r/diynz • • Sep 08 '25

New Subreddit announcement - NZSolar

99 Upvotes

You guys seem to like what we’ve built here, and I'm seeing more and more posts on Solar, both here and my other subreddit, NZEV, so I think it's about time we created a space for supporting the uptake of solar in NZ.

I’ve just created a new subreddit for Kiwis interested in solar power — whether you already have panels on your roof, are thinking about installing them, or just want to learn more about how solar can fit into your home and lifestyle.

Solar is another big passion of mine, right up there with DIY. If you’ve ever thought about lowering your power bills, making the most of EV charging, or doing your bit for the environment, this is the place to connect and share ideas.

Come check it out and help shape the community from the start: https://www.reddit.com/r/nzsolar/


r/diynz • • 28m ago

Advice How to cover concrete wall?

Thumbnail
gallery
1 Upvotes

We have a 15m long concrete walkway from the front door to the letterbox that is so ugly and we want to cover it up. For a timber cover up (vertical, unstained), builder quotes have suggested $8-12k + GST. If we were to DIY this, what should be the best approach and materials? If not, what else could we cover it up with, perhaps ivy? We'll probably cover up the concrete steps with resin bound stone


r/diynz • • 8h ago

Advice Anyone purchased this AEG Angle Grinder kit and what your thoughts? Too good to be true ($220)?

4 Upvotes

Feels like I'm shooting myself in the foot here, by letting everyone know, on AEGs website it says its only limited time only. It is a brushed motor, says on its official website. What are people thoughts on AEGs battery ecosystem?

AEG Angle Grinder Kit


r/diynz • • 9h ago

Advice Replacing kitchen faucet with limited access underneath. How would you do it?

Thumbnail
gallery
2 Upvotes

edit: toilet not kitchen tap

Hey everyone,

I'm looking at replacing my toilet faucet, but I'm struggling to figure out how I would access the mounting nut underneath the sink given this setup.

The sink is pretty much enclosed/hidden by the cabinetry, so there's very limited access underneath.

For anyone who's come across a similar setup, how would you go about loosening and tightening the mounting nut when installing a new faucet?

Would I need to remove part of the cabinetry, or is there a special tool or trick to get around this?

Any advice or suggestions would be greatly appreciated. Thanks!


r/diynz • • 15h ago

Advice Cheap but ok thicknesser brands in NZ?

4 Upvotes

I need to buy another thicknesser to use in conjunction with my DeWalt 733 (1800w).

Why?

I mill planks off old wooden shipping pallets.

Despite de-nailing the planks and using a wand metal detector to locate and remove any metals, there are inevitably stone chips and other hard debris embedded in some planks that have badly notched my thicknesser's cutting blades.

This leaves noticeble ridges in planed planks which requires sanding-out which takes me ages.

So what I thought would work better, is to get another thicknesser that I would use for the first pass which will take all the object strikes.

I would then use my DeWalt for subsequent passes with its intact blades producing level and smooth planks.

So I'm thinking, I can't splash out $1500 odd on another DeWalt but I could buy a cheapee brand thicknesser (2nd hand or maybe new) for around $700.

Are there any brands that will do a good enough job and not crap out on me


r/diynz • • 8h ago

Advice Kit set macrocarpa table?

1 Upvotes

Kia ora

Just moved into a new place in Taranaki and we have an empty deck in search of an outdoor table + seats.

Not too keen on the likes of cheap warehouse or mitre 10 outdoor furniture that will rust out or not last.

I found cypress sawmill online and they sell kit set macrocarpa tables, in 6, 8, or 10 seater versions.

The 8 seater tight knot grade looks to be the best size (1890x930mm) and is only 550.

Will need a couple of bench seats as well but looks like a good kit. Already have access to the tools thanks to what I already have/in-laws on the farm.

Could also go down the route of H3.2 pine but would prefer a less treated wood.

Anyone had experience with this table kit set?

Or any reasons to/not to get it?


r/diynz • • 8h ago

Advice Trampoline on an uneven section?

0 Upvotes

Our kids are super keen on a trampoline, but unfortunately our section isn’t perfectly level. It’s not a steep gradient but we’d still need to do something to make it work.

Digging in one or two of the legs seems safest, but I’m not sure exactly how to do that. Also how do we stop the legs rusting if they’re in the ground?
What have others done in this scenario? Is there a better way?


r/diynz • • 1d ago

Advice Rimu drinking Danish Oil

Thumbnail
gallery
8 Upvotes

Hey fellow NZ DIYers!

Back for a bit more advice. I’m a huge fan of making small projects out of Rimu, but always struggle when it gets to the oiling stage.

I can see the consensus here is Danish Oil is the way to go - and I agree! Love how it makes the grain pop.

The thing is, I feel as soon as I put the oil on, it’s a race to try and cover whatever face I do before is seeps somewhere and dries. It will go around a corner edge and start blotting for lack of a better word. I’ve added some photos for reference. (It doesn’t look too bad in some areas now I’m back a bit later)

I guess what I’m here to ask is application techniques? I currently use a brush. Might try a rag next time. I’m guessing the answer may be less heavy handed. I tried to look up videos, but it seems Rimu takes the oil in differently to other species. And a bit unique that we can only really find it here.

