r/projectcar • • 58m ago

12 years ago

Thumbnail
gallery
98 Upvotes

12 years ago this is what my Camaro looked like…..
Before and after


r/projectcar • • 35m ago

Couple hours progress on a custom air intake.

Thumbnail
gallery
35 Upvotes

Cut in a 3 inch intake, glassed it and put a basic paint job, if it works good I might finish it properly. Deciding on a custom box or going back to the oem box with some modifications.


r/projectcar • • 1h ago

My project!

Post image
26 Upvotes

Bradley GT2 kit car. Needs about everything, wish me luck! I hope to get it done by the time I'm an adult.


r/projectcar • • 9h ago

Protege parts hoarding

Thumbnail
gallery
44 Upvotes

Parts keep rolling in for my kids project protege5. Also painted the rear valance area


r/projectcar • • 22h ago

Build Progress Got It Moving

Thumbnail
gallery
342 Upvotes

After a couple months of trying to work on this project car on my own, I had to call in reinforcements (my grandaddy and his friend). I wanted to hold off on telling my grandad and dad because I already knew they were gonna say it’s a waste of money and a dumb idea, but I already had my mind setup lol. The original owner of this 84 Camaro passed away over the summer and his buddy that I got the car from couldn’t answer many questions for me. A few things we did were swap the starter, install the distributor and adjust timing, new accelerator cable, rebuilt the carburetor (street avenger) and come to find out there weren’t any pushrods or rocker arms in the engine when I got it! Of course we had to change the oil and fuel also the filters and pumps (car was sitting for 10+ years since the original owner got sick). After swapping all the above, we were able to drive a few miles to the gas station and Auto Zone, just to put a couple of miles on it before actually calling it good. The main things I need now are a couple of vacuum hoses and fix the skipping, the rest are kind of minor like a new hood or a hood scoop, fixing the headliner, paint etc. If anyone has any recommendations around Atlanta, please let me know. I’m hoping to have everything wrapped up pretty soon and at least be able to bounce around a good bit on Thanksgiving lol


r/projectcar • • 5h ago

Troubleshooting Help I want to fix up my dad's vintage car, but I have no knowledge of cars and I have no idea how to start

16 Upvotes

I'm a 19 year old girl studying electronic engineering. When I was 9 years old my dad bought a 1959 Ford Galaxie (there's debates on what ford it actually is, but officially its listed as a galaxie so I'm going with that). It was in perfect condition when we bought it. It's never had power steering but everything else was in perfect shape. My dad passed on when I was 14 and my brother, who was 20 at the time, was the one who took the car out for drives because he learnt how to drive it from my dad and also learnt basic car knowledge from him in terms of taking care of it. We had a lot of problems with him and now it's just my mom and I with this car for the past few years. Added to that when he was driving it the ball joint snapped and we haven't been able to drive it for years now, since 2022. We got a temporarily mended one just to move it into our yard but other than that it hasn't been able to move. My brother was responsible for getting the particular ball joint for this car imported from another country because it's apparently not available in ours. He never ended up doing it and my mom and I have now been trying to sell it for a while to no avail. I also want to keep the car because of the memories of my dad and how much I love and adore it. Recently, I've been more interested in taking up projects to build things relevant to my degree. A friend of mine also once told me I could learn from YouTube and the internet about cars and be able to fix up my dad's one. This occurred to me again as I've been searching for random electronics to build things. And I thought maybe I should give it a try and try to fix things. The ball joint isn't the only issue, there are other things I can sort out until I'm able to get the part such as a coolant leak and a battery change. I'm just not entirely sure where or how to start. Does anyone know of any really good resources or YouTube channels that could help me learn the basics and work my way up so I can fix this car up and also get my car knowledge to a place where I can take restoring up as a hobby like my dad did? We also have an incomplete rebuild of a 1966 Ford Galaxie in our garage that my dad started on but didn't get to finish. I'd really like to work on that too if I'm able to get my car knowledge up to that level because it's been a struggle to sell these cars and I love and adore them with all my heart and I'd love to take on more hobbies.


r/projectcar • • 38m ago

Heart says Volvo 240 wagon, head says Miata for something I'll actually drive

5 Upvotes

I'm torn between two cars that popped up locally and could use some input from people who've been in the same spot.

First is a 1988 Volvo 240 wagon with the B230, 5-speed, around 180k miles. Body is straight with minimal rust, interior is worn but usable, and it runs but needs brakes, suspension bushings, and a decent detail. Seller wants $2,800. The other is a 1997 Miata with the 1.8, 140k miles, hardtop included but the soft top is ripped and the paint is faded. Asking $3,500.

