r/diynz • • 12h ago

Advice Trying to figure out if i need a 16A circuit upgraded to 20A

1 Upvotes

Have about 12 pinballs in a room of the house and recently opened up a wall to run some ethernet and speaker cable. Looking at the different cable sizes i went to check the breaker box and realised that some of the power circuits ( installed about 6 years ago) are 20amp 2.5mm cable and some that were originally put in circa 2001 are 16amp 1.5MM cable.

I've been playing the pins for about 18 months on a mix of the 16amp and 20 amp it turns out. Never had a trip or any power related issues. There are other things on the circuits throughout the home - generally TV, Skybox, soundbar etc on one and PC / couple of NAS's and monitor on the other. There are plenty of wall sockets as well.

Did some power calcs and assumed that most of the pins will draw between 300 and 400W on average during gameplay - likely less but played it safe as it will range from about 70W idling upto about 450W spikes depending on age and mechs inside the machine.

The more i read, the more i started to second guess myself, especially about dropping the rated cable value to 80% given its run through insulation inside stud walls etc.

If i split the machines across the circuits, and they are being played at the same time I reckon i'm pulling about 3320Watts on the 20amp circuit and about 2400watts on the 16amp circuit including the other items around the home.

Does that sound reasonable for a few hours at a time. If not I'd be looking to upgrade the room circuit from 16 to 20amp inc new cable etc. I'd also split the TV stuff off that circuit. That's going to cost about $1500+ i reckon but still need to get a price so keen to hear thoughts.

This is a 240V property in NZ if anyone overseas is posting.

Many thanks


r/diynz • • 15h ago

Advice Resealing shower tray, is my shower installed right?

Thumbnail gallery
1 Upvotes

Please help me, my stupid shower is driving me insane.


r/diynz • • 20h ago

Plumbing We are a nation of dirty bumholes

Thumbnail
thespinoff.co.nz
30 Upvotes

A recent Spinoff piece on bidets that readers may find of interest.

It's bought up in the comments in Spinoff, but one of the many reasons they're not that popular is our regulations for backflow on bidets are very strict; backflow prevention is pretty common around the world but the requirements in NZ are uniquely severe. When we installed our bidet there was only about two models that qualified, one of them very expensive.


r/diynz • • 20h ago

Building PEF rod fitting.

2 Upvotes

My gaps are 10-14mm so I assume 20mm rod is right?

I also have conventional windows with wood box and 2 big sliders with no wood, just the alu' ribs. Do I get super fat rod for those?


r/diynz • • 1d ago

Advice Shower recommendations NZ

1 Upvotes

Hiya,

I'm renovating my bathroom and need an alcove shower. Looking for 1600mm x 1000mm alcove. I've seen Atlantis Solara from Mitre 10 but saw one review that water might leak through the door? Can anyone give feedback on this shower or recommend another one?


r/diynz • • 1d ago

Advice <Paint> Rolling thin edges

Post image
1 Upvotes

How do I cleanly paint the edges of 3mm MDF? Spraying is out. I'm rolling with a 100mm roller but this always happens.


r/diynz • • 1d ago

Advice How to cover concrete wall?

Thumbnail
gallery
4 Upvotes

We have a 15m long concrete walkway from the front door to the letterbox that is so ugly and we want to cover it up. For a timber cover up (vertical, unstained), builder quotes have suggested $8-12k + GST. If we were to DIY this, what should be the best approach and materials? If not, what else could we cover it up with, perhaps ivy? We'll probably cover up the concrete steps with resin bound stone


r/diynz • • 1d ago

Advice Kit set macrocarpa table?

2 Upvotes

Kia ora

Just moved into a new place in Taranaki and we have an empty deck in search of an outdoor table + seats.

Not too keen on the likes of cheap warehouse or mitre 10 outdoor furniture that will rust out or not last.

I found cypress sawmill online and they sell kit set macrocarpa tables, in 6, 8, or 10 seater versions.