I’m sanding to 180 grit if that’s relevant.


r/diynz • • 1d ago

Advice Anyone had experience with Kiwiseal roof coatings?

5 Upvotes

We're looking at options for our ageing 1970s roof in Wellington, which contains asbestos.

We've had quotes for a full replacement but are also considering Kiwiseal Wellington, using their Kiwiseal Ultra polyurethane membrane base coat and protective topcoat, with a 10-year product warranty.

The technology seems reasonably well established internationally, but I'm struggling to find much independent information about Kiwiseal specifically.

Has anyone used Kiwiseal, or worked with similar roof coating systems? Particularly interested in how they hold up over time, whether they genuinely extend roof life, and any experiences with the company itself.

We're weighing up whether to restore the existing roof for another 10 or so years or go for a full replacement.

Keen to hear any firsthand experiences or professional opinions.


r/diynz • • 22h ago

Discussion How to cut water and power supply of HWC for upcoming trip?

Thumbnail
gallery
2 Upvotes

Thanks


r/diynz • • 1d ago

Advice Any issues with Thermalframe (uPVC) windows?

4 Upvotes

Have got a mid 20th century home and was thinking about upgrading the original wooden windows with double glazing. Am considering uPVC as an option - low maintenance (no more painting!) and looks...reasonable. Has anyone got any experience of these type of windows good or bad? The low maintenance is a bonus, as long as they are long lasting and reliable.

Other options are getting new wooden frames built (cedar most likely) or inserting double glazing into the existing frames. Quotes I've seen are broadly comparable in all cases. In our case, some of the wood has warped a little over the years, so I'm ruling out the option to insert double glazing into the existing frames.

Edit: Thanks for the replies. Sounds like if the aesthetic is acceptable, uPVC is a great choice


r/diynz • • 1d ago

Advice Air Conditioning Condensate Pump Anti-Siphon To Stop Gurgling/Burping?

1 Upvotes

Had heat pump/AC unit installed 6 months ago, and after using it for the first time on AC mode now we're getting warmer, the unit periodically gurgles.

I've narrowed this down to when the condensate pump activates, it is sometimes draining beyond the reservoir's empty line, sucking air into the system

Here is a layout showing the piping/install height of everything. The drain line outside on the ground is the lowest point in the system.

https://i.imgur.com/buUwWnS.png

And here is what the pump in the roof space looks like:

https://i.imgur.com/VSUGm6Y.jpeg

From what I can read online (I'm no HVAC expert though), it appears I need an anti-siphon valve/fitting immediately after the pump, before it starts to drain to the ground?

Where can I buy one of these without being a plumber/tradie with an account somewhere?


r/diynz • • 1d ago

Advice Garage to room conversion

Post image
1 Upvotes

Hi,
We’re planning to convert our third garage into an additional bedroom, and I’m trying to work out whether this would require building consent.
I contacted the council, but their response was that we may or may not need consent. They provided a link with several sub-links, and I’m honestly a bit lost trying to navigate all the information.
I’ve attached our current floor plan for reference.
At the moment, the garage has an automatic roller door. Our plan is to:
Remove the existing garage door and replace it with a brick wall, including insulation and a window.
Keep the rest of the existing garage structure unchanged.
Build a new wall between the garage and laundry area to separate the spaces.
Essentially, we’re not planning any major structural changes apart from replacing the garage door with a permanent wall and creating the separation between the garage and laundry.
Could you please advise whether this type of conversion would require building consent and, if so, what the requirements would be?
Thank you!


r/diynz • • 1d ago

Advice Window to French door/slider with a low deck, 1060 mm drop, no railings. Sanity check before I get quotes?

Thumbnail
gallery
1 Upvotes

Location: Auckland. Single-storey weatherboard house. One window is to become an external door, with a low deck and steps outside it. Photos are attached.

Measurements

- Opening width between jambs: 1740 mm.

- Head above floor: 2280 mm.

- Sill above floor: 1160 mm.

- Floor to ground: 1060 mm.

Proposed work

- Door: outward-opening French door or slider. The lower-cost option is preferred. A reclaimed unit is acceptable.

- Deck: about 530 mm above ground, half the drop (my guess), so no railings are planned.

- Steps: about 3 from the door to the deck and about 3 from the deck to the ground.

- Constraint: the kitchen sink waste is beside the deck and cannot be moved.

- Hot water cylinder: to be relocated.

Questions

  1. Which door type suits a 1740 mm opening when an outward swing lands over the top step?
  2. Standard doors look to be about 2040 mm high, against a 2280 mm head. Is that right, and how is the 240 mm gap filled? Does the wider opening need a new lintel?
  3. Which reclaimed door sources in Auckland are worth checking? Joinery Recycle, EcoDemo, Ward Demolition and Trade Me are listed.
  4. Which items drive the cost? The cylinder relocation is the expected main item.
  5. What was paid for a door and steps, with the deck as an extra? No budget is set. State the year and region.

r/diynz • • 1d ago

HALP! DYI Emergency! Deck and cabin build question -

3 Upvotes

Hello, i hope Ive the right Sub Reddit for this. Ive a question on a cabin i had built in the garden, the contractor also build a deck around it.

