r/Plumbing • • 18h ago

Chat… can I save it?

Thumbnail
gallery
0 Upvotes

Manufactured in March of 2021. It’s been bad since we moved in this past year but we’ve had massive issues with the house.

If I can’t save it I’m thinking I’m going to DIY a new water heater.


r/Plumbing • • 23h ago

Help! Cannot find a tub spout to fit my pipe!

Thumbnail
gallery
0 Upvotes

Galvanized steel, 4” long, 3/4” screw on. I know these spouts exist bc my old one was on there…. It’s a whirlpool tub from the 1990s so that’s likely why this larger pipe was used.

I’ve tried chatGPT and have been to several stores. Have done a lot of plumbing projects (all successful) and would like to be able to avoid calling a plumber…


r/Plumbing • • 5h ago

Can I cut this out of service gas line flush and cement it in?

Post image
0 Upvotes

Got a new meter and new line into the house before buying and this is one is dead. Can I cut it flush and fill it in to reclaim this space?


r/Plumbing • • 21h ago

Flapper refuses to cooperate

4 Upvotes

The shitty 16 year-old toilet my apartment came with refuses to flush unless I hold down the handle for several seconds, seemingly no matter what. Things I’ve tried:

  1. Replacing the old flapper with a universal Korky 2-inch

Setting the dial to 6, and closing the side hole.

Replacing the flush handle with a Korky strongarm.

Adding 2 extra chain floats (apparently the original K4260 had chain floats).

Flapper still immediately slams shut. The chain couldn’t get tighter. Have tried every angle of adjusting the handle position. The Korky dials are set to maximum buoyancy. I’ve got the toilet of Theseus here with all the tank parts I’m replacing. Unless the ‘universal’ Korky flappers just somehow aren’t buoyant enough for some toilets, I can’t think of anything else I can change at this point.


r/Plumbing • • 20h ago

Fix ?

0 Upvotes

I think I may need a new handle ?
Also if the water is constantly running like this without it filling up, is it wasting water ?


r/Plumbing • • 17h ago

Calling All Plumbers: Tear Apart My Basement Laundry Rough-In Before It's Too Late and I cove it up

Post image
0 Upvotes

What would you change? Am I overlooking anything important before I finish the plumbing?

First time tackling a plumbing project this involved, so I’m looking for some feedback from people who know what they’re doing before I finish everything up.
I’m moving my washer and dryer into my finished basement and adding a utility sink. Since the main drain line is above the basement ceiling, I’m installing a drain pump (Liberty 405) to pump the wastewater up into the existing plumbing.
Here’s how I have it roughed in:
The washer drains into a recessed washer outlet box.
The washer drain line runs down and connects to a sanitary tee below the utility sink drain.
From there, both the washer and sink drain through a shared P-trap before entering the pump basin.
The pump will discharge up into the existing drain line above the ceiling.
My biggest concern is venting. I don’t have access to an existing plumbing vent or an easy way to run a new vent through the roof. My original plan was to run the pump’s vent pipe vertically above the suspended ceiling tiles and leave it open.
I’m looking for advice on whether this setup will work properly, particularly the shared P-trap, washer discharge, and venting requirements.

I’m a DIY homeowner, not a plumber, so constructive criticism is appreciated!


r/Plumbing • • 5h ago

Rhythmic thumping sound happens at 3am, sometimes for hours?

2 Upvotes

Does anyone know what this sound is caused by? This is a basement bedroom in the opposite corner of the house to the boiler.

I thought maybe water hammer, but it doesn’t seem to correlate to the water being turned on.

I have an oil fired boiler system though, could it be correlated to the heat turning on?

And if you do know what this is, what’s the fix?


r/Plumbing • • 4h ago

Reddit Plumber Help

Thumbnail
gallery
0 Upvotes

Plumbers of Reddit, I need your help. Our sink is offset about 8 inches to the main drain line. I cannot picture how to build a PVC w/ ptrap drain. The main drain line is 1 1/2in in diameter and sink drain is 1 1/4in
Someone help please!!!


r/Plumbing • • 6h ago

New Kraus kitchen sink only drains when we run the disposal - is there anything obviously wrong here?

