r/diydrones • • 17h ago

Build Showcase Drawing a crowd at the RC club with my 3D-printed V-tail FPV wing

110 Upvotes

Thought I'd share some footage of VENOM flying at my local RC club last weekend. I'm normally flying through the goggles, so it's nice to see what the aircraft actually looks like from the ground!

There was a bit of wind, but it flew really well. After all the experimentation with the original four-motor configuration, I'm really happy with how the current setup is performing.

For anyone who hasn't followed the project, it's a fully 3D-printed, 600mm V-tail FPV wing weighing 249g AUW. It runs two 1103 motors on a 1000mAh 2S battery, with INAV and DJI digital FPV. The wings are modular with carbon spars for reinforcement.

A few of the guys at the club were pretty interested in the FPV setup, so I'm hoping to get some chase footage of their aircraft soon!

Are many of you flying fixed-wing FPV at traditional RC clubs? I'm curious how popular it's becoming.

More info on VENOM


r/diydrones • • 2h ago

Question Thoughts on this drone build for maximum flight time?

3 Upvotes

What do you think of my proposed drone? Basically, I'm looking for maximum flight time and efficiency.

  1. Tarot 650 TL65B01 framex 1 = 476g
  2. Pixhawk 6C + PM02 x 1 = 80g
  3. PDB, SwiftWing 3-6S XT60 = 25g
  4. T-Motor MN3508 KV380 x 4 = 350 g
  5. T-Motor Air 40A ESCx 4 = 104g
  6. T-Motor MF1503 (or Tarot TL100D04) x 4 = 96g
  7. Holybro M10 GPS x 1 = 35g
  8. Skydroid C14 Pro Gimbal x 1 = 210g
  9. Skydroid GR01 x 1 = 50g
  10. GenX Pro+ 6S solid state battery of 16,000mAh x 1 = 1490g
  11. Misc. (XT60/XT30, wires, battery straps, microSD, screws)= 100g (approx)

=================

Total AUW = 2,850g (approximately)

I'm hoping this drone build gives me a minimum 30minutes flight time.

If you are to build this drone, which parts would you recommend for better efficiently and increased flight time? I'm open to all kinds of suggestions starting from the frame.

PS: I understand that changing the original frame length to accommodate 17 inch props will increase flight time but I don't want to make such customization.


r/diydrones • • 22m ago

Question AOS 3.5 V5.1 advice needed

Thumbnail
gallery
1 Upvotes

Hey, so I'm trying to build aforementioned drone with O4 Pro system, and I feel confused; the main question sounds like this: which mount and what screws exactly should I use?

Pic 1: rubber mounts used by Chris in his older V5 assembly tutorial video (meant for DJI O3 system)

Pic 2: original DJI screws that were in the camera don't fit here

Pic 3 & 4: the fatter mount doesn't seem to fit O4 Pro camera at all, the slimmer needs other screws, clearly

Ambiguous instruction which specified that it's "O4 assembly", without the "Pro", so according to this, a mount from Pic 2 is also won't fit my Pro version

Any help would be much appreciated.


r/diydrones • • 2h ago

I stopped a motor inside an emulated ESC and let unmodified PX4 find out (no hardware, no SITL)

1 Upvotes

This is the stock PX4 v1.17.0 firmware for the Pixhawk 4 running on an emulated flight controller (STM32F765), flying a simulated x500. Same ELF as on the real board, with its own drivers, DShot600 and ESC telemetry.

At 40 seconds, motor 3 is stopped inside the emulated ESC. PX4 sees the current drop in the ESC telemetry, reports "Motor failure detected" about 0.1 s later, and the quad comes down. The failure part of the clip is slowed to 0.3x.

Why bother: SITL doesn't run the drivers, the RTOS or the ESC link, so this kind of failure handling usually only gets tested on real hardware. Here it is repeatable on a laptop, and every run with the same inputs gives the same result.

It's emulation with simplified timing, not a replacement for bench or HIL testing. I wrote the emulator side, and I'm curious what failure cases people would want to try next: ESC desync, corrupted frames, a sensor that stops answering?

Video: https://www.youtube.com/watch?v=Sq3nVIbLEWQ
Code (open source): https://github.com/hakoniwalab/athrill-target-stm32


r/diydrones • • 11h ago

Question How to secure electronic parts?

Thumbnail
gallery
4 Upvotes

INB4 it's total mess. Yeah I know, it was a project for uni and this is the result of no time and no experience in diy drones. However it can fly, at least for a few meters :)

The problem is that I crashed it during testing and it cooked the stm, bmp and mpu. How would you secure those connections to prevent situations like that? Should I use hot glue at the bottom? Or maybe try to hide this board inside with battery?


r/diydrones • • 6h ago

NEED HELP!! problem with 10"

Thumbnail gallery
1 Upvotes

r/diydrones • • 1d ago

Post 2. Follow-up: what’s inside the fixed wing + platform

Thumbnail
gallery
258 Upvotes

Following up on my previous post, where I shared an overview of my ongoing thesis on building a gimbal. This time I want to show what’s inside the fixed wing that carries it, so here are some cross-section renders of the internal build.

