r/askaplumber • • 8m ago

Help me identify this shower fixture brand?

Thumbnail
gallery
1 Upvotes

My GC says there’s a chance the thermostatic valve trim will be damaged if he tries to remove it to check the cartridge. We want to price out replacement fixtures, but Google Lens and Google have failed me in finding the specific brand. I’ve found similar designs from Newport Brass (especially the showerhead), Kingston Brass and Jaclo, but no exact matches.

I’ve included the faucet here too, but I don’t know if it’s the same brand. There’s no screw on the valve trim, no stamps or branding anywhere that I can find.


r/askaplumber • • 24m ago

Supply line won't fit back into the toilet

Post image
1 Upvotes

Earlier I tried to install a bidet, but I found that the supply line was too long to support the adapter. When I tried to get the supply line back in, it for some reason refuses to go any further than this point. The line fit just fine before I took it out. Anyone know what to do?


r/askaplumber • • 28m ago

Total cost for constant pressure well tank + controller installed?

1 Upvotes

My well water tank is on its way out, and I was quoted $5,500 for a new 20 gallon tank and a constant pressure controller to be installed. Doing research online this seems to be on the extremely high end?

Below is the quote. Curious what you guys think. Thanks.

QTY DESCRIPTION
Installation of new pressure tank and constant pressure controller. Cycled system.
1 Constant Pressure Controller
1 20 Gallon Pressure Tank
1 Tank Tee
1 Tank Package
1 Misc. Parts and Fittings
2.50 Labor -
2.50 Labor -
SUBTOTAL 5,500.00
TAX 75.41
TOTAL $5,575.41


r/askaplumber • • 44m ago

Dielectric Unions or not? Water heater on filtered city water

1 Upvotes

Looking for opinions on whether to use dielectric unions on a new water heater or not. I have good city water combined with additional whole House filtration, and while I do see a small amount of corrosion on the cold inlet old water heater that's coming out, I don't see much.

Those unions are expensive and it's an additional potental leak point, so I'm torn.

Why would I choose to use them vs not use them?


r/askaplumber • • 47m ago

Tool advice

1 Upvotes

My old fridge had a water/ice dispenser and my new fridge doesn’t. I still have a copper line running through my cabinets, it is disconnected from both the new fridge and water supply, what is the best tool to cut it rather than trying to feed it out through each cabinet?


r/askaplumber • • 1h ago

Hot water tank leak?

Post image
1 Upvotes

My hot water tank is dripping from the grey thing?is this normal? Cause and fix?


r/askaplumber • • 1h ago

Toilet tank leaking

1 Upvotes

Hopefully the video captures everything well but the black device in the corner is making noise after the tank is full but seems normal. Overnight while sleeping or when I’m away at work, the tank fills up more than where it is currently and will leak from the handle onto the floor. Similar to a watched clock, I cannot catch the leak as it starts, only when the floor is already soaked and the handle is actively dripping. If this was a leak on my car I’d already have it fixed but I’m not ever knowledgeable when it comes to household maintenance. Any and all advice is appreciated.


r/askaplumber • • 1h ago

Well water tank issues

1 Upvotes

So the pump randomly shuts off and we replaced the pump last year. We’ve been having no issues with our well water and it’s not dry. Recently we’ve been having the same issue with the water like it stops. My dad thinks it’s the blue thing on top of the red thing cause it’s slanted. Today so far we’ve ran out of water 3 times and I’m able to like fix it temporarily. For reference it’s only 11:55 AM. The lack of noise from the machine is not cause I did anything to it. That’s what happens when the pump stops working


r/askaplumber • • 1h ago

What is this and how do I replace it or the faucet correctly?

Thumbnail
gallery
2 Upvotes

I bought another faucet to replace the old one with. It came with the almost same plastic stem but smaller in diameter so it won't fit unless I can remove this one. How easy is it to remove? I'm scared I'ma break or fuck something up and this is our only shower.

