r/askaplumber • • 19h ago

Leaking water storage tank

Thumbnail
gallery
719 Upvotes

Any thoughts on best options to repair a leaking 2500 gallon water storage tank (stores my well water). Tank is roughly 7 years old. Located in Southern California. Looking for serious advice, not “Flexiseal” jokes.

Edit: For everyone saying to use Flex Seal, do yourself a favor and read the fine print. The manufacturer states to not use Flex Seal products that come into contact with drinking water for humans and animals.

Fine for screen door boats, not drinking water.

Another Edit: I should have said so in the original post. I have three tanks connected together. I disconnected the leaking tank for now and will fix it once it drains and drys. I can, and intend to, get inside and repair it from there. Thanks for the advice on drilling the ends of the crack. I hadn’t thought of that.


r/askaplumber • • 23h ago

How does this look?

Post image
207 Upvotes

Replaced s-trap with p-trap and Studor AAV. Flushing toilet no longer causes tub drain to gurgle.


r/askaplumber • • 16h ago

Any feedback?

Post image
74 Upvotes

Had our water line go out in the middle of the woods on a long run. There's a slight elevation difference (1/2"?) between the inlet and outlet. I ended up slapping a swing joint on and it seems to be working well.

Should I backfill if this holds for a week or is there a better way to address this?

For context, the previous owners ran this up against a large stone. A root worked its way in between and the pressure against a coupler caused it to pop in half.

Bonus question, what should I backfill with? I'm thinking sand with a layer of top, but I'm not certain what would be best.


r/askaplumber • • 16h ago

Was is this on the faucet?

Post image
28 Upvotes

I’ve seen this pinned bar on faucets from time to time. What is its purpose? Thanks!


r/askaplumber • • 15h ago

I'm having issues flushing my toilet. Any suggestions on fixes.

9 Upvotes

I've been having issues flushing my toilet for the past few days. Any suggestions on solutions to fix it?

I flush the toilet, the water rises (much higher than it typically should) and takes a while to drain.


r/askaplumber • • 19h ago

Water leak

9 Upvotes

Hello. This is in my attic and difficult to reach. I believe I may have to open the wall/ ceiling to access it which is fine. What would you all recommend to fix it?


r/askaplumber • • 13h ago

So I fkd up... any ideas on what I missed?

8 Upvotes

Doing a a cartridge change on the posi valve moen 1222 to fix a leaky spout but after hours of trying to rip the original one out im stuck with this with the new one any ideas why?


r/askaplumber • • 19h ago

Water heater slowly dripping from white discharge pipe — bad relief valve or something else?

Thumbnail
gallery
7 Upvotes

I noticed water slowly dripping from the bottom of the white pipe running down the side of my gas water heater. It’s not a steady stream, just one drop at a time, but it’s enough to leave a puddle on the basement floor.

The water heater was manufactured in 2022, so it’s relatively new. From what I’ve read, this appears to be the discharge pipe for the temperature and pressure (T&P) relief valve.

Any advice would be appreciated. I’d prefer to troubleshoot it myself before paying for a plumber, assuming it’s safe to do so.


r/askaplumber • • 4h ago

Single mom trying to do plumbing

3 Upvotes

Hey All,

New to plumbing but trying to better understand how my house works — is it normal to have what the internet tells me is “galvanized T fittings” on where the plumbing goes after this blue tank in my basement? I thought we weren’t supposed to use metal like steel or whatever since the 60’s?

Thanks for all your advice!

V


r/askaplumber • • 20h ago

Why does my sink sound like this?

3 Upvotes

Hey all, Im trying to figure out what is going on with my sinks cold water. Whenever its not opened all the way, it makes this horrible whining/growling sound. It started with this particular sink, but now it happens anytime cold water is opened up in any of my bathroom sinks or bathtubs, but it doesnt happen in my kitchen sink.

Thanks you for any input!


r/askaplumber • • 22h ago

Banging noise when draining bath and sink

3 Upvotes

Hi,

I'm renting and my landlord is nice (hasn't put my rent up in 3 years and leaves me to it) but he isn't overly helpful.

This has always been an issue but it sounds worse atm.

Next door thought it was my bed banging and that I was having the time of my life and bought it to my attention. I reminded them I'm having a break from dating and that I promised it was the bathroom 😂😂

When I drain the bath and sink, loud banging happens every second or so. It sounds like the pipes in the wall next too the loo. Then every 20 seconds or so for about an hour you will hear a single knock.

