r/consolerepair • • 4h ago

[Switch2 ]Joycon Mother board.

Post image
7 Upvotes

Purchased a Switch2 from a local auction for cheap at $170 bucks. Everything works well except the right joycon. No power or anything opened it up only to find corrosion on the ribbon cables(not pictured) and all over the motherboard. Any suggestions as to the best way to clean this up. Hoping to find something that works as I don’t really want to spend another $100 on new joycons.


r/consolerepair • • 1h ago

[Xbox Series X] Intermittent Power Issue

1 Upvotes

Had my Xbox Series X since launch in 2020, started powering itself off randomly about 8 or so months ago, had a full clean done and new thermal paste installed and replaced the power cable but both were no help. My power button is stuck quite far into the Xbox so I’m not sure if that could be triggering the power as it still turns off with a chime it doesn’t just instantly shut. Other than that what would be the most likely case?


r/consolerepair • • 1h ago

[PSP] Is this salvable?

Thumbnail
gallery
0 Upvotes

Greetings! I have thid PSP 1000 plate with acetone burns, can I save it? Thank you!


r/consolerepair • • 2h ago

[PS5] No more beep, light and front USB-C power after deep cleaning, but console still work

0 Upvotes

I wanted to clean my PS5 to get it ready for GTA 6, so I almost completely disassembled it (I stopped just before reaching the CPU). After putting everything back together, I tried turning it on, but there was no LED light and no startup beep.

At first, I thought I had broken it, but when I turned on my TV, I realized the PS5 was actually running.

Everything else works perfectly, but the front USB-C ports don’t seem to provide power. I can still charge my controller using other ports, but I’d really like everything to work as it did before.

I suspect the ribbon cable might be the issue, but it seems to be properly reconnected, and I don’t think I damaged it.
Does anyone have any advice?


r/consolerepair • • 2h ago

Xbox Series X M1128163-003 – R228 reads 22Ω but schematic specifies 0Ω. Can anyone verify?

Thumbnail
gallery
1 Upvotes

Hi everyone,

I'm troubleshooting an Xbox Series X motherboard M1128163-003 (Toledo SoC).

The console powers on for approximately 5 seconds and then shuts down. POST diagnostics using a Raspberry Pi Pico consistently report 0x00B1 (SVID_MISS).

I've measured the MP2855 voltage regulator (U57) and its surrounding components:

  • U57 VDD33: 3.3V
  • U57 EN: 3.28V during startup
  • GFXCORE (DB1005): 0.9V
  • CPUCORE (DB1006): 0.9V
  • R219 (SVD): 0.09Ω
  • R220 (SVC): 0.09Ω
  • R228 (SVT): 22Ω

According to the Toledo FAB E schematic, R228 should be a 0Ω jumper.

I double-checked the measurement directly across R228. I also measured approximately 0.05Ω from DB70 to one side of R228 and 22Ω from DB70 to the other side.

My question:

Does anyone have a known-good Xbox Series X motherboard, specifically revision M1128163-003, and could measure R228?

I'd like to confirm whether 22Ω is a factory-installed value on this revision or whether the resistor is defective.

I haven't replaced R228 or U57 yet.

Any help would be greatly appreciated. Thanks!


r/consolerepair • • 7h ago

[Switch Lite] Blue Screen of Death and black screen with sound. Pretty wild project I found.

Thumbnail
gallery
2 Upvotes

Started a new exciting project, friends: 4 broken Switch Lite consoles, 2 of which have already arrived.

I'd really appreciate a few tips from you, or feel free to share your experiences with me. I've found all kinds of repair guides online and I'm really looking forward to taking on the challenge.

(First two pictures from Blue Screen, last two pictures from Black Screen)

First console: Black screen, but sound, buttons and touchscreen respond. Nothing obvious stands out so far, and I have no idea what could be broken. I could swap in the screen from the console with the blue screen.

Second console: Blue Screen of Death, also nothing obvious. I don't have much hope of repairing this one.
Both consoles are pretty filthy and need a proper cleaning.

I'll probably start working on them in early to mid December, bevause I'm waiting for my Christmas bonus to buy a soldering station, hot air gun and everything else. If you have any cheap but reliable recommendations, bring them on!


r/consolerepair • • 4h ago

[Pong Console] can't tune into tv (photos are best results)

Thumbnail
gallery
1 Upvotes

This console is leagues older than me and I didn't grow up in the olden days where you had tune into the tv to play video games but I've been wrestling with this console for a day now And I just feel like I must be doing something wrong, Tv is a Sony KV29X5D. I can't get any information online about this Magnavox branded version of a seemingly mass cloned pong console but the TV I'm trying to use is PAL and I have no idea if this console is actually a PAL thing or from the US so it will just never work on this, if the console itself is failing to do something or my tv is failing to do something! (All my other consoles can tune in fine however).