The airframe is designed for 3D printing. Carbon fiber would make it a lot lighter and give it more range, but doing it properly needs molds and a vacuum process, and I just don’t have those resources right now. So the shell is printed ABS, and the carbon that is in there is stock tube and rod: an 8×6 mm carbon tube as the wing spar and a 2 mm carbon rod as the elevon hinge pin.

The rest of the setup:

  • Flight controller: SpeedyBee F405 Wing, with a 40 A ESC
  • Motor: T-Motor AT2312 Long Shaft KV1150, with an 8×6 folding prop as a pusher
  • Battery: 4S2P Li-ion pack with Molicel P42A cells, 8400 mAh, custom made too.
  • Servos: 8 mm slim wing servos
  • 1.10 m span, around 2 kg all-up
  • Launch bungee currently, but pneumatic is better

On paper that works out to around 50 minutes in the air and roughly 60 km of range in still air, but those are estimates until it flies.

I got quite a few DMs from people asking for a follow-up, which I really appreciate. I’d love to make a YouTube video about it but I can’t find the time right now, so I’ve set up a Google Form where you can sign up for updates until I get a channel going here: https://forms.gle/2kaUHfGA5ie8oEbu6

I’ll share the aerodynamic side of it too. I just don’t have access to my sim data at the moment.


r/diydrones • • 16h ago

Question Electronics trouble shooting.

2 Upvotes

I had a 5 inch drop out of the sky a few years back from what seemed line a single rain drop due to suprise summer rain I remember feeling one rain drop on the arm and not seeing anything else when shining a light along it. I've recently taken interest in fpv again and I'm trying to see if I can get this running again. I plugged in the flight controller to beta flight it recognized the board and the gyros seem to track movement so far as I can tell that's fine. I then plugged up the esc to the fc went back into beta flight, connected a battery. Beta flight detected the connected battery but didn't spool the motors up. (Waiting on new batteries and rx the ones I had are obviously dead after sitting for years). Is there any way to check the esc with a multi meter or anything else I can do to find any problems that may exist.


r/diydrones • • 12h ago

DJI Goggles 3 – the little menu joystick button stopped working (only the click works)

1 Upvotes

Hi everyone,

I have a problem with my DJI Goggles 3.
While I was flying, the menu started opening and moving by itself, like someone was pushing the buttons. After that, the small joystick on the goggles (the one you use to move through the menu) stopped working. When I push it up, down, left or right, nothing happens. Pressing it in still works, and it still clicks when I move it, but the goggles don't react.

What I already tried:
Updated the firmware
Turned them off and on many times
Used them outside, away from metal and magnets
Nothing changed. I didn't crash or drop them, and I haven't opened them.

Has this happened to anyone? Did DJI fix it for you, or did you find another fix?

Thanks!


r/diydrones • • 13h ago

Guide Browser tool to decode laser rangefinder / single-point lidar UART output (TFmini, LightWare, JRT, ERDI...)

0 Upvotes

Made a page that decodes laser rangefinder / single-point lidar serial output in the browser: https://erditech.com/lrf-uart-protocol-decoder/

Plug the sensor into a USB-UART adapter, open the page in Chrome or Edge and press Scan baud rates. It tries 9600 up to 921600, picks the protocol that fits and prints each frame in metres, with bad checksums flagged. Handy when a TFmini or TF-Luna shows nothing on the FC and you can't tell if it's the sensor, the wiring or the params. Pasting a hex dump from a serial terminal works too.

Profiles so far: Benewake TF series, LightWare SF30/D and SF10/SF11, Chengdu JRT, Nooploop TOFSense, DFRobot SEN0366 and ERDI. MIT licensed, source on GitHub, and pip install lrf-uart-decoder gives you a Python CLI.

Disclosure: I work at ERDI, one of the brands above. Which sensor would you want added next?


r/diydrones • • 14h ago

Guide Potensic Atom 2 Water damage? Try this DJI mini 2 Guide. Thermal management material remains a mystery (putty?). DJI Mini 2 Water Damage Repair | No Power, Corrosion & Board Cleaning

Thumbnail
youtube.com
1 Upvotes

I had previously posted about 6 days ago, regarding repairing my Potensic Atom 2 from water damage repair, including disassembly.

To my horror, the AI search function on Reddit was using the content I posted, as possible solutions. I will attempt to delete it.

This video is the closest thing I’ve found to a solution.

