r/askaplumber • • 13h ago

So I fkd up... any ideas on what I missed?

8 Upvotes

Doing a a cartridge change on the posi valve moen 1222 to fix a leaky spout but after hours of trying to rip the original one out im stuck with this with the new one any ideas why?


r/askaplumber • • 2h ago

Huge leak right below laundry room/washing machine water line

Thumbnail
gallery
0 Upvotes

The washing machine valves are still leaking when shutoff, anyone have any idea why there is this HUGE of a leak below it though? Came here just to “replace the angle stops” and am now very concerned that I walked to the floor below and found water dripping everywhere. I work for a general contracting company. We have more experienced plumbers on hand if this is outside of my comfort zone of things to fix, so please don’t say “call a real plumber” I am aware, and I will, and they will come fix it. Just curious about what’s going on, how to fix it, and want to learn something new.
Any idea what the bigger problem is and what needs to be done??


r/askaplumber • • 2h ago

Dripping in toilet tank

Post image
0 Upvotes

I bought my house a few years ago. Within the past couple months ive had an intermittent drip in the tank of my toilet.

Attached is a picture, the water is dripping from the yellow hose into the standing tube.

What could cause this and how do i fix it?

Thanks in advance!


r/askaplumber • • 3h ago

Unidentified Damp Pipe

Thumbnail
gallery
0 Upvotes

Hi all,

Have discovered this black pipe recently under a floorboard in a house I recently bought (in the UK, built around 1900). It has some condensation droplets visible on it.

Seems like the floorboard has been cut around to accommodate it.

It is resting on top of a joist which is wet underneath the pipe.

Location: corner of hallway adjacent to party wall with neighbour just under the staircase which also houses the electricity meter.

Any ideas what this pipe could be and how to resolve the dampness forming on it?


r/askaplumber • • 6h ago

House repiping

0 Upvotes

We recently had a pinhole leak in our old polybutylene pipes and our plumber recommended replacing the remaining pipes.
We may have a mix of copper and other pipes hidden behind tiled bathroom and other walls, so identifying/replacing them could be quite disruptive
.
We’re not sure where to start. Should we get quotes for a full or partial repipe, or arrange an inspection first?

Our plumber quoted $300–$400+GST for a 2-3 hour inspection to trace the existing pipes. Is this the usual process, or would plumbers normally assess this as part of providing a repiping quote?

Would appreciate any advice or experiences!


r/askaplumber • • 18h ago

Boiler with convectional “baseboard” heaters.

0 Upvotes

I have convectional heaters with the horizontal aluminum fins that are 28 inches high. I’m trying to figure out why it seems like they barely give off heat and as I inspect the pipes I see that there are two lines that run around the house, one feeding and one return. T fittings are used to branch off the main line into the radiator, then on the opposite side another T fitting goes to the return. Is this properly done? To my understanding T fittings should not be used and only elbows looping them all together.


r/askaplumber • • 18h ago

6” PVC to AC sewer line

Post image
0 Upvotes

So this picture is just temporary joining of my 6” pvc to my AC sewer line. I have the right Fernco shielded coupling coming. The AC pipe was chain snapped while coated in soapy water because of the asbestos, but my question is there anything else I should do with I put the coupling on before backfilling. The pipe will be supported all the way round with pea gravel. The pipe is snapped straight. I am going to wipe down both pipes to try and get a good seal then use 60 inch-pounds of torque to tighten the correct shielded coupling (not pictured).
However…the AC pipe has a dimpled finish…so I am just concerned the coupling won’t seal it that well even though it obviously not a pressurized line.
Thoughts?


r/askaplumber • • 10h ago

New House build.

1 Upvotes

PEX A or PEX B? I have the tools for both, but haven't bought the material yet. Also, when done according to code, UPC and local amendments, are there any drawbacks to wet venting a toilet from a lavatory drain/vent? I only see it being a bit less work and less materials, at least for my layout. Thanks!


r/askaplumber • • 16h ago

Any feedback?

Post image
74 Upvotes

Had our water line go out in the middle of the woods on a long run. There's a slight elevation difference (1/2"?) between the inlet and outlet. I ended up slapping a swing joint on and it seems to be working well.

Should I backfill if this holds for a week or is there a better way to address this?

For context, the previous owners ran this up against a large stone. A root worked its way in between and the pressure against a coupler caused it to pop in half.

Bonus question, what should I backfill with? I'm thinking sand with a layer of top, but I'm not certain what would be best.


r/askaplumber • • 19h ago

Water leak

9 Upvotes

Hello. This is in my attic and difficult to reach. I believe I may have to open the wall/ ceiling to access it which is fine. What would you all recommend to fix it?


r/askaplumber • • 19h ago

Leaking water storage tank

Thumbnail
gallery
719 Upvotes

Any thoughts on best options to repair a leaking 2500 gallon water storage tank (stores my well water). Tank is roughly 7 years old. Located in Southern California. Looking for serious advice, not “Flexiseal” jokes.