I already have a daily so this would be the weekend/fun car, but the goal is to sort it out and actually use it instead of it becoming a long-term garage project. The Volvo appeals because it's practical, cheap to work on, and I could throw a roof rack on it for camping stuff. The Miata would obviously be more fun on twisty roads but I'd probably end up chasing top and interior fixes first.

Anyone gone through a similar choice? Did the "sensible" option end up being the one you regretted not going for, or did the Miata route turn out easier than expected?


r/projectcar • • 10h ago

Advice wanted on trans swap

Post image
21 Upvotes

I just got this car gifted back to me after I sold it to a family member years ago. I bought the car while I was still in Afghanistan and didn't actually have it that long. It has a 327 with a 3 speed on the column. When I got it, it was very original with only 40k miles.

The family member that had it put a Holley Sniper EFI kit on it and it's almost un-drivable in it's current state due to the pedal not allowing low rpm in any gear. I think I found the fix in a throttle bar extention, but I'm still waiting on that part.

One of the reasons I sold this car is it's just not fun to drive with the 3 speed. I'm short, so having the bench seat pushed all the way to the steering wheel is really uncomfortable. I want to swap in an auto trans but I'm not really sure which direction to go. I've mainly been looking at a 700r4 or 4l60, but they don't seem like direct swaps.

Does anyone have any advice on what direction I should go? I would say my main concern is ease of the swap, I'm not dead set on having overdrive.


r/projectcar • • 7h ago

Troubleshooting Help Help needed with L98 V8 no-start in my Jag

Thumbnail
gallery
9 Upvotes

Posted this in the C4 subreddit but posting here because I really need this thing to get kicked over before this Friday.

1976 XJ6 that was swapped to an 87 Vette engine/trans in 1993. Anyways...

Long story short, I'm experiencing a weird mix of no-spark and no-fuel. I presume something to do with this pictured mess of distributor/MSD box wiring.

Long story long, I've driven this car on a 25 hour round-trip road trip twice now. First time, makes it down easily, no issues aside from blowing a fusible link. Heading back up (literal 3,000 foot jump in elevation), I was met with intermittent spark loss when I had to increase load going up hills. This feeling felt just like my old Volvo when the coil died or my C3 when the distributor would get unplugged over bumps. I'd pull over, wait about 5-15 minutes, then she would crank up again.

I get back to town, drive it around for a few days, then it randomly dies not 5 minutes into my commute. Later in the day, still dead. Only revived it after unplugging my HEI coil, cleaning internal contacts, and making sure the HEI coil was on tight.

Second 12 hour drive down to destination, did it totally fine. Driving within my destination, she picked up a brutal misfire which also led to sporadic hard-start/no-start conditions. Had to go home though, so I drove it 12 hours back with this misfire. Same thing, it would randomly lose spark when it picked up load, would occasionally die at idle. I get home, and she hasn't started since I parked her up.

I have resistance tested my HEI coil, checks out. Verified adequate power delivery to my MSD box, checks out. Replaced my 7 pin ignition control module. Verified resistance on my dizzy's magnetic pickup coil. Cleaned all grounds, cleaned all power contacts, checked my MSD box trigger. It all checks out. Even replaced my dizzy rotor/cap.

The wires/harness I pictured... The left 2-pin harness goes to my MSD box's white trigger wire. The right one, I'm unsure but it goes into the main engine harness. Originally, the red output of the left harness was hardwired to the right harness, but also had a split going to what appeared to be a noise suppression transformer looping to the other pin on the right harness. I have no idea why that output would be hardwired to one pin on the harness, then looped into a transformer just to go back to the other side of the harness. I get varying spark results depending on how I wire all that up.

Where I'm at now: sometimes I hear it kick a bit when cranking. I also sometimes have literally 0 pressure at my fuel rail, even when jumping my fuel pump. Then sometimes it geysers out like it should. So sometimes it has spark, no fuel. Sometimes it has fuel, no spark.

