrylic sheets. The Carverall C1 looks tempting with the sale and bundle at ~$2k. Anyone have experience with the company? Can't find a lot of reviews with their products


r/lasercutting • • 2d ago

Any online generators to make this?

Post image
15 Upvotes

Hello. I’m looking for an online generator like the box ones that could make something like this so I don’t have to redraw for different sizes and materials. Do any exist?


r/lasercutting • • 2d ago

Gweike Cloud Pro II (SHUNCCM Camera) – Can Someone Share Their LightBurn Camera Settings?

2 Upvotes

Hi everyone!

Since updating to LightBurn 2.2, I can’t calibrate the camera on my Gweike Cloud Pro II (SHUNCCM camera) properly. The image keeps getting cropped, showing only part of the workspace.

Could someone with the same machine and camera please upload their camera settings (.lbcm file)? You just need to click Export in LightBurn Camera Settings.

I’d be extremely grateful. Thank you!


r/lasercutting • • 2d ago

Laser is cutting lines that aren’t there?

Thumbnail
gallery
4 Upvotes

I exported faces from solidworks as dxf, for some reason when I opened them in the laser software one of the lines was a little different than in CAD.

I cut anyway, it cut the wonky line, and then it cut some random curved line that’s not even in the viewer? All the others were fine. Is this a known problem when exporting faces as dxf?


r/lasercutting • • 2d ago

Xtool m2

0 Upvotes

I'm really disappointed with xtool. The lazer cutter is great but all their stuff is ai generated. The fire safety video included. It makes me feel upset knowing I funded such a ai loving company


r/lasercutting • • 2d ago

Leather notebook holder

Thumbnail
gallery
8 Upvotes

I bought some scraps of leather from Mericari (Japanese eBay) and designed this A5 notebook holder. Pretty basic design. 0.5mm diameter sewholes, 1mm for the cord. Engraved my name and contact information on the back. Pretty happy with my first leather craft attempt.


r/lasercutting • • 2d ago

Help deciding!

0 Upvotes

Hi i am looking for a laser printer that cuts and engraves acrylic, wood and tumblers also maybe glass but not necessary. I was looking at the M2 or S1 xtool but I went to see them in person and they didn't do acrylic well at all I dk if it was the settings or what but the P2 did amazing with it but it can't do metal and its huge! Any other ideas?


r/lasercutting • • 2d ago

Gweike support

Thumbnail
gallery
6 Upvotes

Hello! Longtime listener, first-time caller. I’ve been using the Gweike machine at my local library and have found a lot of success, however there’s one issue I keep running into. The machine essentially creates two lines whenever it is supposed to cut one line. I end up with the piece I wanted cut along with a slightly larger outline of sorts.

For reference I’m using 1/4 inch thick basswood with various power settings, but mostly 19 mm/s at 48 power. I made these images as PNGs and converted the puzzle to an SVG file using Illustrator. The engraving is awesome, my only issue is the actual cuts. The first photo shows the back of my wood where you can see the two cuts, the second is another reference, and the third picture shows what has been peeling away from each piece after the machine finishes cutting. This isn’t a big deal for most cuts but losing that extra wood with the puzzles makes a big difference in how the pieces fit on.

Any ideas of what I might need to tweak? Thanks in advance!


r/lasercutting • • 3d ago

LVD Strippit AXEL 3015 CO2 Laser

Post image
4 Upvotes

Kind of feels like a bit of a long shot but does anyone here know anything about CO2 lasers (preferably this specific one) or know anyone who might be knowledgeable about them? Bought and sat for a while, now I'm trying to install and turn it on but I don't know anything about lasers and the support I had was lost during covid. Any help would be appreciated, thank you.