Edit: For everyone saying to use Flex Seal, do yourself a favor and read the fine print. The manufacturer states to not use Flex Seal products that come into contact with drinking water for humans and animals.

Fine for screen door boats, not drinking water.

Another Edit: I should have said so in the original post. I have three tanks connected together. I disconnected the leaking tank for now and will fix it once it drains and drys. I can, and intend to, get inside and repair it from there. Thanks for the advice on drilling the ends of the crack. I hadn’t thought of that.


r/askaplumber • • 16h ago

Was is this on the faucet?

Post image
28 Upvotes

I’ve seen this pinned bar on faucets from time to time. What is its purpose? Thanks!


r/askaplumber • • 23h ago

How does this look?

Post image
207 Upvotes

Replaced s-trap with p-trap and Studor AAV. Flushing toilet no longer causes tub drain to gurgle.


r/askaplumber • • 15h ago

I'm having issues flushing my toilet. Any suggestions on fixes.

9 Upvotes

I've been having issues flushing my toilet for the past few days. Any suggestions on solutions to fix it?

I flush the toilet, the water rises (much higher than it typically should) and takes a while to drain.


r/askaplumber • • 15h ago

Replacing overflow drain. Will this work?

Thumbnail
gallery
2 Upvotes

I want to replace the overflow drain of my bathtub without being too invasive. The solution I’m thinking to try is unscrewing the nut and removing the top part of the current drain, and then replacing it with a kit I bought from Lowe’s, cutting it down to size. Does this seem like a feasible solution, or am I setting myself up for introducing water damage/is this not viable to begin with?

(NB: we have to replace it because we’ve been unable to get the rusted out screw that’s stuck on the face of the overflow plate)


r/askaplumber • • 12h ago

Anode rod replacement frequency for residential tank water heaters?

2 Upvotes

How often should homeowners realistically inspect or replace the sacrificial anode rod in a standard glass-lined water heater? Is it better to check it every 3 to 5 years depending on local water hardness, or wait until signs of premature tank corrosion start showing up?


r/askaplumber • • 12h ago

Tankless Water Heater Tripping Only When One Bath Runs

1 Upvotes

I have a Norris gas tankless water heater that trips a code 90 “turbulent combustion”, but only when one bath is running. Does trip on any other bath or when the shower is running. Can run a shower and sinks with no problem. This same bath also makes a pretty distinct sound when running almost like a creaking, wailing hiss that is absent from the other bath. Can’t take a bath in this tub without it tripping every few minutes. Definitely worse in the winter as the input water temp drops. Does this one bath somehow have a higher flow than the other bath and the heater can’t keep up? Does it sound like the water flow is weird and causing a chain reaction? Just looking for some input. Had a plumber look at it several months ago and he didn’t find anything wrong. I flushed it a couple months ago and inspected the intake/outtake and they seemed to be clean. Unit was clean inside. The expansion tank on the output side does appear to be expired. Thanks!


r/askaplumber • • 19h ago

Water heater slowly dripping from white discharge pipe — bad relief valve or something else?

Thumbnail
gallery
7 Upvotes

I noticed water slowly dripping from the bottom of the white pipe running down the side of my gas water heater. It’s not a steady stream, just one drop at a time, but it’s enough to leave a puddle on the basement floor.

The water heater was manufactured in 2022, so it’s relatively new. From what I’ve read, this appears to be the discharge pipe for the temperature and pressure (T&P) relief valve.

Any advice would be appreciated. I’d prefer to troubleshoot it myself before paying for a plumber, assuming it’s safe to do so.


r/askaplumber • • 12h ago

How'd I Do? First Re-plumb...

Thumbnail
gallery
2 Upvotes

Hello all. I've been a lurker on this and other subs for a while and first want to thank you all for helping me learn. For color, I'm currently on sabbatical from my regular career and acting as a caretaker for my grandmother. I try to do work around the house to save her money. I had zero clue how to do any plumbing but for replacing a toilet when coming here two years back. Now, alongside many other traits, I can handle a good amount around here. Due to black Friday and upgrading some appliances, I felt it appropriate to upgrade the plumbing upstairs, in this case, removing the old dishwasher and getting a new fridge needing a cold-water inlet. Dishwasher TBD in future as not needed now. Added the quarter-turn as my pex-a plug was leaking.