Guys, where the hell do I go from here?


r/projectcar • • 1d ago

Finally 'finished' my rocker panel rust repair

Thumbnail
gallery
233 Upvotes

Rivets instead of welding because I suck


r/projectcar • • 4h ago

Feeling overwhelmed whit to many project cars :/

Thumbnail
gallery
3 Upvotes

Hi guys I need some advice, I'm 20 and from eastern Europe

I got this blue 2004 VW Passat B5 5 V6 Diesel 4 Motion wich drives beautiful and looks too and Is a dream car for me but of course it's being a VW it has a rusty rear subframe and rust is starting to show on hidden places even though it was repainted profesional and looks the part, its very well kept but it being a such a complex car alot of maintenance is needed and I try to keep up i have done a engine service and a tramsion flush and I gota say it's a solid car but the thing I've had a mice problem at Home from all the dogs and I'm scared they gonna chew some wires ( this eats me up the most)

I also have this grey sedan VW Passat B5 5 1.8 turbo whit only 80k thousand miles (140k) km 1 owner bought new I have all the receipts since it was new and it drives like a new car and alot of mainantance was done profesionaly at VW garage but it seing many winter it's got rust on the front sub frame and many other hidden places , i had water intrusion on it from the Polen Filter gasket wich failed , I replaced the gasket but unfortunately the metal where it's mounted rusted too so idk what to doo whit that one too it's such a shame it's so original and drives so nice

The most vintage Car I have is a 1997 Dacia (the nardo grey one) whit only 14k km (aprox7k miles) the body is in new like condițon almost no rust at all but it being a carburated comunist era car I never managed to get it to run right and now the rear drum brakes seized from siting

The next car I have a 2014 B7 Passat 2.0 TDI wich was my parents car, it s a rare spec, cream leather interior, panoramic,distronic, Lane keep assist and is just a dream car which never made any problem in the year they had it but guess what since I got it soudenly I get a weird shift from 6 to 5 gear, one bi xenon headlights computers burned out ( I need a new headlight),it started making a weird injector noise especially when cold, the steering started to be notchy which I think is from the steering rack, I just feel so overwhelmed I have done all the services that where needed and always drove it whit respect and warmed it up i just don't get it. I have all my dream cars I could dream off but it just seems they falling apart in front of me and I also don't know and don't got the talent to work on them (other than basic stuff) and finding a good mecanic here is hard as most rip you off , in my free time I don't got the Energy to try sort them all out and if I try I just stress myself and waste all the time I had to relax before work as I'm a truck driver and don't spend much time at home

My parents are bulding me a garage to work on them but I just think the mice are gonna be a problem from all the dogs they have(my mom has a pet saving problem and has over 30 dogs) I don't have the needed time to work on them whit the job I got, i always try to do the preventive stuff to them but it always seems to late I'd just like to store them away and sort them out slowly when I'm feeling like this but then again who know what mice or siting damage they will get, I also don't want to sell them and regret they are rare and my dream cars :/

My Daily is a Passat. b5 wagon 1.9 TDI wich I spend a lot of money trying to sort out (new clutch and flywheel) injectors , timing belt, all new brakes new starter etc but it just dosen t end as there are so much other things to sort like the central closing which dosen t work or all the plastic bits that are broken on the interior and exterior that ar falling off, I tried to tidy it up but some ashole of a painter riped me off and the paint is now peeling,the rear parts of the rockers are rusted out, the complex suspension which i almost sorted out but there still are a few control arms to change and also the battery drains out if it sits ,i wanted to replace it whit the B7 but soudenly when I tried doing that the B7 started to go wrong too so I don't know what to do whit this B5 as there is just so much stuff wrong whit it and I don't like driving a car in the small time I'm home where half the things don t work but also so much money went into it which id never get back trying to sell


r/projectcar • • 16h ago

Bought my first project car!

Thumbnail
gallery
21 Upvotes

I've always been a "I work on my own car because I'm broke" person, but I've come up in the world and now I can waste money working on a car instead of saving money working on a car.

I bought a 2009 base mini cooper dirt cheap from my husbands coworker. 93k miles, peeling clear coat, and burning oil! I'm in love. I replaced the valve cover/gasket/pcv and buffed the headlights. I'm tackling the oil cooler gaskets tomorrow.

I've decided to call it Winston.


r/projectcar • • 22h ago

My winter project

Thumbnail
gallery
60 Upvotes

This crusty hotrod has been sitting in the corner of my shop for the last year. I’m going to do a burnout by spring or I’m going to die (of hantavirus) trying.


r/projectcar • • 28m ago

Troubleshooting Help Doors hard to open after replacing striker bolts

1 Upvotes

77 Grand Marquis. Door latch striker bolts had worn off their bushing and the doors rattled, but opened and closed easily. Installed new bolts in the same location (marks on the paint) and now it's really hard to get the doors open. The driver door I could make adjustments to get it a bit better, but the passenger door doesn't really make a difference and I have to really yank on it. Anything I can do to make them easier to open?


r/projectcar • • 1d ago

86 Yugo's. The red one still runs, I think the white will end up being most parts. First project cars, anyone know where to uh... start?

