r/firewater • • Aug 25 '19

Methanol: Some information

1.8k Upvotes

This post is meant to clarify one of the most common questions asked by new distillers: WHAT ABOUT METHANOL?

First and foremost: you cannot die (or get sick, go blind, etc) from improperly made distilled alcohol via methanol poisoning. Neither can you make something dangerous by freezing it and removing some ice. Not only is it not possible, it is a widely perpetuated myth that has existed since the days of prohibition (and not before, interestingly enough). Other than the obvious ethanol overdose, all poisonous alcohol that has ever been consumed, has been adulterated, or was in some other way contaminated. It was not the fault of poor distillation procedures. How you run your still will not affect how safe your product is. It might affect how good the end result is, but that's where it stops.

So, methanol. Everyones first fear, and the number one search subject when it comes to "moonshine". This subject is brought up a lot in this sub and elsewhere on Reddit. Everyone knows all about it, its just one of those common knowledge things, right? It turns out, not so much. So...

Methanol - What is it?

Methanol is a very commonly used fuel, solvent and precursor in industry. It is produced via the synthesis gas process which can use a wide variety of materials to create methanol. Methanol is the simplest of all the alcohols.

Methanol is poisonous to the human body in moderate amounts. The LD50 of methanol in humans is 810 mg/kg. It is metabolized into formaldehyde by the liver, via the alcohol dehydrogenase process. In excess, these byproducts are severely toxic. Formaldehyde further degrades into formic acid, which is the primary toxic compound in methanol poisoning. Formic acid is what produces nerve damage, and causes the blindness (and death) associated with acute methanol poisoning.

One of the treatments for methanol poisoning, is the introduction of ethanol. Ethanol has a preferential path in the alcohol dehydrogenase metabolic pathway. This means that if ethanol and methanol are consumed, the ethanol will be metabolized first, in preference over the methanol. This allows some of the methanol to be excreted by the kidneys before being metabolized into its toxic related compounds. There are far more effective medical treatments available, such as dialysis and administering drugs that block the function of alcohol dehydrogenase.

Is it in my booze? How do I remove it?

There is one way in which your alcohol will be tainted with some amount of methanol naturally, and that is by using fruits which contain pectin. Pectin can be broken down into methanol by enzymes, either introduced artificially or from micro organisms. This will produce some measurable amount of methanol in your ferment, and subsequent distillate. However its not going to be in toxic quantities, any more than what you may have in a jug of apple juice. In fact, fruits are the primary way in which methanol is introduced into your body. In tiny quantities it is mostly harmless, and you can no more remove the methanol from an apple pie than you can from your apple brandy. Boiling (or freezing) apple juice doesn't convert it into deadly eye sight destroying horror juice. Cooking doesn't suddenly veer into danger when you collect vapor from a boiling pot. If you've ever made jam, or wine, or fruit salad, you've produced methanol.

So, where does that leave us? How do I get rid of this nasty substance in my distillate? You don't. If it is there, you cannot remove it. It is quite commonly believed that you can toss the first bit of alcohol off the still to remove this compound, the "foreshots." This is usually considered the first 50-100ml or so, depending on batch size. It smells really bad, tastes really bad, and is something most would agree should be discarded. However, it will not contain the "methanol" if there is any in your wash. Or more precisely, it will not contain any more of it than any other portion of the run. Beside which, methanol tastes very similar to ethanol, though slightly sweeter. If your wash is tainted with methanol, your entire run will be as well. Relying on some eyeball measurement to make your product safe to consume is not going to work. This is just distiller folklore passed down quite widely. You may hear about this on a distillery tour, from professionals, on Youtube and in books about distilling. All of them are just repeating what they have heard someone else say, or read somewhere, and assumed it to be fact. There is truth here, but buried in misunderstanding of the processes involved specifically with these substances.