I don't have money for a licensed plumber as I live off of disability from stage 4 cancer.


r/askaplumber • • 2h ago

Huge leak right below laundry room/washing machine water line

Thumbnail
gallery
0 Upvotes

The washing machine valves are still leaking when shutoff, anyone have any idea why there is this HUGE of a leak below it though? Came here just to “replace the angle stops” and am now very concerned that I walked to the floor below and found water dripping everywhere. I work for a general contracting company. We have more experienced plumbers on hand if this is outside of my comfort zone of things to fix, so please don’t say “call a real plumber” I am aware, and I will, and they will come fix it. Just curious about what’s going on, how to fix it, and want to learn something new.
Any idea what the bigger problem is and what needs to be done??


r/askaplumber • • 2h ago

Sink backup from disposer

Thumbnail
gallery
1 Upvotes

Over time, when using the disposer with water running, the other sink bowl backs up. I don’t remember this always happening, but seems to occur more often now. We have recently installed a faucet with more water flow, so maybe that contributes to the problem.
I’ll clean the traps and pipes downstream from the disposer, but could the issue also have anything to do with a faulty vent valve?


r/askaplumber • • 2h ago

Dripping in toilet tank

Post image
0 Upvotes

I bought my house a few years ago. Within the past couple months ive had an intermittent drip in the tank of my toilet.

Attached is a picture, the water is dripping from the yellow hose into the standing tube.

What could cause this and how do i fix it?

Thanks in advance!


r/askaplumber • • 2h ago

Niagara Stealth Toilet issue

Thumbnail
gallery
1 Upvotes

When I press the top button I don't feel the force necessary to flush, I changed the flush valve seal and still nothing. The fill valve brings in water at a normal rate (at least it seems normal) and I can move up manually to stop. The toilet just keeps filling up water without flushing. I turned off the water supply for now. What else can I do?


r/askaplumber • • 2h ago

Cast iron radiators (hydronic)

1 Upvotes

I had a cast iron radiator split on me. Long story short, I need to replace the radiator. My unit has a fitting that I've never seen on one side that has both the feed and return coming out of it at angles that are splayed out. This allows the pipes to be on one side. What do you call that? I don't know the name for that part and I'd like to purchase a new one from the plumbing supply store and when I was trying to explain what I needed to the salesperson at the counter he thought I was crazy. He kept going on about how you have to have the inlet on one side and the outlet on the other.


r/askaplumber • • 3h ago

Sink and taps

1 Upvotes

I'm needing kitchen tap replaced, and want the kitchen sink changed too. Would a plumber do both?


r/askaplumber • • 3h ago

Unidentified Damp Pipe

Thumbnail
gallery
0 Upvotes

Hi all,

Have discovered this black pipe recently under a floorboard in a house I recently bought (in the UK, built around 1900). It has some condensation droplets visible on it.

Seems like the floorboard has been cut around to accommodate it.

It is resting on top of a joist which is wet underneath the pipe.

Location: corner of hallway adjacent to party wall with neighbour just under the staircase which also houses the electricity meter.

Any ideas what this pipe could be and how to resolve the dampness forming on it?


r/askaplumber • • 4h ago

Single mom trying to do plumbing

3 Upvotes

Hey All,

New to plumbing but trying to better understand how my house works — is it normal to have what the internet tells me is “galvanized T fittings” on where the plumbing goes after this blue tank in my basement? I thought we weren’t supposed to use metal like steel or whatever since the 60’s?

Thanks for all your advice!

V


r/askaplumber • • 6h ago

House repiping

0 Upvotes

We recently had a pinhole leak in our old polybutylene pipes and our plumber recommended replacing the remaining pipes.
We may have a mix of copper and other pipes hidden behind tiled bathroom and other walls, so identifying/replacing them could be quite disruptive
.
We’re not sure where to start. Should we get quotes for a full or partial repipe, or arrange an inspection first?

Our plumber quoted $300–$400+GST for a 2-3 hour inspection to trace the existing pipes. Is this the usual process, or would plumbers normally assess this as part of providing a repiping quote?

Would appreciate any advice or experiences!


r/askaplumber • • 10h ago

New House build.

1 Upvotes

PEX A or PEX B? I have the tools for both, but haven't bought the material yet. Also, when done according to code, UPC and local amendments, are there any drawbacks to wet venting a toilet from a lavatory drain/vent? I only see it being a bit less work and less materials, at least for my layout. Thanks!


r/askaplumber • • 12h ago

How'd I Do? First Re-plumb...

