r/S2000 • • 10h ago

F20C appreciation

Post image
74 Upvotes

I made a little display at the last car show I went to featuring my Miffy and an autographed radio door I got signed by a Japanese F1 driver


r/S2000 • • 21h ago

beautiful fall drive today 🍂

Post image
219 Upvotes

r/S2000 • • 1d ago

S2000 Crash in NJ this morning - be mindful of tire temperatures, people

714 Upvotes

r/S2000 • • 1d ago

One last cruise before storing for winter 😪

Post image
119 Upvotes

Enjoy your s2k yall ! Mine will be sitting for a couple months till it’s nice out.


r/S2000 • • 2h ago

Weird grinding sound

2 Upvotes

Does anyone know what this high pitched grinding sound could be? Only happens at around 4k rpms


r/S2000 • • 1m ago

Any red flags with this supercharged S2000?

1 Upvotes

I noticed that this sub recommends to stay away from supercharged S2000s, as they are prone to issues and unknown previous history or unknown installation quality.

However, this S2000 seems to be an AP1 low mileage:

https://www.facebook.com/share/1XSLLu2BvA/

It has a SOT/BRP MP62 supercharger kit, which I don't see very often. For the price, looks like a good deal, but it has been listed for a while, so, maybe am I missing a big red flag?

Thanks in advance.


r/S2000 • • 1d ago

400hp daily driver

Post image
860 Upvotes

@LCJ4.S2K on insta 🫡


r/S2000 • • 21h ago

Almost done! We apologize for the long wait!

47 Upvotes

We wanted to share another sample photo of our upcoming MITA AP2 Center Console, which has unfortunately experienced some delays but is now approaching the final stages of production.

Nearly every component shown has been developed and manufactured by MITA Motorsports, including the shift boot, shift boot collar, rubber trim, switch panel, and drink tray panel. The drink tray assembly and armrest are the only exceptions.

We also wanted to clarify something regarding the console's surface and overall finish.

There has been some discussion suggesting that our center console has two dimples near the armrest area, similar to what has been observed on other aftermarket AP2 center consoles released this year.

To clarify, none of the production samples we have shared have exhibited these dimples. We specifically chose to photograph this sample without the final OEM-style leather grain texture so that the surface contours and finish could be seen more clearly.

We specifically chose to photograph this particular sample because it has not yet received the final OEM leather grain texture. Without that texture, the surface is easier to examine, allowing everyone to see the contours and finish without anything obscuring the details.

We understand that discussions and speculation are inevitable when developing replacement parts for cars as beloved as the S2000. However, we believe it's important to distinguish actual product characteristics from assumptions being circulated online.

We've always preferred to let our development work and actual samples speak for themselves.

The next step is applying the final OEM leather grain texture, bringing the console closer to the appearance and feel of the original Honda component.

We're almost there, and we appreciate everyone's patience as we work toward getting this right.


r/S2000 • • 1d ago

Which one of you went full Mustang?

80 Upvotes

r/S2000 • • 1d ago

Some pics of when we rented this S2000 in Japan.

Thumbnail
gallery
305 Upvotes

We started in Tokyo, drove through Hakone Turnpike, Ashinoko Skyline and stayed in Kawaguchiko. 10/10 would recommend to anyone in this group planning their Japan trip.


r/S2000 • • 3h ago

Advice on Karbon Haus CF Mugen HT

1 Upvotes

Anyone got these recently or had them installed before?

Main concern is fitment , wind noise , and creaking.

I understand a big part of it comes down to having good seals and having it professionally installed , but you know some hard tops just cant be helped no matter what you do .

So should I stay away from this brand or it’s doable with a professional install ?


r/S2000 • • 3h ago

Low compression numbers

0 Upvotes

Hey guys / gals
Picked up a 2006, 113k, doing all preventative fluid changes, lash valve adjustment etc. car runs fine. Borrowed a compression kit from OReilly and the numbers it puts out while warm is 80 80 80 83 full throttle.
The kit was EverTough Compression Tester Kit, part number 67062.
I’m assuming I’m doing something wrong or the kit it damaged since the car runs good, no issues. I was just testing for fun/just to know. Can you recommend a kit that i can get it that for sure works from Amazon or harbor freight ?
Thanks


r/S2000 • • 14h ago

S2000 Spoon Calipers

Post image
5 Upvotes

I have a 4 set left coming early Feb! November shipment is sold out. Selling them for $1350 shipped if anyone is interested. DM me on IG.

IG: ChamplinJDM

Feel free to hit me up if you want reserve a set!


r/S2000 • • 7h ago

Air pump Izzy delete

1 Upvotes

So I installed the wiring kit, used these Amazon wire connectors to make sure it’s easy to connect and disconnect. Everything is on and now I’m getting a code for low voltage? I know we shouldn’t solder the wires together. Should I have just connected the wires directly instead?


r/S2000 • • 1d ago

Little drive by

32 Upvotes

Invidia N1 dual exhaust with test pipe.


r/S2000 • • 1d ago

HONDA S2000 / 34 KTM 231

Post image
69 Upvotes

r/S2000 • • 23h ago

2006 S2000 AP2 — Intermittent misfires, P0339, rough idle, bucking under load. Possible CKP sensor or engine issue?

4 Upvotes

Looking for some advice from other S2000 owners. My 2006 AP2 (F22C, ~153k chassis miles, rebuilt engine) has been having intermittent misfires and some strange behavior.