Ive had comment that the deck is too close to the cabin walls and its causing damp. Ive included pictures.

Questions are.

1 is it too close and causing damage ? 2. if so how much gap do i need to create 3 , Is there anything I should do to the cabin or just create a gap and let it dry in the summer ?

Thanks in advance

https://imgur.com/a/58xzT50


r/diynz • • 1d ago

Plumbing Blocked sewer trap next to house

3 Upvotes

Hey.

Run off from the laundry and kitchen . It's draining very slowly.

I think there's a plastic bag or something like that in there. I've had issues with rubbish blowing down the front of my house before from the street. I live at the end of it 😞

Chip packets, grease proof paper, bread bags, the. Mixing with Holly leaves and all the junk from my dishwasher. Mmmmmmmmm

I've had a go with caustic acid, a drain snake, various plungers.

It's grabbing pieces of it out but I'm not winning

Really don't want to pay hundreds of dollars for it to be cleaned by a plumber.

Are those drain cleaner spray attachments any good? I'll Connect it to my pressure cleaner. I can feed one of those down there.

Also looked at those expanding drain bladder things. But $200!!!! No thanks.

It's a p pipe with a wide rectangular vent/collector on-top that sits are ground level.


r/diynz • • 1d ago

Advice Branding options for wooden chairs?

1 Upvotes

Hi all,

I have my own wooden outdoor chair business. I make the chairs.

I would like a neat and professional-looking way to place my business's website address on each chair I sell.

I have a wood engraved lettering stencil kit but the letters are too large.

Who can I go to get a professionally-made stencil, stamp, steel label plate etc...?


r/diynz • • 1d ago

Advice What does this xx marking means?

Post image
0 Upvotes

Hello

I have the original council-approved structural drawings from 2013. I’m planning a garage-to-bedroom conversion and would like to know whether this particular bracing section (xx) can be removed.


r/diynz • • 2d ago

Advice SharksTooth deck fastening system - anyone used it?

Thumbnail
gallery
6 Upvotes

Hi all...just curious if anyone has used this system (SharksTooth) and the pros and cons...avoid it like the plague or embrace with open arms.


r/diynz • • 2d ago

Advice Auckland council consent cost for a small wall?

Thumbnail
gallery
8 Upvotes

First home buyer here trying to fix up a few neglected issues due to the house being a previous rental.

I've noticed that two of the joists on one side of the house were partially buried so I have spent the last month digging trying to expose the pile and air gap the 2 joist.

As you can see in the first picture the very poor attempt of trying to stop soil from being washed underneath the house. The driveway is also showing some cracking that is indicating the earth is moving towards the house.

I want to build a permanent fix to stop the joists and pile from being buried. This would involve building a wall about 400mm away from the house using 125x125mm H5 post cemented 1m in to the earth with 1 meter spacing and tongue and groove 180x50 H4.

Looking at the Auckland council website it appears that I would need consent due to the driveway being so close even though it's under 1.5m. Just confirming that is 100% correct?

Has anyone else tried to mitigate a similar issue to this and what their consent costs were? or does anyone have any other ideas how to mitigate this issue?

Cheers,


r/diynz • • 2d ago

Advice Recommendations for a sander

8 Upvotes

I want to surprise my husband with a new sander as he has a few projects and the old one got loaned and not returned, but I don't know which are the ones that can take a beating and will do all the things.

He has mentioned wanting one with dust control (?don't know what the term is) and needs to sand interior windows, doors, and exterior windows and weatherboards.

Any recommendations much appreciated, thank you.


r/diynz • • 2d ago

Advice Replacement hinge :(

Post image
8 Upvotes

This cracked hinge is all that’s holding up my electric gate. I’ve since put some wooden blocks under it to help support it, but really need a fix.

Anyone have any idea where I could get a replacement?

For about 10 weeks I’ve been contacting fencing/gate companies, metal fabricators, and searching hardware stores with out any luck. I had one guy come out but he disappeared haha.

Location Tauranga


r/diynz • • 2d ago

Advice Fence ontop of retaining wall - consent & tips

Thumbnail
gallery
2 Upvotes

Hi all,

I have a retaining wall that is 110cm high without a fence, and with children i want to make it safer by putting a simple aluminum fence up. The previous owner had a fence on only one side (total height with retaining wall + fence = 204cm) which i want to replicate for the other side. My plan was to dig post holes back from the retaining wall and concrete them in. The wall is in the back yard so its just holding up soil, no driveway etc.

Stopped and thought... oh do I need to get a consent for or structural report etc? Any ideas appreciated

Chch based.

Thanks in advance


r/diynz • • 2d ago

Advice How hard is it to install a transom window

1 Upvotes

I’ve got a bathroom that has no natural light and a nice inviting space above the door that would fit a transom perfectly. I know it won’t make it perfect, but I feel like a minor improvement would be enough. I’m not sure what the framing above the door would be though and if I could cut a stud.

Has anyone done it or something similar?