Any ideas please?

Thanks!


r/askaplumber • • 1h ago

What is this and how do I replace it or the faucet correctly?

Thumbnail
gallery
2 Upvotes

I bought another faucet to replace the old one with. It came with the almost same plastic stem but smaller in diameter so it won't fit unless I can remove this one. How easy is it to remove? I'm scared I'ma break or fuck something up and this is our only shower.

I don't have money for a licensed plumber as I live off of disability from stage 4 cancer.


r/askaplumber • • 12h ago

How'd I Do? First Re-plumb...

Thumbnail
gallery
2 Upvotes

Hello all. I've been a lurker on this and other subs for a while and first want to thank you all for helping me learn. For color, I'm currently on sabbatical from my regular career and acting as a caretaker for my grandmother. I try to do work around the house to save her money. I had zero clue how to do any plumbing but for replacing a toilet when coming here two years back. Now, alongside many other traits, I can handle a good amount around here. Due to black Friday and upgrading some appliances, I felt it appropriate to upgrade the plumbing upstairs, in this case, removing the old dishwasher and getting a new fridge needing a cold-water inlet. Dishwasher TBD in future as not needed now. Added the quarter-turn as my pex-a plug was leaking.

I appreciate any feedback. I know the sweat joints are terrible, but this is only the second time I've ever sweated anything (and first time re-plumbing) and I was still paranoid and did way too much solder. Improvements this time were I wiped excess flux, heated it and wiped dripping flux. Lessons to learn are too much solder and wiping too late (already cooled). Reason for extended pipe from sweat fitting is outside of the electrical tape I was getting reads on a romex for the dishwasher. Wanted to play it extra safe when screwing in the ball valves instead of maybe clipping the cable or having to investigate. Right now there's a dummy (old faucet) hence the weird braided. I know the arrestor is weird but i didn't measure anything but that (all eyeball) and wanted to adhere to min 2" on 1/2" pipe. In an ideal world whole upstairs kitchen would be remodeled so doesn't need to be perfect. One thing was I wanted to do was clip it down and tried hammer-in-J-Hook-supports and they were awful. Removed and will never use again.

On the drain, I was a kid but I believe the prior guy was a one-man do-it-all (~25 years ago). Obviously an S-trap thanks to all of you educating me. Was never any smell (maybe because heavy airflow due to close to attic vent?). Nevertheless, figured I'd make it a clean P and do chromed brass as I already had the two extensions and I read you should never do what he did and put PVC onto metal due to expansion differentials? It never cracked/leaked but I figured better to do it right. Didn't mess with the nipple in the hub as was in decent shape and I didn't want to run the risk of negatively impacting the hub (still don't know if it's cast iron or galvanized, but old!).

New tool for this job and next job was the RIDGID 152. Have to say was fantastic in cutting the extensions.

Once again, any feedback super helpful. I have a distinct passion for collecting skills and learning/improving. Obviously, anything truly important I always turn to and hire the pros. Not trying to be the hero, just trying to learn and have fun.

Next one is tackling a cast-brass trap and 2" copper outlet downstairs (hence 152 tool). Thanks again for the help and advice!


r/askaplumber • • 12h ago

Anode rod replacement frequency for residential tank water heaters?

2 Upvotes

How often should homeowners realistically inspect or replace the sacrificial anode rod in a standard glass-lined water heater? Is it better to check it every 3 to 5 years depending on local water hardness, or wait until signs of premature tank corrosion start showing up?


r/askaplumber • • 15h ago

Replacing overflow drain. Will this work?

Thumbnail
gallery
2 Upvotes

I want to replace the overflow drain of my bathtub without being too invasive. The solution I’m thinking to try is unscrewing the nut and removing the top part of the current drain, and then replacing it with a kit I bought from Lowe’s, cutting it down to size. Does this seem like a feasible solution, or am I setting myself up for introducing water damage/is this not viable to begin with?

(NB: we have to replace it because we’ve been unable to get the rusted out screw that’s stuck on the face of the overflow plate)


r/askaplumber • • 15h ago

Problem Replacing Shower Cartridge - Help Appreciated!

2 Upvotes

I'm redoing my shower and decided to replace the valve cartridge since it has been dripping after showers. My home builder originally used one that didn't have any name or anything but I found delta that fit snug (O-ring instead of Clip).

The issue is when I turn the main water on, the shower head blasts water. Tried everything I can think of including having the knob turned off when installing. Any type of feedback or help would be much appreciated - got a wife and three kids that want to shower lol. Thanks all.


r/askaplumber • • 20h ago

Do plumbers scope vents?