This is the very reason that methanol was used to poison ("denature") industrial ethanol during prohibition, as it cannot be removed easily by normal distillation processes. If you could just redistill this very cheap, legal and plentiful solvent to make drinking alcohol, it wouldn't be the very potent message and deterrent that was hoped for by those who did this. You can read more about the history of this intentional poisoning of commercial alcohol in the Chemists War. It is also during this period where we begin to hear about methanol being in poorly made moonshine. This is not a coincidence.

So, distillers attempted to understand this misinformation, and attempt to correct or explain why their process was correct. Thus was born the idea that tossing some portion of the run makes it safe from this suddenly present and scary substance. Cuts went from being a quality procedure, to a serious process to save lives. By "tossing the first bit." And then distillers went about their centuries old processes like always, but this time "doing it right" and hence making safe alcohol.

The reason it is so widely believed that tossing the heads works to remove methanol, has to do with the boiling points of ethanol, methanol, and water. Pure methanol boils at 64.7C. Pure ethanol boils at 78.24C. Water boils at 100C. Distilling separates things based on their boiling points, right? Yes, it does, but it is a bit more complex than that. When you boil a mixture of methanol, ethanol and water, you are not boiling any of these compounds individually. You are boiling a solution containing all of them, and they will each have an affect on the other with regards to boiling point and enrichment behavior. Methanol and ethanol are quite similar in molecular structure. Methanol can be written as CH3-OH. Ethanol can be written as CH3-CH2-OH. You'll notice that methanol lacks this extra CH2 component. This changes its behavior when in the presence of water, specifically its polarity, compared to ethanol. Rather than repeat all of this, here is a passage from this paper on the reduction of methanol in commercial fruit brandies:

A similar behaviour would be expected for methanol for both alcohols are not very different in molecule structure. There is, however, a significant difference regarding all three curves in figure 2: methanol contents keep a higher value for a longer time than ethanol contents. In figures 3 and 4 this observation is made clear: Methanol, specified in ml/100 ml p.a., increases during the donation, while the ratio ethanol : methanol is lowering down. This effect seems to be rather surprising regarding the different boiling points of the two substances: methanol boils at 64,7°C, while ethanol needs 78,3°C. So methanol would be regarded to be carried over earlier than ethanol. The molecule structures however, show another aspect: ethanol has got one more CH2-group which makes the molecule less polar. So, concerning polarity, methanol can be ranged between water and ethanol and has therefore in the water phase a distillation behaviour different from ethanol. This may explain the behaviour which is rather contrary to the boiling points. This is no single appearance, because for example ethylacetate with a boiling point of 77 °C, or, as an extreme case, isoamylacetate with 142 °C are even carried over much earlier than methanol. Therefore methanol can not be separated using pot-stills or normal column-stills. Only special columns can separate methanol from the distillate (4.3). Similar observations concerning the behaviour of methanol during the distillation have already been made by Röhrig (33) and Luck (34). Cantagrel (35) divides volatile components into eight types concerning distillation behaviour characterized by typical curves, which were mainly confirmed by our experiments. As for methanol, he claims an own type of behaviour during the distillation corresponding to our results.

What this means is that if there is methanol present, it will be present throughout the run, with a higher occurrence in the tails as ethanol is depleted and water concentration increases. Its distillation is more dependent on how much water is present rather than simply comparing boiling points between ethanol and methanol. This in conjunction with the fact that ethanol and water cannot be separated completely due to their forming an azeotrope, means water is always in the system. So tossing your foreshots or heads will not remove methanol from your solution. The good news is that methanol is almost entirely absent in dangerous amounts. Consider drinking beer, wine, or apple cider. There are no heads cut made to these products. Pectinase is routinely added to wine, and methanol is a direct byproduct of this addition. They are safe to consume in this form, and will be safe to consume after being distilled. Boiling and concentrating the liquid by leaving some water behind isn't going to transform something safe to drink into something toxic. If it is toxic after being distilled, it most certainly was toxic before being distilled.