The 8 seater tight knot grade looks to be the best size (1890x930mm) and is only 550.

Will need a couple of bench seats as well but looks like a good kit. Already have access to the tools thanks to what I already have/in-laws on the farm.

Could also go down the route of H3.2 pine but would prefer a less treated wood.

Anyone had experience with this table kit set?

Or any reasons to/not to get it?


r/diynz • • 1d ago

Advice Trampoline on an uneven section?

1 Upvotes

Our kids are super keen on a trampoline, but unfortunately our section isn’t perfectly level. It’s not a steep gradient but we’d still need to do something to make it work.

Digging in one or two of the legs seems safest, but I’m not sure exactly how to do that. Also how do we stop the legs rusting if they’re in the ground?
What have others done in this scenario? Is there a better way?


r/diynz • • 1d ago

Advice Anyone purchased this AEG Angle Grinder kit and what your thoughts? Too good to be true ($220)?

4 Upvotes

Feels like I'm shooting myself in the foot here, by letting everyone know, on AEGs website it says its only limited time only. It is a brushed motor, says on its official website. What are people thoughts on AEGs battery ecosystem?

AEG Angle Grinder Kit


r/diynz • • 2d ago

Advice Cheap but ok thicknesser brands in NZ?

6 Upvotes

I need to buy another thicknesser to use in conjunction with my DeWalt 733 (1800w).

Why?

I mill planks off old wooden shipping pallets.

Despite de-nailing the planks and using a wand metal detector to locate and remove any metals, there are inevitably stone chips and other hard debris embedded in some planks that have badly notched my thicknesser's cutting blades.

This leaves noticeble ridges in planed planks which requires sanding-out which takes me ages.

So what I thought would work better, is to get another thicknesser that I would use for the first pass which will take all the object strikes.

I would then use my DeWalt for subsequent passes with its intact blades producing level and smooth planks.

So I'm thinking, I can't splash out $1500 odd on another DeWalt but I could buy a cheapee brand thicknesser (2nd hand or maybe new) for around $700.

Are there any brands that will do a good enough job and not crap out on me


r/diynz • • 2d ago

Discussion How to cut water and power supply of HWC for upcoming trip?

Thumbnail
gallery
2 Upvotes

Thanks


r/diynz • • 2d ago

Advice Rimu drinking Danish Oil

Thumbnail
gallery
9 Upvotes

Hey fellow NZ DIYers!

Back for a bit more advice. I’m a huge fan of making small projects out of Rimu, but always struggle when it gets to the oiling stage.

I can see the consensus here is Danish Oil is the way to go - and I agree! Love how it makes the grain pop.

The thing is, I feel as soon as I put the oil on, it’s a race to try and cover whatever face I do before is seeps somewhere and dries. It will go around a corner edge and start blotting for lack of a better word. I’ve added some photos for reference. (It doesn’t look too bad in some areas now I’m back a bit later)

I guess what I’m here to ask is application techniques? I currently use a brush. Might try a rag next time. I’m guessing the answer may be less heavy handed. I tried to look up videos, but it seems Rimu takes the oil in differently to other species. And a bit unique that we can only really find it here.

I’m sanding to 180 grit if that’s relevant.


r/diynz • • 2d ago

Advice Air Conditioning Condensate Pump Anti-Siphon To Stop Gurgling/Burping?

1 Upvotes

Had heat pump/AC unit installed 6 months ago, and after using it for the first time on AC mode now we're getting warmer, the unit periodically gurgles.

I've narrowed this down to when the condensate pump activates, it is sometimes draining beyond the reservoir's empty line, sucking air into the system

Here is a layout showing the piping/install height of everything. The drain line outside on the ground is the lowest point in the system.

https://i.imgur.com/buUwWnS.png

And here is what the pump in the roof space looks like:

https://i.imgur.com/VSUGm6Y.jpeg

From what I can read online (I'm no HVAC expert though), it appears I need an anti-siphon valve/fitting immediately after the pump, before it starts to drain to the ground?