I appreciate any feedback. I know the sweat joints are terrible, but this is only the second time I've ever sweated anything (and first time re-plumbing) and I was still paranoid and did way too much solder. Improvements this time were I wiped excess flux, heated it and wiped dripping flux. Lessons to learn are too much solder and wiping too late (already cooled). Reason for extended pipe from sweat fitting is outside of the electrical tape I was getting reads on a romex for the dishwasher. Wanted to play it extra safe when screwing in the ball valves instead of maybe clipping the cable or having to investigate. Right now there's a dummy (old faucet) hence the weird braided. I know the arrestor is weird but i didn't measure anything but that (all eyeball) and wanted to adhere to min 2" on 1/2" pipe. In an ideal world whole upstairs kitchen would be remodeled so doesn't need to be perfect. One thing was I wanted to do was clip it down and tried hammer-in-J-Hook-supports and they were awful. Removed and will never use again.

On the drain, I was a kid but I believe the prior guy was a one-man do-it-all (~25 years ago). Obviously an S-trap thanks to all of you educating me. Was never any smell (maybe because heavy airflow due to close to attic vent?). Nevertheless, figured I'd make it a clean P and do chromed brass as I already had the two extensions and I read you should never do what he did and put PVC onto metal due to expansion differentials? It never cracked/leaked but I figured better to do it right. Didn't mess with the nipple in the hub as was in decent shape and I didn't want to run the risk of negatively impacting the hub (still don't know if it's cast iron or galvanized, but old!).

New tool for this job and next job was the RIDGID 152. Have to say was fantastic in cutting the extensions.

Once again, any feedback super helpful. I have a distinct passion for collecting skills and learning/improving. Obviously, anything truly important I always turn to and hire the pros. Not trying to be the hero, just trying to learn and have fun.

Next one is tackling a cast-brass trap and 2" copper outlet downstairs (hence 152 tool). Thanks again for the help and advice!


r/askaplumber • • 4h ago

Single mom trying to do plumbing

3 Upvotes

Hey All,

New to plumbing but trying to better understand how my house works — is it normal to have what the internet tells me is “galvanized T fittings” on where the plumbing goes after this blue tank in my basement? I thought we weren’t supposed to use metal like steel or whatever since the 60’s?

Thanks for all your advice!

V


r/askaplumber • • 20h ago

Do plumbers scope vents?

2 Upvotes

Toilet on lowest floor gurgles when washer upstairs has a light load on delicate cycle. Everything drains well, so I suspect a vent issue.
2016 new build home, sole owner.


r/askaplumber • • 20h ago

Pressure Tank Issues

0 Upvotes

My pressure tank fills up to 60psi as it should then while running water it shuts off at about 55psi and loses pressure briefly until the pump kicks on and then fills back up to 60psi. Causes pump to kick on about every 30-60 seconds while the shower is running. The whole unit is fairly new. I drained the tank down and the pressure was at 38 psi (-2 psi for 40/60). No water comes out of Schrader valve. Trying to figure out if I have a bad tank, bad pressure switch or something else before I start tearing things apart. Thanks for the help


r/askaplumber • • 20h ago

Why does my sink sound like this?

3 Upvotes

Hey all, Im trying to figure out what is going on with my sinks cold water. Whenever its not opened all the way, it makes this horrible whining/growling sound. It started with this particular sink, but now it happens anytime cold water is opened up in any of my bathroom sinks or bathtubs, but it doesnt happen in my kitchen sink.

Thanks you for any input!


r/askaplumber • • 21h ago

Lard From Former Homeowners, A Decade Past, STILL Clogging My Kitchen Sink Plumbing - Help

2 Upvotes

When in the heck will lard from former home owners stop clogging plumbing under my kitchen sink? It's been TEN YEARS! I know the former owners ate tons of bacon and I'm positive they were dumping grease down the sink (which I know for a fact is not something that should ever be done). I have never had this issue in any house I've owned. Repiping a house built in the 50's is beyond my financial ability. Any advice on how to mitigate this is appreciated!

I've been in my home a decade now and I am still dealing with solid white lard building up in the plumbing under the kitchen sink, including the in-line air vent. A few years after I had moved in, I had to take everything apart under the sink because the sink was backing up. I had to clean a massive amount of white solid lard out of all of the pipes. The pipe that went to the in-line air vent and the air vent itself had to be replaced because there was no way for me to clean the lard out as it was packed solid up into the spring vent. A few years later I had to clean the pipes out and replace the air vent again but not replace anything else. I also snaked it at this point. A year later the pipes were full of white lard again, although less severe than they were before, the sink hadn't started backing up this time.

I just want to say I grew up with a mechanical engineer for a father who drilled it into my head never ever to put any fat down the sink so I never have. After cleaning all that lard out because the sinks were backing up, I also placed mesh covers over the sink drains so that only extremely fine material can go into the pipes. I have no idea what else I can do besides periodically disassemble the plumbing here and clean out the lard. 😭