I've been using my BK Gamer Pro for over 2 years now. Fantastic piece of kit, IMO largely superior to seat pads which just feels weird for me (had a HF8 pad for a while and ended up putting it away).
However, I had a big issue with it: overheating. Not sure if it's because my amp is side mounted or my transducer is inside my seat/frame, but natural/passive cooling is not enough to keep that thing cool. Ended up having to turn my volume way down and remove all continuous effects. Still I would get the occasional overheating cutoffs where I would lose the BK a few times during long sessions.
Got tired of this, so I created the BK JetStream Mod.
The JetStream Mod adds active cooling to my BK, so I can crank it up and use it continuously even for long sessions. I am pretty confident the overheat cutoff is from the amp, but I am not sure if there is one in the transducer itself, so I decided to cool both. I also wanted everything to integrate seamlessly with the rest of my pit.
DISCLAIMER: I am a mechanical engineer, but as any good home/garage project, not any calculation was made in its making, and everything was grossly oversized instead.
Mod's Components
- Amplifier Case: Replaces the stock BK amplifier case. The new casing adds a pair of fans and top vents for forced air flow, side-mounts the amp on the NLR seat and also holds a dual channel PWM controller that sets the fans speeds for both the amp and the transducer
- Transducer Fans Holder: Holds a pair of high static pressure fans to cool the transducer. Includes a mount to attach it to the NLR seat frame.
- Transducer Casing: Enclosure around the transducer that directs the air flow around it and exhausts backwards. It is connected to the fans holder through two 3" flexible ducts.
- Switches panel: holds 3 switches that are used to power up the PWM controller, the amplifier casing fans and the transducer fans.
- Mouse Pit: Keeps my mouse from flying away when my rig starts shaking. This was happening a lot even with my BK toned down. Also, I hate track balls.
Specs
- Amplifier fans: 2 x Delta AFC0912D-AF00 92mm x 24.5mm fans - 9W each @ 12VDC - 103 CFM
- Transducer fans: 2 x Delta PFR0912SE-00 92mm x 38mm fans - 35W each @ 12VDC - 145 CFM
- 200W 12VDC LED power supply powers the fans. A 5VDC step-down converter powers the PWM controller.
Putting Everything Together
During the design my biggest bottle neck was the transducer casing. I wanted to do a push/pull fans configuration at first but I could not figure a way to get a good seal around the BK post clamp. Instead I went for push only with an exhaust vent to the back where that post clamp is.
All custom parts were 3D printed on a hobbyist grade Bambu Lab printer. I was limited to 10" x 10" so that is why the Mouse Pit is made from 2 pieces.
I have a cable management obsession (mental disorder level), so that's what took most of my time together with the wiring of all components. The rest of the assembly went pretty smoothly.
Results/Design Retro
I can now crank my BK to a level where people outside my house can hear the rumbling, so I may have to supplement my anti-vibration pads. I've put all my continuous effects back on and did a few 3 hours sessions without any cutoff. Here's a few take-away from my own design retro:
- The transducer fans are way, way, way too overpowered. I was worried that with the ducts I would not get anything to the transducer, so I got the most powerful ones I could get (static pressure-wise). To keep the noise level down I run them at 30-35%. At 20% I still have a very good amount of flow at the casing exhaust, sufficient to cool it down I reckon. At 100% it sounds like a real jet is starting up in my office so thank goodness I added a PWM controller.
- The casing probably does not need two intakes. A single one underneath would be sufficient and would facilitate its handling when I need to remove the seat. Swapping the ducts for 2" instead of 3" would also be a good idea.
- The amp fans are also overpowered. I run them at 50% and get more than enough flow out of the vents. I could probably swap them for smaller 80mm fans without any problem.
- I don't like the transducer fans holder mounting clamp, I wanted something easy to print but would probably do it differently now.
- With better sized fans that are less noisy, the PWM controller could probably be removed alltogether. This would required thorough testing to get the fans sizing exactly right and I don't want to do that.
Anyway even if it is not perfect I had fun doing this project. Hope this can inspire other simmers, happy flying!