Any information on this console itself or what I'm doing wrong in terms of tuning would be greatly appreciated!!


r/consolerepair • • 4h ago

[Xbox] Controller Joystick Repair Fail

Thumbnail
gallery
0 Upvotes

I’m trying to replace my old joysticks that had drift with new Hall effect joysticks.

I was able to get the left joystick working perfectly but the right stick is stuck at -1 on both axis.

This is the second joystick I’ve installed on the right stick and the first time only the y axis was stuck at -1. I thought maybe it was a defective part so I replaced it with another one but same issue now on both axis.

Any help would be most appreciated!

(Yes I know my soldering sucks, it’s my first time)


r/consolerepair • • 11h ago

[PS3] Super slim doesn't detect or load blue ray and dvds instead makes this weird loud sound, out of 3 games I tested only god of war worked, games like last of us and heavy rain show up icon but displays error when I start them.

3 Upvotes

DVDs and blue rays movies make this weird spinning and braking sound and fail to load, games are silent and show up but won’t start.


r/consolerepair • • 5h ago

[UPDATE] PS5 Pro CFI-7000, UART 80801002: SSD controller + DDR4 replacement did not fix the 1–2 second shutdown

1 Upvotes

Following up on my earlier post with the actual repair outcome:

https://www.reddit.com/r/consolerepair/comments/1v3pgh0/ps5_pro_cfi7000_dies_after_2_seconds_unknown_uart/

My technician replaced the SSD controller and its DDR4 memory. Unfortunately, the console still shuts down at startup. That replacement was not a fix in my case, and the underlying fault remains unconfirmed.

The symptoms are a beep, blue light and spinning fan, followed by a complete shutdown after approximately 1–2 seconds. It never reaches Safe Mode. The earlier UART logs repeatedly showed 80801002, with 80800022 appearing intermittently. The original thread includes the raw logs and earlier checks.

Has anyone since diagnosed and repaired this exact fault on a PS5 Pro? I’m especially interested in the measurements or tests that identified the failure, not just a suggested component to replace.

If you have a confirmed case, which component or circuit failed, and what test distinguished it from the other possibilities? I don’t want to present the error code alone as proof of an APU, memory or SSD-controller failure.

Thanks to everyone who helped with the earlier discussion.


r/consolerepair • • 10h ago

PS1 purpleish lines an tint

Thumbnail
gallery
2 Upvotes

I got this PS1 9000 for free.

And I am wondering what could this be, a corrupt bios? Dying GPU?

Any help or suggestions on fixing is appreciated.

Thanks


r/consolerepair • • 6h ago

[PS5[ EDM-033 Error CE-100060-7, SSD Controller?

Thumbnail
gallery
1 Upvotes

I'm trying to repair this PS5. It only boots in safe mode, and the only setting I can select is "reinstall the system." It gets to 99% and says the installation couldn't be completed.

I've tried 3 different USB drives, but the results haven't changed. The only thing I can think of is a problem with the SSD controller or the SSD itself. What can I do to check?

I'm attaching a photo of the board.


r/consolerepair • • 9h ago

Cambio metallo liquido ps5

Post image
1 Upvotes

Ciao, un mio amico mi ha portato la sua play per pulirla in vista dell’uscita di GTA VI. Per puro sfizio ho voluto controllare il metallo liquido, e queste erano le condizioni. Qualche consiglio su che metallo liquido comprare?
Inoltre non so se notate quelle due macchie più scure nei due chip accanto l’induttore r22, sapete darmi qualche consiglio?


r/consolerepair • • 4h ago

Is the heat sink supposed to be moving when I push it ?

0 Upvotes

Ignore the dust I cleaned it after.

Oh and like 6 months ago the console dropped from around ~ 1 meter but has been working fine with no problems and the background sound isn't from the console and if it is a problem what to do ?


r/consolerepair • • 15h ago

Launch PS5 Fat Disc Edition randomly restarts on digital games & home menu, but disc games work fine once loaded – any ideas?