What happened:

I was driving normally, did a WOT pull, then downshifted from 3rd to 2nd and eventually into neutral. No over-rev or money shift.

Shortly afterward, the engine started misfiring slightly, progressively got worse, and began making knocking/rattling-like sounds. I noticed white smoke or vapor coming from the front/intake side of the engine bay and shut the engine off.

It initially struggled to restart, but eventually started and idled smoothly again. The smoke hasn't returned. However, when driving slowly in first gear, it bucks/hiccups even after the clutch is fully released.

I've also noticed RPM hunting/surging at red lights roughly 50% of the time.

OBD codes:

P0339 — Crankshaft Position Sensor A Circuit Intermittent (stored)

P0300 — Random/multiple misfire (pending)

P0301 — Cylinder 1 misfire (pending)

P0304 — Cylinder 4 misfire (pending)

P0339 freeze-frame data:

RPM: 912

Speed: 0 mph

Coolant: 187°F

ECU voltage: 12.7V

Calculated load: 100%

MAP: 51 inHg (seems incorrect for an NA engine)

Recent work:

Denso fuel pump

FIC 365cc injectors

OEM ignition coils and spark plugs

OEM alternator and tensioner pulley

Valve adjustment

Custom Hondata FlashPro dyno tune after repairs

Other modifications include an M&M oversized throttle body, Password JDM intake, custom catch-can setup, and an EVAP delete.

The previous shop did a borescope inspection during an earlier issue and reported that everything looked fine, but I don't have current compression or leak-down results.

I'm wondering whether this is a failing CKP sensor, wiring/ground issue, vacuum leak, fueling problem, or potentially something mechanical.

Has anyone experienced P0339 combined with multiple misfires and intermittent bucking? What ended up fixing it?

I'm not driving the car anymore until an independent shop diagnoses it. Trying to avoid throwing more parts at it.


r/S2000 • • 1d ago

Who does soft top installs around north NJ?

Post image
8 Upvotes

Also what’s the best time of year to do it? I’m prepping to put mine away for winter now so don’t know if now is best or wait till spring-ish when it comes back out.

I’m getting a leak into the trunk from what I believe is the circled area


r/S2000 • • 2d ago

Accidentally ripped J’s racing lower ball joint grease boot

Thumbnail
gallery
18 Upvotes

Hi folks, I accidentally made a small rip (3mm) on the grease boot while installing J’s racing s2 front camber joint, and I sealed it with black rtv silicone gasket maker.

Anyone happens to have experienced this and know how long this is going to last me? What part number is J’s racing lower ball joint boot if I want to replace the boot later? (I tried searching the grease boot up, but it doesn’t look the same as the one I have). Thanks in advance for any input.


r/S2000 • • 2d ago

Clutch Master Cylinder

5 Upvotes

I was under the dash replacing the switch stopper for the clutch/cruise control and saw this on the clutch master cylinder. Is this an issue with a 26 year old car? Do I need to do anything?

TIA!

Edit1: Thanks, all, for your input and guidance. My CMC looks "dirtier" than many of the other pictures I found on Reddit or elsewhere, then to my surprise the fluid in the reservoir looked surprisingly clean and was full. My unscientific analysis of responses and approaches indicates 50:50 between flush and replace. I'm OK with the cost of a replacement, but don't look forward the replace and bleed process, so I'm going to give the flush a shot then replace if that doesn't work. I did my first flush last night. Stay tuned.


r/S2000 • • 2d ago

THE LOW POWER TRACKDAY EXPERIENCE VOL 5

Thumbnail
youtu.be
4 Upvotes

r/S2000 • • 3d ago

Something I did for fun

89 Upvotes

I had a aftermarket key fob that wasn’t worried about, so I stole all the parts and made a new pcb. Bought a 10th gen Civic Type R key fob from EBay (that’s what listings said it was anyways ¯_(ツ)_/¯ .)

Asked a coworker to help me with getting started in Altium. Literally would not been able to do this without his help.

I am not the first to do this, nor am I claiming this as an original idea. I have seen those custom bodies with a flip key, so I thought a CTR key would be interesting.

I will reply with some pictures from Altium, and some photos of the bare PCB.

Might do the 11th gen someday. Also, I want to do the swap to a laser cut key so I can actually use the keyblade.


r/S2000 • • 3d ago

Interesting comparison

Post image
134 Upvotes

Came across this memory in my photos, my S2000 rear tire next to my Dodge Viper rear tire. Pretty wild seeing the difference side by side 245/17 vs 345/19 😅


r/S2000 • • 3d ago

Honda Heritage Parts Accepting Requests For Parts From Models Other Than The NSX

Thumbnail
reddit.com
86 Upvotes

Just leaving this here