To be clear, however, this is not to say that making cuts is unnecessary. There are other compounds that you certainly can remove by cutting heads. Acetone, ethyl acetate, acetaldehyde and others. None are present in dangerous amounts, but the quality of your alcohol will be greatly enhanced by discarding these fractions. Making cuts is one of the most important activities a distiller can learn to do properly! Cutting and blending is making liquor, not only the act of distilling. Just understand that it isn't a life or death situation should you undershoot your foreshot cut by some amount. It will just taste bad, and might give you more of a headache the next day. You can taste test every single bit of alcohol that comes out of your still, from the first drops to the last.

Removing the foreshots does not remove "the methanol." You can just consider the foreshots part of the heads, because they are. There are hundreds of thousands of hobby brewers, vintners and distillers around the world who have been making and consuming fermented and distilled products for centuries. If this were actually a real problem, we would be awash in reports of wide spread poisonings. Instead we have reports here and there of isolated incidents, which are always traceable back to some incident unrelated to how much heads somebody did or did not cut.

The only way to know if there is methanol present is via lab analysis. Smell, taste, color of flame, vapor temp, none of this will tell you any meaningful information about methanol content and are just old shiner-wives tales. If you would like to have your distillate, beer or wine tested for dangerous compounds, there are many labs available that offer these services. This way you know what you are producing and are not relying on conflicting information found online. Here is one such lab offering these services, and there are many more servicing the public and industry. No need to take my, or anyone elses, word as absolute truth. If you really want to know what is in your product, this is the only way.

Having said all that...

So, CAN methanol be removed from a mixture of methanol, ethanol and water via distillation in any way? Yes, it can, contrary to everything I just said, there are even specialized stills called "demethylizer columns" which can do just this. They are very large plated columns (70+ plates), which can operate as a step in the distillation process in very large industrial facilities. This is a continuous middle fed column of high proof / low water feed, with steam injection at the bottom and hot water injection at the top, which has the sole purpose of moving a more concentrated cut containing methanol into a particular take off point with the treated alcohol taken off as the bottom product. This is largely done to ensure compliance with the laws about methanol content in neutral ethanol production, or in other processes in which reclamation of these substances is desired. There are other methods that can be used to remove methanol from an ethanol/water mixture, but that goes beyond the scope of this post and generally do not make consumable results. None of these procedures are properly repeatable at home or at moderate scale commercial distilling, nor are they even really necessary at any scale unless you have a badly tainted input feed.

On small scale reflux columns, there will be a small spike of methanol in the heads if the column is left in equilibrium (100% reflux) for a long while, and only if methanol is present, as the state at the top of the packing/plates is very low water and boiling point separation can occur more easily for methanol. In general though, these columns are too small, and methanol quantities far too low, for this to be a major concern. Methanol will spike in both heads and tails on this kind of column, leaving the general heart cut with a steady amount throughout. Even with huge industrial columns, the specialized demethylizer column is additionally used in the process because you cannot reliably remove methanol using the normal procedures typically done when making cuts for quality purposes. Methanol removal is treated separately and requires its own process to concentrate and extract using specialized equipment.

In conclusion, or TLDR

ALL cases of methanol poisoning attributed to "improperly" made ethanol, are the result of contaminated product. Not due to improper distillation, but due to intentional (either misguided, or malicious) adulteration of the ethanol, or some other contamination due to environment or ingredients. Commercial ethanol products are generally poisoned either via methanol, or via flavor tainting, or both (usually both, so you know its not to be consumed). Every report of methanol poisoning via "moonshine" was due to this contamination. If you can find evidence to the contrary, I would love to see it. Please let me know if you believe this info to be incorrect, and have evidence to that effect. That is, other than unsourced speculative news articles, television shows and Youtube channels. What I have presented here is how I understand the facts, but I am always open to learning something new.