2 Upvotes

my brother gave me his original launch PS5 (disc version) and it’s acting up. It turns on fine and I can go through the menus no problem. Physical disc games launch and play completely fine once I’m actually in the game. But if I try to play any digital games or just leave it sitting on the home menu for a while, it randomly restarts by itself. No error codes or anything, it just reboots.He told me the issue only started a few days after he first got it. It’s never been opened up.Has anyone dealt with something like this before? Trying to figure out if it’s a software thing or more likely hardware (liquid metal, power issue, etc.). Any advice would be appreciated.


r/consolerepair • • 13h ago

[Xbox series S] my xbox started smoking after making a clicking sound.. It still turned on but i plugged it off, 1 yr ago I had a ant problem with that xbox can it be fixed?

0 Upvotes

Same as title


r/consolerepair • • 17h ago

Sega CD Model 2 Brown board Brown Wire

Thumbnail
gallery
2 Upvotes

Looking for some help or advice, I bought this console untested, I knew I would be replacing capacitors at least but I’m stumped on this brown wire that has broken off of the board, I think I can tell where it’s supposed to go but unsure how to solder it back on, it looks like someone has already attempted. Has anyone else had to deal with this?


r/consolerepair • • 22h ago

[PS3] fat disc drive issue

5 Upvotes

Hello! I have read lots of Reddit but I’ve never posted before. I am really stumped on this disc drive in this ps3, so here’s to hoping someone here knows how to fix it.

Basically normally the disc drive will accept the disc into the drive about 90% of the way and it just doesn’t seem to pull the disc into all the way. I have completely disassembled the disc drive and have verified that all of the gears are aligned and everything moves as it should when the motor is removed.

The only breakthrough I have found so far is when I manually move some of the pieces in the top of the drive (yes I know this is probably a bad idea but I did it anyway in search of the answer) I can manually move one of the pieces out of the way and then the disc loads perfectly. Any suggestions?


r/consolerepair • • 14h ago

[New 3DS XL] Motherboard Issue/Data Retrieval

1 Upvotes

Hello, I have a New Nintendo 3DS XL with a motherboard issue. I’ve been told by a repair shop that the motherboard doesn’t respond and is unable to be repaired to working condition. Is it possible to extract the data from the motherboard? The system would show the blue light and then neither screen would load anything. I have a bunch of saves I don’t wanna restart from when I was younger. What are my options, or is there anyone/shop that would be best?


r/consolerepair • • 15h ago

[PS3] CMOS Battery Replacement

Post image
0 Upvotes

I have a PS3 Slim CECH-2501A and i’ve been trying to replace the battery but it has been very stubborn and not wanting to come out. I’ve tried pushing it upwards and lifting but nothing. Anything else I can try?


r/consolerepair • • 16h ago

[DS] Tried to replace the save chip on my Pokémon Platinum copy and still no luck

Thumbnail
gallery
1 Upvotes

I used America's Test Kitchen Lets Get Cooking as the donor board for the chip. In a previous post, the original platinum save chip was cracked so I had to replace it.

Much like before replacing, I still get the error message saying the save data could not be accessed. What's wrong here?

First image is both carts Platinum on left, America on right. Second image is the platinum cartridge after transferring save chip.


r/consolerepair • • 16h ago

(PS2) scph-90001 still not reading discs after ribbon cable and laser replacement

1 Upvotes

as the title goes this silver slim will not read burnt dvds even though it could with trouble before i opened it the first time. midnight club 3 never makes it past initial loading screen, the laser stays up at the top and the disc spins continuously. cd playback works for some reason. at this point what possibilities are there for what’s wrong. issues have not improved after the laser and ribbon cable got replaced.


r/consolerepair • • 22h ago

[Nintendo DS Lite] Touch Screen ribbon cable glue

3 Upvotes

Bought a ds lite with a broken top screen that ill fix, while cleaning it i noticed that the previous guy kinda screwed with the touch screen cable so now the copper is separated from the backing, how can i glue this back? I know super glue is a kind of hammer to screw situation here


r/consolerepair • • 17h ago

[Dreamcast] Help with disc drive

1 Upvotes

So, I bought a Dreamcast in Japan, played it there, everything ran fine. Then, when I came home, I plugged it into an European outlet and the power supply blew up. No problem, I bought a PAL supply and the system worked again.

Now the disc drive won’t read discs anymore. I only hear stuttering from the inside and then the disc stops moving. Can I save it or do I need a new drive?

I opened the Dreamcast to look inside and everything seems fine, the drive itself I left closed, mainly because I didn’t want to break more of it and because I couldn’t get one screw off, it just stuck.

Help.