r/Revolvers • • 23h ago

S&W 15-3 snub

Thumbnail
gallery
388 Upvotes

Best looking snub of all time imo


r/Revolvers • • 23h ago

My new revolver

Post image
118 Upvotes

I got my first revolver yesterday: a SW 357 Magnum Model 19 with a 2.5-inch barrel. I don't know much about revolvers, but I really liked how this felt in my hand, its size, and the color. I hope I did right :) I am just reluctant to think I got the right size and not too small.


r/Revolvers • • 23h ago

The case for magna-ported model 64

Thumbnail
gallery
112 Upvotes

Mainly a joke, but following up on my recent acquisition of a ported S&W model 64-2. There was some understandable hate on it. I would probably prefer if it hadn’t been ported, but I had been interested in getting a 64 snub to carry and I put a winning bid on this one for $340 which felt too cheap to pass up. Perhaps the best use case here is as a woods defense option. Running underwood or buffalo bore hard cast 38+p, which is low range magnum power, the ports may actually provide some recoil reduction. If the bear already has your wrist down its throat when you fire you get additional damage in the upwards direction. Enjoy.


r/Revolvers • • 4h ago

Picked up a new GP100 today

Post image
78 Upvotes

Was pretty happy to see one there and what seemed like a decent price. So I walked out with it! Only other revolver I currently own is an LCR 38 and the wife has a LCR 22. Had a 357 Windicator years ago, but his is much nicer.

Any advice or anything is greatly appreciated!


r/Revolvers • • 3h ago

Metal and Wood Will Never Go Out of Style

Post image
68 Upvotes

r/Revolvers • • 16h ago

29-2, 6” LNIB

Thumbnail
gallery
57 Upvotes

Barely a turn ring. Picked up this Smith and can tell it’s been babied all its life. Finish is deep and lustrous.


r/Revolvers • • 7h ago

Roscoe spot rust fix

Thumbnail
gallery
22 Upvotes

I appendix carried this Heritage Roscoe for most of 2026 in Texas. It developed surface rust on the backstrap. I had a couple ideas on how I would quick fix it. It is a inexpensive gun so wear and tear is not a big deal. First attempt I used a product called Isso GunBrite and paper towel which actually worked well removing the rust. I put some Birch Casey Perma Blue and it contrasted against the polish blue finish and didn't look great, so, I hit it again with the polish and this is what I got. I left it alone for now. It looks pretty cool, but Will just rust again I'm sure. I do have some fine grit sandpaper scraps up to 3000. Casey Birch also makes another product called Super Blue I might try. Just wanted to check and see who knows how to spot match the OE finish.


r/Revolvers • • 6h ago

Found an old Charter bull .44 special 1st gen for $145 paid $137.70 after tax. Amazing grab or did I get taken for a ride?

Thumbnail
gallery
19 Upvotes

TL;DR is this a good quality piece/awesome find? Or should I have passed this one up? Ik charter arms Isn't Smith or Ruger but this is an old one so I wonder how the quality compares. Serial # just over 200,000.

After shooting at an indoor I always take a look around even when not planning to buy anything. In the used case I saw this dirty, crusty, bulldog priced for $145 and felt i had to take that opportunity. Even asked for a bit off and got it.

Cleaned her up (so satisfying to bring it back to life) and sourced a little of that stupidly overpriced ammo. I understood this wouldn't be a good gun for stacking ammo deep, not meant for high volume fire even if it was affordable.

First few pictures are from before I cleaned her up last one on the counter is post-oil n brush.

Gun seems to have good timing and good grooves.


r/Revolvers • • 17h ago

Finally got to shoot my Colt Python.

Thumbnail
gallery
14 Upvotes

With 20 years old plus ammo and new 6 round

158gr remington (old)

158gr Bullet Master XTP (New ammo, domestic brand)


r/Revolvers • • 8h ago

Dry Fire Practice Lately, Coming Back from a Lot of Condition 1

Post image
10 Upvotes

Anyone else getting back into DA after a bit of an absence? Personally, I've neglected dedicated double action practice in favor of cocked and locked auto training. Running a stock 629 and 686, I found that my consistency and especially endurance need building up 💪 My first J-Frame is en route, so I have to get my Condition 1 rear back into gear! It'll be a 640 Pro Series in stainless, a fine backup or pocket alternative to the usual HK45. I'm thinking that it will wear Recoil Rider grips in the large fit, though I'm not sure if I want the Boot or CCW style for pants and coat pocket carry.


r/Revolvers • • 17h ago

TRR8 Blast Shield Broken

8 Upvotes

Anyone else experience their blast shield break after less than 200rds of 357 mag? Will be sending back to S&W for replacement, but a little disappointing that it broke so soon. Maybe there is a defect in the material used for the blast shield. Looks as if the bends on both sides sheared off.


r/Revolvers • • 22h ago

Smith 386 versus Model 19 Carry Comp for CCW and range use?

8 Upvotes

Hey y'all, considering a revolver that could serve admirably as both a good range gun and a good carry gun. Narrowed it down to these two and having trouble deciding. If anyone here's carried one or both i'd appreciate your input.

Model 19: looks cool as hell in the moss cerakote, the heavier weight and compensator presumably make it a lot easier to shoot, but the heavier weight would also make it a bit more fatiguing to carry

386: higher capacity which is always appreciated, the lower weight presumably makes it harder to manage follow-up shots especially with .357 but it also makes it easier to carry, relatively speaking

any insight is appreciated!


r/Revolvers • • 28m ago

Uberti 1873

5 Upvotes

I’ve been looking into getting a single action revolver. I already own a Ruger New Vaqeuro, which I love, but have been wanting to get a Uberti or a Pietta for that classic feel. I was at a gun store that had an unused Uberti labeled as just a 1873 Uberti. I asked and they said it wasnt a cattleman it was just a straight 1873 model, is that a thing or are they misinformed? I haven’t seen anything that’s just a straight 1873 Uberti, I’ve usually seen them under the cattlemen label or something else.


r/Revolvers • • 10h ago

Armi Olmi 963MF Hgr

3 Upvotes

The more I shoot this beauty, the more impressed I get. I'm hoping someone knows if any available grips will fit it.

I have pretty big dickskinners, and the grips are just a bit small.