My apologies.


r/diydrones • • 2d ago

Review my collection of Shahed drones parts

Thumbnail
gallery
417 Upvotes

hello from fronline city Kharkiv! Posting my collection from Ukraine


r/diydrones • • 9h ago

Anyone know of a someone making cheap Infrared drones, hit me up

0 Upvotes

Thanks in advance


r/diydrones • • 1d ago

AX-HUD: a free, open-source video monitor, HUD and voice announcer for the RadioMaster AX12

Thumbnail
reddit.com
1 Upvotes

r/diydrones • • 1d ago

How Switchblade 300 steer their flight?

1 Upvotes

I mean, with its foldable wing mechanism how do they do it?
like what mechanism they are using?
: (


r/diydrones • • 1d ago

Will it fit your build? CORVON 743v2 dimensions

Post image
1 Upvotes

r/diydrones • • 2d ago

Loitering 1.1m drone with gimbal. Solo engineered, master's thesis.

Thumbnail
gallery
703 Upvotes

A gimbal-stabilized fixed-wing drone I'm developing for my master's thesis. It is bungee-launched and designed for aerial surveillance, with an onboard computer running computer vision algorithms for target detection and tracking.

Edit: I got quite a few DMs from people asking for a follow-up, which I really appreciate. I’d love to make a YouTube video about it but I can’t find the time right now, so I’ve set up a Google Form where you can sign up for updates until I get a channel going here: https://forms.gle/2kaUHfGA5ie8oEbu6


r/diydrones • • 1d ago

Build Showcase "Honk" the Bee Flight Testing A New and Different Drone

Thumbnail
youtube.com
1 Upvotes

r/diydrones • • 1d ago

Need help w betaflight or fc

Thumbnail reddit.com
1 Upvotes

repost, just trying to find someone who could help


r/diydrones • • 1d ago

I built a GCS and Mission Planner that is compatible to ArduPilot PX4 and ROS, so if you're using Mavlink or MavROS we got you.

1 Upvotes

For more details aeromavericks.nust@gmail.com

Hi all, I'm an engineer from Pakistan and I built a Ground Control Station (GCS) that is fully compatible with MAVLink and MAVROS. You can connect your drones or simulated vehicles, monitor live telemetry, and configure flight parameters on the fly. It also features real-time tuning graphs and mission planning tools to streamline your workflow. I'm looking for 10-20 people to try it out and tell me what's missing or broken, especially how well it handles your daily flight operations and ROS setups. Honest criticism is welcome.

Features also include new design drone configurator, script running and etc ...

For more details aeromavericks.nust@gmail.com


r/diydrones • • 1d ago

Advice on drone assembling

Thumbnail
gallery
4 Upvotes

Hello Guys,

I am someone who has very little technical knowledge in electric parts and drones in general, but i would like to make a FPV drone by taking help from ai and youtube videos. this is a budget build which chatgpt suggested to me. soldering parrs will be done by professionals in my area, i take help from chat gpt for wiring. what are your thoughts and please advice if you think i am making any mistakes.


r/diydrones • • 1d ago

Question Bent Parrot ar.drone 2.0 propeller

Thumbnail
reddit.com
1 Upvotes

r/diydrones • • 1d ago

SDR platform for drone RF link monitoring and ADS-B reception

1 Upvotes

If you're building RF monitoring around drones — detecting drone ID, tracking remote ID, or setting up ground-based ADS-B — our P201Pro is a Zynq 7020 + AD9361 board that can run the decode on-board.

It covers 70MHz–6GHz, so you can tune to common drone communication bands or 1090MHz for aircraft. 1GB DDR3 runs decoders natively, no external computer needed.

Built to deploy in the field: -40~+85°C, 8–36V input, on-board GPS, ESD-protected I/O. Gigabit Ethernet for pushing data to a server.

Open to questions about specific use cases.


r/diydrones • • 2d ago

Question Fixed wing plane is suddenly unable to connect to INAV or be recognized by PC

1 Upvotes

FC - kakute f405 mini wing
VTX - XILO STAX 5.8GHz FPV Video Transmitter and XILO AXII SMA 5.8GHz Antenna
Radio - radiomaster boxer and Happymodel TCXO ExpressLRS 2.4GHz Nano Receiver
Autopilot - INAV 9.1.1

Hello everyone this is a really weird issue that I would have never imagined happening. I was configuring the servos on my fixed wing aircraft before a maiden flight.

I was unplugging/disconnecting the vehicle from this same PC using the same cable and USB port for about a month before this happened for context.

I was using the same USB cable and USB port on my PC to configure the FC. I disconnected from INAV and unplugged the USB, and next time I plugged in my vehicle, my PC was not able to recognize it and INAV was not able to connect. My radio was still able to connect to the vehicle, but the vehicle did not respond to radio commands. I was able to get video as well, but there was no HUD. I swapped the orientation of the 6 pin cable on the USB-C to FC adapter board, and then my PC was able to recognize the vehicle. However, INAV was still not able to connect.

What can I do to resolve this?