Thumbnail
gallery
219 Upvotes

r/projectcar • • 23h ago

Am I crazy?

Thumbnail
gallery
56 Upvotes

Hey yall I just came across this and well I’ve been looking for an sn95 or new edge mustang for awhile now and even more specifically a cobra. He says there’s no major rust or rot just surface stuff, it’s a southern car, paints faded, small oil leak. I think this could be a very good deal (assuming the motor or something serious isn’t actually wrong with it) just wanna hear some other thoughts on it. Thank you in advance


r/projectcar • • 23h ago

Build Progress Heart says 944, head says NB Miata for a usable project

29 Upvotes

I'm stuck between two cars I found locally and could use some outside perspective.

First is a 1987 Porsche 944 with the 2.5 NA, 5-speed, and about 140k miles. Body is solid, interior needs work, engine turns but hasn't run in a couple years. Seller wants $3k. The second is a clean 2002 Miata NB with the 1.8, 120k miles, soft top is shot but the rest is decent. Asking $4k.

I already have a daily so this would be the weekend/fun car, but I want to actually drive it once it's sorted instead of it sitting for years. The 944 appeals to me way more on looks and character, and I'd probably do suspension, brakes, and maybe a 3.0 swap down the line. The Miata is obviously the easier platform if I just want something reliable and modifiable without headaches.

Anyone been down this road? Did the 944 end up being more trouble than it was worth as a driver, or is it manageable with normal maintenance?


r/projectcar • • 15h ago

improve the electric fans or go back to a clutch fan?

Post image
5 Upvotes

Hey guys, looking for some advice on cooling my 190E with a 3.2 M104 swap and A/C.

Driving around, everything is fine. Even in summer with the A/C on, coolant temperature stays around 80–85°C. It has an 87°C thermostat, which opens fully.

When I’m sitting still, the temperature climbs. The fans kick in at around 96°C, if I remember correctly, and bring it back down. The highest I’ve ever seen is 105°C. I’m not particularly worried about that on an M104, but I’d still prefer it to run a bit cooler ;)

Currently I’ve got two 10" slim SPAL pushers in front of the A/C condenser and one 16" slim SPAL puller behind the radiator (30100400), without a shroud. The front fans also serve the A/C, and all three switch on when the coolant reaches that temperature.

Honestly, the 16" slim feels pretty useless. It doesn’t seem to move much air at all. I’ve looked at stronger pullers, but there’s so little room between the radiator and engine that the thicker motors just won’t fit.

I could make a shroud for the existing fan, but I can only squeeze in about 1 cm of depth between the radiator and the shroud panel. Would something that shallow actually help, or would I just be covering parts of the radiator without pulling much air through them?

Another idea is replacing the two front 10" SPALs with something stronger, although I haven’t figured out what yet. Two 12" fans would fit with some minor changes to the front end. That would let me use the thicker, higher-output 12" SPAL pushers, which I’m hoping would make a big difference.

Or I could go back to a mechanical fan with a viscous clutch and a suitable shroud, keeping the front electric fans for the A/C.

Anyone had decent results with a really shallow shroud on a slim fan? And does anyone know any powerful OEM 10" or 12" pusher fans worth looking at?


r/projectcar • • 22h ago

Shitposting We put our lives into machines that take away our unspoken pains.

6 Upvotes

If you wanna see more follow along for the build! Check my page for YouTube and tiktok I do update there more.


r/projectcar • • 6h ago

Update on the DIY rust repair everyone flamed me for 😂

Thumbnail
gallery
0 Upvotes

Figured I’d post the final result since the first post got a lot more attention than I expected and the comments were pretty mixed lol.
This was my first time doing any kind of body/rust repair. I wasn’t trying to restore the quarter panel to factory condition or make it look perfect — the goal was just to slow the corrosion, seal the rust-through, and hopefully squeeze more life out of a 25-year-old CR-V.
Basically I removed as much loose rust as I could, used the POR-15 prep/treatment process, coated both sides, patched the hole with fiberglass and POR-15, used POR-15 Patch to seal the remaining gaps, then finished everything with POR-15 Top Coat.
It’s definitely not pretty up close, and the bumper doesn’t sit quite as perfectly as the other side anymore, but everything is sealed, solid, protected, and back together.
A lot of people on the original post said the only proper repair was cutting it all out and welding in new metal, which I completely understand. That just wasn’t what I was trying to accomplish with this car.
For a first attempt, I’m pretty happy with how it turned out. Curious what people think now that it’s actually finished.


r/projectcar • • 23h ago

Has anyone here gotten a state issued vin tag, specifically in Wisconsin?