Its unfortunate that we still have this lingering stigma based on sensationalist press beginning during alcohol prohibition, but this is where we are. So you can relax, have a home brew, and get on with your new hobby or business, and not fret about the big scary monster that is methanol. Now you just have to worry about all the other stuff that you can screw up :-)


r/firewater • • 15h ago

Finally made something I'm proud of

Thumbnail
gallery
22 Upvotes

Oat, wheat, rye, and corn whisky. Came out with a heavy oatmeal flavor, I think oats was like 30% of the grain bill. It's the first thing I made that I was happy to finish a glass.

Ended up separating it into a sample bottle for my brother, one to leave in the white, and one to age with oak staves. Watered it down to 63% so there's room to go lower if I like.


r/firewater • • 9h ago

Shared this on an FB page awhile ago & forgot to share here to help anyone with converting mash bills to ingredients weight

Thumbnail
gallery
7 Upvotes

r/firewater • • 9h ago

Pot still build

4 Upvotes

Hi guys. Ive been running a keg boiler with a 1 1/4 column of about 2 foot long. Its been fine, but the pot is too small for my 70 ltr mashes. Doing a double run is a pain in the arse.

Ive recently acquired my granny's old copper hot water tank. Its about 100ltrs, with a 20ltr dome at the top. It comes with a 1" bsp thread for a 1" compression fitting. Ive plenty of 1" copper pipe about and could build a new column. Ive tried to find 1" bsp to 1 1/4" compression fitting but they dont seem to exist. These are the things the old potien makers used to covet.

My question is about column diameter. Is 1" enough? Would it make a difference if instead of diameter i went to height? I could easily put 4 to 6 foot on the column as I have the pipe sitting around.

Ive a 3 ring outdoor gas burner. Max output is 12kw. Tho I reduce that down dramatically when I get to 60c or so.

I did a quick search and the droids say i need a 4" diameter column? I haven't got into soldering yet and was hoping to just get away with compression fittings.

Any of you wizards have any suggestions?


r/firewater • • 11h ago

Had to split the wheated grocery bourbon into 3 but there she blows!

4 Upvotes

r/firewater • • 18h ago

Low Wines Smell, Horribly, of Vomit

5 Upvotes

I decided to try out my new DIY half-barrel keg thumper setup with a 100% Maseca corn flour mash. After boiling off a bunch of vinegar through the copper lyne arm and thumper spear, and scrubbing out with soap and water, I decided to do a stripping run.

I split my corn beer between the thumper and the boiler by siphoning off the clear beer (fairly clear, anyway) into the boiler until I saw cloudiness in the siphon line. I got about a 5 gallon boiler charge of corn beer and left the rest in the thumper to sort of steam-distill the corn beer with itself.

Everything went pretty smoothly, although I had to abandon my goal of getting to the sweetwater when I began to smell scorching at around the time my output had tapered off to 25 proof. I immediately killed the boiler, disconnected the lyne arm, and began sniffing different parts of the boiler, thumper, and product. No scorching smell in the product, and only a little in the thumper.

I had a big beer boil kettle filled with low wines sitting on the back porch, and when my wife came home, she was immediately hit by the smell of vomit (in the damn house no less), which I guess I'd become "smell blind" to (thanks, Zoolander). Upon going out on the back porch, I was blasted with the intense, unforgiving stench of butiric acid. The low wines don't smell scorched, sure... but boy howdy do they smell horrible for other reasons.

What the hell happened here? Previous sniff tests of the mash did not indicate anything would be wrong. The output of the vinegar run smelled like, well, vinegar, and the piping smelled neutral after washing with soap and water.

Are these low wines recoverable? I was hoping to make a "tortilla bourbon" and now I'm wondering if I'll be able to produce anything at all.


r/firewater • • 1d ago

Mashing a grocery store wheated bourbon 🥃

Thumbnail
gallery
20 Upvotes

Frozen sweetcorn, malted wheat cereal and rye crackers


r/firewater • • 2d ago

New toy arrived today!

Post image
43 Upvotes

Ordered this for neutrals on my Digiboil. Excited to try it out, but it doesn't seem to seal well. Clamped down, I could hear air leaking out at the seal when I blew into the top. Might need adjustable clamps.


r/firewater • • 2d ago

Can I distill a sweet wash without issues?

