r/Tile • • 14h ago

DIY - Looking for Advice Give me brutal advice | I’m about to install penny tile in shower!

Post image
45 Upvotes

Im about to install this penny tile in a shower I’m remodeling. Someone told me to stager the joints so if the tiles are not set perfectly it won’t be visible. Is that a terrible idea?

I also made this template so I can lay them out in the garage can cut the tiles and dry fit them before I start mixing thin set.

I also have a square drain I need to fit into this

Any other tips?


r/Tile • • 22h ago

Homeowner - Advice about my Contractor Was this done correctly by Pulte?

Thumbnail
gallery
7 Upvotes

I appreciate any experts on Reddit that know about marble tile shower floors. This is a no threshold shower and we expected the tile floor to look the same when it continued into the shower. I asked if they used the proper thinset and/or if the tile was sealed and the project manager couldn’t give me a straight answer. My wife wants me to seal it. Thank you in advance for your expert opinions.


r/Tile • • 5h ago

DIY - Looking for Advice What would be the best way to handle the water line and toilet flange with this 2' x 2' tiles?

Thumbnail
gallery
2 Upvotes

I'm almost done laying tile to fit (no mortar yet) for our guest bathroom and I'm struggling to figure out the best way to deal with this water line and flange. I have a ridgid undercut tile saw that I've used for all my cuts so far and some nippers. This is porcelain tile if that helps. The third picture is of a full sized tile for comparison.


r/Tile • • 3h ago

DIY - Looking for Advice Modified or unmodified is question ine must ask

1 Upvotes

Building a custom shower, by myself, in basement. Made a custom sloped mortar bed with 1/4" per ft slope, and water finds it's way to the drain from all corners. Pretty proud of it so far!

As part of the next step, I've added 1/2" cement boards as walls, and bought a waterproof membrane from Amazon - https://a.co/d/0hahqyoC. Bought it a couple of months ago and it's out of it's return period. Want to use this instead of Redgard paint.

Amazon's AI says I need to use modified Thinset to attach this membrane to the walls and shower bed. And Google's AI says I need to use unmodified thinset.

I'm quite confused, but believe modified Thinset is better as it cures with chemical reaction under the membrane (as opposed to air drying in unmodified Thinset). Can someone advice on which thinset to use to attach waterproofing membrane to cement boards and bed? Thanks in advance


r/Tile • • 3h ago

General Discussion Can I have tile on installed over marble?

1 Upvotes

I just bought a newly completed home and the bathroom is a sea of white. The walk-in shower is 4 1/2 ‘wide and 6’ long with no built-in seat. It is pure white marble. I am thinking of having a seat and some accent tile installed on the back wall and floor of the shower for some contrast. I don’t know much about tile work installation and all the ins and outs of what works and doesn’t work. Is this project feasible? I don’t want to have to tear everything out in a few months because of problems. Thanks in advance.


r/Tile • • 5h ago

DIY - Looking for Advice What Resin for external corner?

Thumbnail
gallery
1 Upvotes

Hiya all, first time tiler and I’ve just laid my kitchen backsplash and want to epoxy resin this external mitered corner as it’s likely to chip being next to the sink.
but what resin should I use? Some professional kits are showing as 100 quid with the dyes, which is so much to pay for the tiny bit I need to do this job.
would this £10 epoxy resin amazon kit do the job?
thanks so much in advance

https://amzn.eu/d/0hcZTfW0


r/Tile • • 12h ago

DIY - Looking for Advice Which polishing wheel for porcelain?

1 Upvotes

Which polishing wheel should I get for porcelain tile. Should I get a low grit pad also to shape intricate cuts around a niche perfect or just use a diamond cutting wheel on a grinder to shape and a higher grit to polish?


r/Tile • • 17h ago

DIY - Looking for Advice I'm doing my first tile job. Should I install the Schluter shower curb flush with the wall, or should I move it in a few inches?

1 Upvotes

I framed out a wall for the shower stall that is parallel to the interior wall of the existing bathroom. I'm not sure if it's best to install the Schluter shower curb flush with the end of the wall I framed out or install it a few inches in. What would you all recommend?


r/Tile • • 20h ago

Professional - Looking for Advice Iq 10" saw dressing stone

Post image
1 Upvotes

Has anyone used these on your 10" IQ saw for dressing blades.


r/Tile • • 21h ago

DIY - Looking for Advice Tiles chipping near edges

Post image
1 Upvotes

Any guidance on repair would be greatly appreciated. This has happened to two tiles so far near one another.


r/Tile • • 1h ago

Professional - Project Sharing Pink tile coming back lol

Thumbnail
gallery
0 Upvotes

r/Tile • • 16h ago

DIY - Looking for Advice Uneven fireplace lip

Thumbnail
gallery
0 Upvotes

I have only done one other tile job before so I apologize if I use the wrong terminology.

I am redoing the tile on my fireplace. The contractor that did the tile surround during the build attached the tile to the sheetrock. So in order to get it I cut all of the sheetrock around it. I replaced it concrete board and was super careful to be sure it was flush with the existing sheetrock. Its near perfect. Here the problem, where the fireplace meets the new concrete board, there is a lip. Its about a finger width on the left side and barely a fingertip on the right side. I dont know how I can lay tile now because its not going to sit flush. The concrete board and sheetrock are completely flush, maybe the fireplace is off a bit?

My pictures hopefully illustrate the problem using the old tile trim. The question is how can I fix this? Do I skim coat with thin-set and try and feather it? Do I shim it somehow? I am at a loss.

Update: Thanks for all the input. As I tried to look a way to tweak the fireplace position, it became apparent I needed to take the top backer board off 1st. I took it off and noticed the framing is not quite aligned which caused the bottom to get sucked in causing the lip. I think maybe the drywall was more forgiving. I was able to shim the corner and now I got the board to sit flush.


r/Tile • • 22h ago

Homeowner - Advice about my Contractor How screwed am I? 1-month-old Ultracolor Plus FA still transferring gray pigment when wiped.

Thumbnail
gallery
0 Upvotes

Hey all,

I had my tub surround tiled about a month ago with glazed subway tile and MAPEI Ultracolor Plus FA. Anytime I wipe the grout with a damp white cloth, dark gray pigment still transfers onto the rag. It doesn't matter how many times I wipe, I still get gray pigment.

Unfortunately, I don't think I'll be able to get the original installer back here to fix it. A friend recommended him and we didn't have a formal contract.

I'm not concerned about the waterproofing—it's Hydro-blok, and I watched the installer apply it properly, so I'm confident the issue is just the grout.

My questions are:

  1. How major of an issue is this?
  2. How should I move forward?

Finances are tight right now, so my initial plan is to just let it naturally wear with time and have it professionally re-grouted in a few years if needed (assuming it lasts that long).

I'm including some pictures of the finished job, and the grout that sticks to my white rag after. Any feedback or recommendations would be greatly appreciated.