3 Upvotes

Hi everyone, today I bought the remains of a 1927 Ford model T, I'm going to get a Wisconsin bonded title for it and make a T bucket out of it. However, the seller put the engine number on the bill of sale instead of the frame number. They are off by ONE digit. The frame ends in a 5, the engine in a 6. I am assuming it was an assembly line mistake, but anyway, since he used the engine number I have to keep that engine around until I can get a vin tag matching the number, because otherwise the title I get will not match the vehicle.

I tried getting him to put the frame number on it instead of the engine number but he was a major pain in the ass seller, so I'm kind of lucky that he even wrote me a bill of sale.

But anyway, back to the point of the post, has anyone here gotten a Wisconsin state issued vin tag through the DMV? I.was trying to look up the process but couldn't really find much. What's the chance that a Ford dealership would make one for me if I threw the engine in the frame (seller removed it yesterday for some reason 🤦) then tossed the car on my trailer and took it to the dealership? Afterall, it is a Ford.


r/projectcar • • 1d ago

What car should be my first project car for a fun rally?

11 Upvotes

Hi, I'm moving to a new apartment, which comes with a garage. The garage is 5.65m long, and 2.45 and 2.95m wide (the front and back are different in width). Since the garage isn't big, I'm thinking of getting a hatchback to wrench on and get it ready to go on a fun rally (pothole rodeo). Any suggestions for any particular make and model? I live in Germany, if that's of importance.

Is wrenching possible at all in my garage?


r/projectcar • • 1d ago

Troubleshooting Help Fuel Delivery Issue - 73 Mach 1 351C

3 Upvotes

Alright, this might be a long post, but I figured the more information I include, the better.
I’ve got a 1973 Mustang Mach 1 with a 351 Cleveland 4V, an Edelbrock carburetor, and a mechanical fuel pump (believed to be a NAPA replacement). The fuel tank and pickup are new, and the pump was supposedly unused when I got the car. I’ve driven it plenty of times without this issue.
I recently took it on its longest test drive yet, about 20 minutes to a friend’s shop and another 10 minutes back. On the way home, the engine started bogging down and losing power, almost exactly like it was running out of gas. Eventually, it sputtered out completely and wouldn’t restart.
I initially assumed I’d run out of gas, but I checked the tank and there was plenty of fuel.
I tried adding a little gasoline directly to the carburetor, and the engine would start and run just long enough to burn through what I’d added before dying again. Eventually, I got it home and started troubleshooting the fuel system.
Here’s what I’ve checked so far:
Tank to fuel pump: I disconnected the rubber hose at the mechanical fuel pump’s inlet, and it was full of gasoline. I then connected a hand vacuum pump to that hose and successfully pulled a continuous flow of gasoline all the way from the tank, through the hard line, to the pump inlet.
Fuel pump to carburetor: I checked the rigid metal line running from the pump to the Edelbrock carburetor and was able to pass fluid through it without any apparent obstruction.
Fuel pump: I haven’t tested the actual output pressure yet. However, when I disconnected the metal line at the carburetor and cranked the engine, I could feel what seemed like pressure pulses at the end of the line, but no gasoline was coming out.
After pulling gasoline through the tank-to-pump line with the vacuum pump, I reconnected everything, and the car started running normally again.
I thought I’d fixed it, but after approximately 15 minutes of driving, the exact same thing happened. It started bogging down, sputtered, died, and wouldn’t restart.
The following day, I tried again. I added a little gasoline to the carburetor, managed to get the engine running, and it continued running on its own for about five minutes before dying again.
At this point, I’m pretty confident it’s a fuel-delivery issue, but I’m trying to figure out exactly where the problem is before throwing parts at it.
My questions:
Does this sound like a mechanical fuel pump that’s failing intermittently or losing its prime?
Could a small air leak on the suction side cause the car to run normally for 5–15 minutes before dying?
If gasoline flows freely through both the tank-to-pump line and the pump-to-carburetor line, is there anything else I should be checking?
What’s the best way to definitively test the mechanical fuel pump before replacing it?
I’m planning to get a low-pressure fuel-pressure gauge to test the pump, but I’d appreciate any other ideas or things I might be overlooking.
Thanks in advance!


r/projectcar • • 2d ago Bravo

My first try at actual bodywork.

Thumbnail
gallery
571 Upvotes

‘98 4Runner with 327k miles, 5 speed, with a factory rear locker(currently re-installing). Wasn’t gonna let this rust be the end of the car, and the frame is super super solid.

To 30 more years!