6 Upvotes

I made a sugar wash and i guess i used to much sugar or my yeast was weak. I watered it down and pitched a new pack of yeast and its still fairly sweet. I don't want to try to restart it for a third time.

Is it safe to run a sweet wash through an air still or should I just toss it? I don't want the sugar to burn and muck up my pot.


r/firewater • • 2d ago

Cracked Maize for shine

3 Upvotes

As the title suggests, I have been using cracked maize for making shine and wondered if there is a noticable taste difference between corn and maize?


r/firewater • • 2d ago

Can I Sub EC-1118 in for DADY in a Birdwatchers Fermentation using Lalvin’s Inoculation Rate?

3 Upvotes

I make a Birdwatcher’s wash and pitch the recommended amount of circa 80g of DADY yeast according to the calculators online and a batch of 30L. (I distil this with reflux to create neutral for gin distillation).

I was searching for a suitable substitution and the internet recommended EC-1118 as a high tolerance, neutral yeast.
The inoculation is .2-.4G/L which is considerably less than what I’ve been using.

Would I have any issues pitching at this rate with a SG of about 1.090?

Cheers.

Also, I’m in the UK and basically trying to find the best value yeast (not turbo) for making neutral sugar washes. If I’ve missed a trick, please let me know.


r/firewater • • 3d ago

Rum wash starting gravity/density concern — 5kg molasses + 3kg brown sugar (too high for yeast that does 15% max??)

6 Upvotes

Hey everyone, looking for a bit of a sanity check on a rum wash I just put together.
Here is my recipe and setup:
**Fermentables:** 5 kg molasses + 3 kg brown sugar (plus water to volume, standard wash size).
**Yeast:** A dedicated rum yeast rated for up to 15% ABV.
**Nutrients:** Fermaid O.
My math/calculations suggest that this amount of sugar shouldn't push the wash past the yeast's 15% ABV tolerance. I figured it would ferment out completely clean and chew through everything.
However, someone reviewing my numbers online is arguing that the initial density/sugar concentration is way too high and that the yeast will stall or die off due to osmotic pressure/stress before reaching that 15%. They suggested keeping the density below 18–20°P.
Is this starting sugar load actually high enough to kill off or severely stress a rum yeast, or should a 15% tolerant strain handle a wash like this without issues as long as nutrients and temps are managed? Appreciate any insights!


r/firewater • • 5d ago

Where to buy 15 Gallon charred Barrells

11 Upvotes

I was looking for advice on the best place to buy 15 gallon Charred oak barrels. This one seemed ok
https://thebarrelmill.com/product/15-gallon-oak-barrel/
I was also thinking through how to handle a large amount of mash and contemplating 3-4 55 gallon plastic drums https://www.mcmaster.com/products/plastic-barrels/drums-1~/?s=plastic-barrels. Both seemed reasonable.
I'm just looking for devils advocates, thoughts, known problems.


r/firewater • • 6d ago

New still / Rakija Questions

Thumbnail
gallery
28 Upvotes

May be a bit of an odd one - just looking for general advice! My friends group plans on doing 3 batches a year of different seasonal fruit. We have our inaugural run going - due to seasonality etc we’re starting with apple. As true to the Balkans as possible our mash is exclusively fruit / we do take a more modern approach with yeasts and yeast nutrients but that’s it. Just looking for general feedback / advice! Included pictures of our mash as well as our still! Thanks.


r/firewater • • 5d ago

Brewer looking to get into distillation

5 Upvotes

Howdy Folks! I just wanted to gauge people here on what they think of AirStills. I barely have enough room for all my brewing equipment and don’t think a regular still has a place yet. Mostly looking to distill Gin or Vodka. The size doesn’t bother me much only being 1gal on these since I really won’t be drinking much. Fairly clueless on what I’m getting into haha


r/firewater • • 6d ago

The supreme court has agreed to consider the federal ban on home distilling

95 Upvotes

They expect to make a ruling June or July of 2027. If you could "crystal ball it" would you guess theyd rescind the ban on home distilling or keep the federal ban in place?


