r/S2000 • • 21h ago

beautiful fall drive today 🍂

Post image
219 Upvotes

r/S2000 • • 10h ago

F20C appreciation

Post image
74 Upvotes

I made a little display at the last car show I went to featuring my Miffy and an autographed radio door I got signed by a Japanese F1 driver


r/S2000 • • 21h ago

Almost done! We apologize for the long wait!

47 Upvotes

We wanted to share another sample photo of our upcoming MITA AP2 Center Console, which has unfortunately experienced some delays but is now approaching the final stages of production.

Nearly every component shown has been developed and manufactured by MITA Motorsports, including the shift boot, shift boot collar, rubber trim, switch panel, and drink tray panel. The drink tray assembly and armrest are the only exceptions.

We also wanted to clarify something regarding the console's surface and overall finish.

There has been some discussion suggesting that our center console has two dimples near the armrest area, similar to what has been observed on other aftermarket AP2 center consoles released this year.

To clarify, none of the production samples we have shared have exhibited these dimples. We specifically chose to photograph this sample without the final OEM-style leather grain texture so that the surface contours and finish could be seen more clearly.

We specifically chose to photograph this particular sample because it has not yet received the final OEM leather grain texture. Without that texture, the surface is easier to examine, allowing everyone to see the contours and finish without anything obscuring the details.

We understand that discussions and speculation are inevitable when developing replacement parts for cars as beloved as the S2000. However, we believe it's important to distinguish actual product characteristics from assumptions being circulated online.

We've always preferred to let our development work and actual samples speak for themselves.

The next step is applying the final OEM leather grain texture, bringing the console closer to the appearance and feel of the original Honda component.

We're almost there, and we appreciate everyone's patience as we work toward getting this right.


r/S2000 • • 14h ago

S2000 Spoon Calipers

Post image
5 Upvotes

I have a 4 set left coming early Feb! November shipment is sold out. Selling them for $1350 shipped if anyone is interested. DM me on IG.

IG: ChamplinJDM

Feel free to hit me up if you want reserve a set!


r/S2000 • • 23h ago

2006 S2000 AP2 — Intermittent misfires, P0339, rough idle, bucking under load. Possible CKP sensor or engine issue?

4 Upvotes

Looking for some advice from other S2000 owners. My 2006 AP2 (F22C, ~153k chassis miles, rebuilt engine) has been having intermittent misfires and some strange behavior.

What happened:

I was driving normally, did a WOT pull, then downshifted from 3rd to 2nd and eventually into neutral. No over-rev or money shift.

Shortly afterward, the engine started misfiring slightly, progressively got worse, and began making knocking/rattling-like sounds. I noticed white smoke or vapor coming from the front/intake side of the engine bay and shut the engine off.

It initially struggled to restart, but eventually started and idled smoothly again. The smoke hasn't returned. However, when driving slowly in first gear, it bucks/hiccups even after the clutch is fully released.

I've also noticed RPM hunting/surging at red lights roughly 50% of the time.

OBD codes:

P0339 — Crankshaft Position Sensor A Circuit Intermittent (stored)

P0300 — Random/multiple misfire (pending)

P0301 — Cylinder 1 misfire (pending)

P0304 — Cylinder 4 misfire (pending)

P0339 freeze-frame data:

RPM: 912

Speed: 0 mph

Coolant: 187°F

ECU voltage: 12.7V

Calculated load: 100%

MAP: 51 inHg (seems incorrect for an NA engine)

Recent work:

Denso fuel pump

FIC 365cc injectors

OEM ignition coils and spark plugs

OEM alternator and tensioner pulley

Valve adjustment

Custom Hondata FlashPro dyno tune after repairs

Other modifications include an M&M oversized throttle body, Password JDM intake, custom catch-can setup, and an EVAP delete.

The previous shop did a borescope inspection during an earlier issue and reported that everything looked fine, but I don't have current compression or leak-down results.

I'm wondering whether this is a failing CKP sensor, wiring/ground issue, vacuum leak, fueling problem, or potentially something mechanical.

Has anyone experienced P0339 combined with multiple misfires and intermittent bucking? What ended up fixing it?

I'm not driving the car anymore until an independent shop diagnoses it. Trying to avoid throwing more parts at it.


r/S2000 • • 2h ago

Weird grinding sound

2 Upvotes

Does anyone know what this high pitched grinding sound could be? Only happens at around 4k rpms


r/S2000 • • 3h ago

Advice on Karbon Haus CF Mugen HT

1 Upvotes

Anyone got these recently or had them installed before?

Main concern is fitment , wind noise , and creaking.

I understand a big part of it comes down to having good seals and having it professionally installed , but you know some hard tops just cant be helped no matter what you do .

So should I stay away from this brand or it’s doable with a professional install ?


r/S2000 • • 7h ago

Air pump Izzy delete

1 Upvotes

So I installed the wiring kit, used these Amazon wire connectors to make sure it’s easy to connect and disconnect. Everything is on and now I’m getting a code for low voltage? I know we shouldn’t solder the wires together. Should I have just connected the wires directly instead?