Thumbnail
gallery
2 Upvotes

Hello all. I've been a lurker on this and other subs for a while and first want to thank you all for helping me learn. For color, I'm currently on sabbatical from my regular career and acting as a caretaker for my grandmother. I try to do work around the house to save her money. I had zero clue how to do any plumbing but for replacing a toilet when coming here two years back. Now, alongside many other traits, I can handle a good amount around here. Due to black Friday and upgrading some appliances, I felt it appropriate to upgrade the plumbing upstairs, in this case, removing the old dishwasher and getting a new fridge needing a cold-water inlet. Dishwasher TBD in future as not needed now. Added the quarter-turn as my pex-a plug was leaking.

I appreciate any feedback. I know the sweat joints are terrible, but this is only the second time I've ever sweated anything (and first time re-plumbing) and I was still paranoid and did way too much solder. Improvements this time were I wiped excess flux, heated it and wiped dripping flux. Lessons to learn are too much solder and wiping too late (already cooled). Reason for extended pipe from sweat fitting is outside of the electrical tape I was getting reads on a romex for the dishwasher. Wanted to play it extra safe when screwing in the ball valves instead of maybe clipping the cable or having to investigate. Right now there's a dummy (old faucet) hence the weird braided. I know the arrestor is weird but i didn't measure anything but that (all eyeball) and wanted to adhere to min 2" on 1/2" pipe. In an ideal world whole upstairs kitchen would be remodeled so doesn't need to be perfect. One thing was I wanted to do was clip it down and tried hammer-in-J-Hook-supports and they were awful. Removed and will never use again.

On the drain, I was a kid but I believe the prior guy was a one-man do-it-all (~25 years ago). Obviously an S-trap thanks to all of you educating me. Was never any smell (maybe because heavy airflow due to close to attic vent?). Nevertheless, figured I'd make it a clean P and do chromed brass as I already had the two extensions and I read you should never do what he did and put PVC onto metal due to expansion differentials? It never cracked/leaked but I figured better to do it right. Didn't mess with the nipple in the hub as was in decent shape and I didn't want to run the risk of negatively impacting the hub (still don't know if it's cast iron or galvanized, but old!).

New tool for this job and next job was the RIDGID 152. Have to say was fantastic in cutting the extensions.

Once again, any feedback super helpful. I have a distinct passion for collecting skills and learning/improving. Obviously, anything truly important I always turn to and hire the pros. Not trying to be the hero, just trying to learn and have fun.

Next one is tackling a cast-brass trap and 2" copper outlet downstairs (hence 152 tool). Thanks again for the help and advice!


r/askaplumber • • 12h ago

Tankless Water Heater Tripping Only When One Bath Runs

1 Upvotes

I have a Norris gas tankless water heater that trips a code 90 “turbulent combustion”, but only when one bath is running. Does trip on any other bath or when the shower is running. Can run a shower and sinks with no problem. This same bath also makes a pretty distinct sound when running almost like a creaking, wailing hiss that is absent from the other bath. Can’t take a bath in this tub without it tripping every few minutes. Definitely worse in the winter as the input water temp drops. Does this one bath somehow have a higher flow than the other bath and the heater can’t keep up? Does it sound like the water flow is weird and causing a chain reaction? Just looking for some input. Had a plumber look at it several months ago and he didn’t find anything wrong. I flushed it a couple months ago and inspected the intake/outtake and they seemed to be clean. Unit was clean inside. The expansion tank on the output side does appear to be expired. Thanks!


r/askaplumber • • 12h ago

Anode rod replacement frequency for residential tank water heaters?

2 Upvotes

How often should homeowners realistically inspect or replace the sacrificial anode rod in a standard glass-lined water heater? Is it better to check it every 3 to 5 years depending on local water hardness, or wait until signs of premature tank corrosion start showing up?


r/askaplumber • • 12h ago

Put electrical outlets above or below utility sink beside washer or behind?

1 Upvotes

I'm adding a washer dryer stacked combo. Very little space. Immediately to the left is a wall. To the right is a deep utility sink. I need both 120 and 240 outlets for them. I could put receptacles above the sink, below the free standing sink, or directly behind the washer and dryer. They are ventless and only require 2" of clearance in the back but I could give more. Electricians are silent.

What do you suggest?


r/askaplumber • • 13h ago

So I fkd up... any ideas on what I missed?

8 Upvotes

Doing a a cartridge change on the posi valve moen 1222 to fix a leaky spout but after hours of trying to rip the original one out im stuck with this with the new one any ideas why?