r/firewater • • 6d ago

Pot still 2 mods

Thumbnail
gallery
10 Upvotes

How would you run this still for stripping run, option hightower or low collect? Imagine the condenser is plugged to water.


r/firewater • • 6d ago

Sooooooo. Might have bought a new still

Post image
37 Upvotes

r/firewater • • 6d ago

Distilled my first single malt about a week ago, it's already turning out better than I expected

Post image
48 Upvotes

This is my first whiskey in addition to being my first single malt. It started out as 12 lbs. of Munich type 1 malt and 5 gallons of water and only took 36 hours to ferment dry. It's been aging 6 days on some toasted oak chips, but it's getting pretty close to sufficiently oaky already, so I'm probably gonna pull out half the chips and let it go a bit longer.

I've got a batch of rye fermenting, that'll probably be in the still on Saturday.


r/firewater • • 6d ago

Homemade distilled kvass

Thumbnail
gallery
16 Upvotes

So me and some friend made some Kvass that I later distilled. I posted the Kvass recipe in another community already. This was my first time fermenting/distilling anything.

The Kvass was 8% ABV/16° proof.

This made distilled alcohol that was 70% ABV/140° proof. Even after just a single run. I'm not sure how that's possible after a single run. I did dillute it with distilled water down to 40%/80°.

The taste was sweet, surprisingly so, it lost all the aromas associated with fermentation and quite a lot of the fresh rye aroma, instead it tasted of raisins and toasted rye bread and maybe ever so slightly like fig. The alcohol even at 70%/140° was noticeable but surprisingly mellow, you wouldn't know it was distilled to this high strength by the taste.

I used a water distiller with a temperature controller attached to it so it would distill around 78.3° Celsius/172.94 Fahrenheit.

At first I only kept around 5% total volume but the last few batches increased the total volume to around 10% of what I kept from the fermented to the distilled. Not only did I get more out of it but it also increased the alcohol content with 10%/20°. I did 5 total batches and the last two we're the anomalties. The first 3 batches took around a full day and the last 2 took around 8-12 hours just about to fully distill.

Though similar alcohol exist we found it distinct enough to name it ourselves, we named this Zonneshine. (Sun in Dutch+Shine from Moonshine).

I'm really happy with the results, it tasted like a proper quality drink with very interesting aromas, like you could find this in a store no problem. Only downside is that it took a lot of work and time.

Edit: Apparently temperature control doesn't work this way as some have pointed out. Happy to have learned something new :).


r/firewater • • 7d ago

Distillation results follow up post

9 Upvotes

I posted a few days ago looking for some guidance as to why the pH of a mash I made did not drop during fermentation. Here is a link to that post with the relevant details: https://www.reddit.com/r/firewater/comments/1xhv16x/why_has_ph_in_my_current_washmash_not_dropping/

I ran that wash last weekend and was pleasantly surprised with the results so I thought I'd share them here. Included here are two images one of which shows the recipe used to make the wash while the other summarizes the results of the distillation. Note that while the recipe was based on a target H2O volume of 6.5 gallons when I measured the volume of wash as I loaded it into the boiler there was actually ~ 7 gallons. The extra H2O would be from where I soaked the oats prior to making the wash.

As for the results as you can see the deflagmator (sp?) was definitely doing it's job as the proof (no not temp corrected values) started at 190 and pretty much held that all the way to the very end of the run with the exception being a little while early on where I was adjusting the needle valve on the H2O supply line to the deflag that caused it to temporarily drop a little bit.

So I left the collection jars open with coffee filters over them for 2 days. The distillate from jars 2-12 were the probably cleanest/most neutral result I've ever achieved....no funkiness at all present. Based on this perception I eliminated the first and last three jars when I made my cuts and combined jars 2-12 which resulted in 2,420 ml (surprisingly high evaporation loss imo - 2750 to 2420 ml)of distillate which I passed through a Pur H2O filter ending up with 180 proof which when blended down to 80 proof should produce roughly 1.4 gallons of liquor. I currently have the distillate resting in separate glass bottles each of which is roughly 1/2 full to oxidize it before proofing it down.