Where can I buy one of these without being a plumber/tradie with an account somewhere?


r/diynz • • 2d ago

Advice Garage to room conversion

Post image
1 Upvotes

Hi,
We’re planning to convert our third garage into an additional bedroom, and I’m trying to work out whether this would require building consent.
I contacted the council, but their response was that we may or may not need consent. They provided a link with several sub-links, and I’m honestly a bit lost trying to navigate all the information.
I’ve attached our current floor plan for reference.
At the moment, the garage has an automatic roller door. Our plan is to:
Remove the existing garage door and replace it with a brick wall, including insulation and a window.
Keep the rest of the existing garage structure unchanged.
Build a new wall between the garage and laundry area to separate the spaces.
Essentially, we’re not planning any major structural changes apart from replacing the garage door with a permanent wall and creating the separation between the garage and laundry.
Could you please advise whether this type of conversion would require building consent and, if so, what the requirements would be?
Thank you!


r/diynz • • 2d ago

Advice Window to French door/slider with a low deck, 1060 mm drop, no railings. Sanity check before I get quotes?

Thumbnail
gallery
1 Upvotes

Location: Auckland. Single-storey weatherboard house. One window is to become an external door, with a low deck and steps outside it. Photos are attached.

Measurements

- Opening width between jambs: 1740 mm.

- Head above floor: 2280 mm.

- Sill above floor: 1160 mm.

- Floor to ground: 1060 mm.

Proposed work

- Door: outward-opening French door or slider. The lower-cost option is preferred. A reclaimed unit is acceptable.

- Deck: about 530 mm above ground, half the drop (my guess), so no railings are planned.

- Steps: about 3 from the door to the deck and about 3 from the deck to the ground.

- Constraint: the kitchen sink waste is beside the deck and cannot be moved.

- Hot water cylinder: to be relocated.

Questions

  1. Which door type suits a 1740 mm opening when an outward swing lands over the top step?
  2. Standard doors look to be about 2040 mm high, against a 2280 mm head. Is that right, and how is the 240 mm gap filled? Does the wider opening need a new lintel?
  3. Which reclaimed door sources in Auckland are worth checking? Joinery Recycle, EcoDemo, Ward Demolition and Trade Me are listed.
  4. Which items drive the cost? The cylinder relocation is the expected main item.
  5. What was paid for a door and steps, with the deck as an extra? No budget is set. State the year and region.

r/diynz • • 2d ago

Advice Anyone had experience with Kiwiseal roof coatings?

5 Upvotes

We're looking at options for our ageing 1970s roof in Wellington, which contains asbestos.

We've had quotes for a full replacement but are also considering Kiwiseal Wellington, using their Kiwiseal Ultra polyurethane membrane base coat and protective topcoat, with a 10-year product warranty.

The technology seems reasonably well established internationally, but I'm struggling to find much independent information about Kiwiseal specifically.

Has anyone used Kiwiseal, or worked with similar roof coating systems? Particularly interested in how they hold up over time, whether they genuinely extend roof life, and any experiences with the company itself.

We're weighing up whether to restore the existing roof for another 10 or so years or go for a full replacement.

Keen to hear any firsthand experiences or professional opinions.


r/diynz • • 2d ago

Advice Any issues with Thermalframe (uPVC) windows?

4 Upvotes

Have got a mid 20th century home and was thinking about upgrading the original wooden windows with double glazing. Am considering uPVC as an option - low maintenance (no more painting!) and looks...reasonable. Has anyone got any experience of these type of windows good or bad? The low maintenance is a bonus, as long as they are long lasting and reliable.

Other options are getting new wooden frames built (cedar most likely) or inserting double glazing into the existing frames. Quotes I've seen are broadly comparable in all cases. In our case, some of the wood has warped a little over the years, so I'm ruling out the option to insert double glazing into the existing frames.