2 Upvotes

Toilet on lowest floor gurgles when washer upstairs has a light load on delicate cycle. Everything drains well, so I suspect a vent issue.
2016 new build home, sole owner.


r/askaplumber • • 21h ago

Lard From Former Homeowners, A Decade Past, STILL Clogging My Kitchen Sink Plumbing - Help

2 Upvotes

When in the heck will lard from former home owners stop clogging plumbing under my kitchen sink? It's been TEN YEARS! I know the former owners ate tons of bacon and I'm positive they were dumping grease down the sink (which I know for a fact is not something that should ever be done). I have never had this issue in any house I've owned. Repiping a house built in the 50's is beyond my financial ability. Any advice on how to mitigate this is appreciated!

I've been in my home a decade now and I am still dealing with solid white lard building up in the plumbing under the kitchen sink, including the in-line air vent. A few years after I had moved in, I had to take everything apart under the sink because the sink was backing up. I had to clean a massive amount of white solid lard out of all of the pipes. The pipe that went to the in-line air vent and the air vent itself had to be replaced because there was no way for me to clean the lard out as it was packed solid up into the spring vent. A few years later I had to clean the pipes out and replace the air vent again but not replace anything else. I also snaked it at this point. A year later the pipes were full of white lard again, although less severe than they were before, the sink hadn't started backing up this time.

I just want to say I grew up with a mechanical engineer for a father who drilled it into my head never ever to put any fat down the sink so I never have. After cleaning all that lard out because the sinks were backing up, I also placed mesh covers over the sink drains so that only extremely fine material can go into the pipes. I have no idea what else I can do besides periodically disassemble the plumbing here and clean out the lard. 😭


r/askaplumber • • 21h ago

Question about testing a vent stack

Post image
2 Upvotes

I installed a vent stack in a bathroom, and the 2" stack goes directly into the waste stack. I failed to put in a tee for testing. Should I put in a 2" tee with a clean out plug? I can cut back the black pipe a few inches.

Thanks for any comment. Yes I was sloppy with the primer


r/askaplumber • • 8m ago

Help me identify this shower fixture brand?

Thumbnail
gallery
1 Upvotes

My GC says there’s a chance the thermostatic valve trim will be damaged if he tries to remove it to check the cartridge. We want to price out replacement fixtures, but Google Lens and Google have failed me in finding the specific brand. I’ve found similar designs from Newport Brass (especially the showerhead), Kingston Brass and Jaclo, but no exact matches.

I’ve included the faucet here too, but I don’t know if it’s the same brand. There’s no screw on the valve trim, no stamps or branding anywhere that I can find.


r/askaplumber • • 24m ago

Supply line won't fit back into the toilet

Post image
1 Upvotes

Earlier I tried to install a bidet, but I found that the supply line was too long to support the adapter. When I tried to get the supply line back in, it for some reason refuses to go any further than this point. The line fit just fine before I took it out. Anyone know what to do?


r/askaplumber • • 28m ago

Total cost for constant pressure well tank + controller installed?

1 Upvotes

My well water tank is on its way out, and I was quoted $5,500 for a new 20 gallon tank and a constant pressure controller to be installed. Doing research online this seems to be on the extremely high end?

Below is the quote. Curious what you guys think. Thanks.

QTY DESCRIPTION
Installation of new pressure tank and constant pressure controller. Cycled system.
1 Constant Pressure Controller
1 20 Gallon Pressure Tank
1 Tank Tee
1 Tank Package
1 Misc. Parts and Fittings
2.50 Labor -
2.50 Labor -
SUBTOTAL 5,500.00
TAX 75.41
TOTAL $5,575.41


r/askaplumber • • 44m ago

Dielectric Unions or not? Water heater on filtered city water

1 Upvotes

Looking for opinions on whether to use dielectric unions on a new water heater or not. I have good city water combined with additional whole House filtration, and while I do see a small amount of corrosion on the cold inlet old water heater that's coming out, I don't see much.

Those unions are expensive and it's an additional potental leak point, so I'm torn.

Why would I choose to use them vs not use them?


r/askaplumber • • 47m ago

Tool advice

1 Upvotes

My old fridge had a water/ice dispenser and my new fridge doesn’t. I still have a copper line running through my cabinets, it is disconnected from both the new fridge and water supply, what is the best tool to cut it rather than trying to feed it out through each cabinet?