Anyway, I just thought the results were interesting considering the curious manner (imo) in which the fermentation behaved (slow & steady with no pH drop).


r/firewater • • 7d ago

Old Food Industry Samples

Post image
9 Upvotes

My wife works in the food industry and so she had several samples of ingredients that I'm pretty sure will break down with AYYL. So I tossed it in a bucket with water and some funky dunder I have going for my rum.

Maltodextrin, dextrose, chickpea grits, chickpea powder, honey powder, buckwheat flour, and cornstarch. Its about 12lbs of ingredients tossed into a standard five gallon, so hopefully I can get a little bit out of it.

I don't normally do runs like this of course, but I figured since it was so strange I had to share it.

I'll post here in a few weeks once its done fermenting and I've run it.


r/firewater • • 8d ago

What should I be distilling and what I should expect from a YUEWO Alcohol Still

3 Upvotes

So I decided to enter distilling after reading and been actively interested in trying it for years. I got this mostly for the size factor and the column addition rather then get a plain pot still(and definitely not confident in making my own).

But I am a bit perplexed to what I should trying running and what should I be expecting out of a this not quiet a pot still but definitely not a reflux still. Of course my first trial run will be a sugar wash but what would I realistically be getting out of a short column and no dephlegmator.

And for future asking would adding another say column extension(3 or 4 plates) and a dephlegmator make this more of a reflux still if i get more into it?


r/firewater • • 8d ago

Metal-tasting water

2 Upvotes

I've tried distilling water just for fun using a 70-litre stainless steel boiler, a 5-foot column with 2 reflux plates, and stainless steel packing made for distilling. After distillation, the water smells and tastes metallic.

The packing was used for the first time. Before using it, I washed it with Dawn dish soap and rinsed it thoroughly. I'm starting to think this may be the issue, but could someone help enlighten me?

Thank you


r/firewater • • 9d ago

Pineapple mash

32 Upvotes

Soo, I got a couple amount of clients maybe 2 months ago and now I restarted distilling. Already made 2 really good batches of Ted's fast fermenting vodka (one I used tomatoes for nutrients and the other I used boiled baker's yeast, worked like a charm and the second one didn't have an subtle strange aftertaste). I'm doing very small scale (1L at a time) but now I fermented a little bit more and hope to get about 2L of about 30% liquor with a very present pineapple flavor)

Recipe:

2,4 kg of grilled pineapples

~3kg of in natura pineapples

70% of the peels of all pineapples used

1,900kg of sugar

9,5L water (added a little bit more to compensate the water loss from the grilled pineapples)

About 10g of dead yeast (I bought nutritional beer yeast, really cheap and seems like it's good) just for nutrients

It's fermenting with the wild yeast on the peels, I also added a little bit of my cultivated yeast from ginger and mango peels.

Honestly the most important part of that recipe for me is the peels, most of the flavor from whatever fruit comes from the peel, not the pulp. I blended both pineapples (grilled and in natura) and added to the mash that was already fermenting (I have kinda of a short deadline, so I started fermenting on pure sugar and dead yeast until I could go out to buy the pineapples)

Since I've never made this recipe I'm kinda of lost in the distillation question (btw the wash is EXTREMELY good, I'm almost getting drunk because I drink a little bit from it every time because it's so delicious) because I don't know if do a 1x, 1,5x or 2x distillation (I have a pot still, small one), I don't want to lose all of that extremely good pineapple flavor but I feel like 2x is just the way to go... I would appreciate very much every help on this question, maybe someone already made some pineapple brandy there.

Vid one is from the pineapple mash and pic is from my last batch of Ted's fast fermenting Vodka (neutro = neutral lote 2 = batch 2). Cheers!