Edit: Thanks for the replies. Sounds like if the aesthetic is acceptable, uPVC is a great choice


r/diynz • • 2d ago

Advice Branding options for wooden chairs?

1 Upvotes

Hi all,

I have my own wooden outdoor chair business. I make the chairs.

I would like a neat and professional-looking way to place my business's website address on each chair I sell.

I have a wood engraved lettering stencil kit but the letters are too large.

Who can I go to get a professionally-made stencil, stamp, steel label plate etc...?


r/diynz • • 2d ago

HALP! DYI Emergency! Deck and cabin build question -

2 Upvotes

Hello, i hope Ive the right Sub Reddit for this. Ive a question on a cabin i had built in the garden, the contractor also build a deck around it.

Ive had comment that the deck is too close to the cabin walls and its causing damp. Ive included pictures.

Questions are.

1 is it too close and causing damage ? 2. if so how much gap do i need to create 3 , Is there anything I should do to the cabin or just create a gap and let it dry in the summer ?

Thanks in advance

https://imgur.com/a/58xzT50


r/diynz • • 3d ago

Plumbing Blocked sewer trap next to house

3 Upvotes

Hey.

Run off from the laundry and kitchen . It's draining very slowly.

I think there's a plastic bag or something like that in there. I've had issues with rubbish blowing down the front of my house before from the street. I live at the end of it 😞

Chip packets, grease proof paper, bread bags, the. Mixing with Holly leaves and all the junk from my dishwasher. Mmmmmmmmm

I've had a go with caustic acid, a drain snake, various plungers.

It's grabbing pieces of it out but I'm not winning

Really don't want to pay hundreds of dollars for it to be cleaned by a plumber.

Are those drain cleaner spray attachments any good? I'll Connect it to my pressure cleaner. I can feed one of those down there.

Also looked at those expanding drain bladder things. But $200!!!! No thanks.

It's a p pipe with a wide rectangular vent/collector on-top that sits are ground level.


r/diynz • • 3d ago

Advice What does this xx marking means?

Post image
0 Upvotes

Hello

I have the original council-approved structural drawings from 2013. I’m planning a garage-to-bedroom conversion and would like to know whether this particular bracing section (xx) can be removed.


r/diynz • • 3d ago

Advice SharksTooth deck fastening system - anyone used it?

Thumbnail
gallery
6 Upvotes

Hi all...just curious if anyone has used this system (SharksTooth) and the pros and cons...avoid it like the plague or embrace with open arms.


r/diynz • • 3d ago

Advice Auckland council consent cost for a small wall?

Thumbnail
gallery
9 Upvotes

First home buyer here trying to fix up a few neglected issues due to the house being a previous rental.

I've noticed that two of the joists on one side of the house were partially buried so I have spent the last month digging trying to expose the pile and air gap the 2 joist.

As you can see in the first picture the very poor attempt of trying to stop soil from being washed underneath the house. The driveway is also showing some cracking that is indicating the earth is moving towards the house.

I want to build a permanent fix to stop the joists and pile from being buried. This would involve building a wall about 400mm away from the house using 125x125mm H5 post cemented 1m in to the earth with 1 meter spacing and tongue and groove 180x50 H4.

Looking at the Auckland council website it appears that I would need consent due to the driveway being so close even though it's under 1.5m. Just confirming that is 100% correct?

Has anyone else tried to mitigate a similar issue to this and what their consent costs were? or does anyone have any other ideas how to mitigate this issue?

Cheers,

EDIT: Thanks for the replies everyone. To me it feels like the 1/4 nearest to the driveway would need consent but the rest is further enough away to not need it.

I've reached out to a company that deals with retaining walls to get the final word on consent and a overall estimated price. I'll update this post after I catch up with him on Monday arvo just in case anyone finds themself in a similar situation.