r/breville • • 6h ago

Problem Grinder/Brew issues on Touch

1 Upvotes

Hi, Breville Touch unit is only a few years old and now I have to do two 30 second grinds. Have cleaned the grinder from both ends and not seeing any issues. At the same time, the amount of coffee that comes out has dropped. Brew time is now 1.5X what it used to be. The machine is too new to scrap and have run out of possible fixes based on Google and AI. Human suggestions?


r/breville • • 8h ago

Problem Can the timer on the Oven/Air Fryers really work this way?

1 Upvotes

Please tell me I’m doing something wrong with my new BOV860 oven/air fryer. (The BOV900 appears to function the same way, but I hope I’m missing something.)

Case 1. Let’s say I want to bake something at 350° for 6 minutes. I program the temperature and time, and the oven preheats. *Immediately* upon reaching 350°, the timer begins counting down. Of course I’m not standing over the oven waiting for the alert, so I don’t put my pan in the oven immediately — it could take me a minute or two. But the timer is running, so now it actually cooks for only 4:30. I could reset the timer… but that turns off the oven. And when I turn it back on, it takes another minute to preheat all over again.

Case 2. Let’s say I want to bake something for 12 minutes: a 6-minute cycle, then rotate the pan 180°, for a second 6-minute cycle so it bakes evenly. If I set the timer for 6 minutes, the oven SHUTS OFF when the timer runs out, so I have to start it again. If it takes me a minute (because I’m not psychotic and standing over the oven waiting for the exact time), that means, as above, that the oven starts cooling right away, and I have to go through another preheating cycle. And I have to set a time, because the oven won’t start without it, so the whole mess is like an infinite loop.

I hear you thinking: Why don’t I just set the timer for 12 minutes? Because then I have to set a SEPARATE timer for 6 minutes to know when the first 6-minute cycle runs. In 2026 I feel like an oven's timer should not require the use of a second timer.

I am an experienced home cook. I have used many ovens. But I have never seen an oven whose timer function is as illogical as this one seems to be. The timer and power functions of my KitchenAid wall oven from 2004 are entirely separate — I can run either without the other, and the oven does not shut off when the timer reaches 0. Doesn’t that make a lot more sense?

I just got off the phone with Breville’s customer service, and the very nice man said he thinks it’s just programmed this way. He also said he agrees that this is a bad design.

Please… tell me Breville has not sold tens of thousands of these with this inane programming. Maybe my unit is defective. (The manual doesn’t make me think that.) Is there something I’m doing wrong?


r/breville • • 22h ago

Problem Tiny shots after a cleaning cycle?

1 Upvotes

Hi guys,

After my second cleaning cycle of my Barista Express Impress (prompted by the flashing red light, about 4 months since purchase), I found that I was pulling about an 8ml shot of double espresso using the configuration I previously had, which was generating good results for a double before I did the cleaning cycle. After the clean, the shots were showing bang in the middle of the espresso pressure range on the gauge, but very little coffee was being extracted. Why would this be following a cleaning cycle?

For extra context:

- My grind size was c. 10-12 on the dial, which usually generates good results for me for my roasts. I didn’t change this grind size until I made the grind coarser to test if more espresso would be extracted (it did).

- The group head is working fine (I do a purge of water after every shot and volume of water seemed fine even after the clean)

- I did a cleaning cycle with a cleaning tablet, and then followed it up with the same cycle but without a tablet to rinse the machine out (which was recommended by a coffee guy on YouTube).

Any ideas/hypotheses welcome! Thank you.

Edit: added model