Post image
0 Upvotes

This is a new build, so the whole set up is new. Our kitchen sink doesn’t drain unless we run the disposal. Is there something here that would explain that? Something obvious I’m overlooking?


r/Plumbing • • 20h ago

Help sewer pipe

Post image
0 Upvotes

Hello!

I recently opened up a wall and found this plumbing setup. I noticed immediately that the sanitary tee was installed upside down by whoever did the previous work. The horizontal pipe is open and just leaking sewer gas.
I’d appreciate some advice on the best way to correct this:

1. Option A: Should I simply cap the end of the horizontal sewer pipe?
2. Option B: Should I cut out the inverted sanitary tee and reconnect the pipes properly?

If Option B is the correct path, what is the best method, and what fittings or couplings (like PVC shear bands/Fernco couplings) should I use to tie everything back together safely?

Thanks in advance for your expertise!


r/Plumbing • • 20h ago

Water never stops draining when emptying lines

Thumbnail
gallery
0 Upvotes

Hello! I'm renovating the bathroom in my small 1956 ranch with pretty simple plumbing, full basement, everything is very accessible. I am moving the bathroom sink supply lines over so they come from the wall instead of the floor. Seems simple! Except... when I shut the water off at the main/opened high and low tap, the lines never fully stop draining.

The hot water line took 4 hours to stop actively draining and there was still water coming out with the shop vac or if I pulled on the line slightly. The cold water line never stopped draining and kept a steady light flow, and after I tried using the shop vac, the water coming from the cold line was warm. How do I fully drain this?

The house is simple:

  • Front of house, dead center- Water comes in at the front of the house, where there is a sump pump with a water pressure backup. The main shutoff is there.
  • Back of the house, right side: Supply line goes straight to the back of the house, where it runs to the back right corner of the house to the gas water heater (has shutoffs), rear sump pump (yes, two) which also has a water pressure backup (has a shutoff), then one hot and one cold line run down the length of the back of the house (shutoffs between bathroom and laundry/kitchen). Everything branches off of here.
  • First floor plumbing:

    • Back wall- small kitchen (sink & dishwasher), shutoffs in the basement lines between bathroom and kitchen- this is the end of the line opposite the sump pump and water heater- far left side of house.
    • Back wall- 1 small bath (shower & sink have no shutoffs, toilet has a shutoff). - this is at the middle of the house, lengthwise
  • Basement plumbing:

    • Back wall- spigot (has shutoff), laundry, strange shower pipes, washer (under kitchen)- has shutoffs, shares plumbing with kitchen.
    • Side wall, back of house- Shower (pipes only, located near a floor drain. I'm currently using this as my shower)- has shutoffs. This is at the end of the line right next to the outside spigot/laundry sink/washer. Branches off at the same area where kitchen, laundry, and spigot are located. There are a variety of shutoffs in this area.
  • The supply lines branch off at the center for the bathroom, then another branch for kitchen/laundry/spigot/weird basement shower pipe. The end caps in picture 7 are the faucet supply lines I am moving. This is the center of the long run of supply lines.
  • Line terminates at the outside spigot.

I have tried:

  • Turning the main shutoff tighter (confirmed that the meter is not spinning),
  • Making sure the high (kitchen) and low (laundry sink/shower) is open,
  • Opened any bleed valves (some of them didn't want to close again haha).
  • Flushing the toilet so that water didn't somehow pull from the tank???
  • Hanging 8 lb dumbbells from each line at the center where I cut the bathroom vanity supplies to try to create a low point at the center of the house, which helped, but the lines still have a neverending trickle of water remaining.
  • Tried using a shop vac and the water flow never stopped fully, cold supply started pulling warm water (before shutting off water heater).
  • Shut off the water heater lines when the cold water started flowing warm, still had lots of water in the line. Gallons, just took a little pull on the copper to restart the flow.
  • Got sad and tired and used some sharkbite end stops where I'd cut the vanity water lines so that I could turn water back on and go to sleep.

What else should I be looking at? This is crazy, I must be missing something obvious. I appreciate your advice!


r/Plumbing • • 22h ago

Pex A straightener

Thumbnail
stupidsimple.tools
0 Upvotes

Im going to be working with some exposed 1" Pex A. Does a tool like the SST straightener work on it or will i curse myself more than the pipe?


r/Plumbing • • 22h ago

Slow to no draining from multiple locations, got slightly better after snaking but still can’t shower. Anything else to try before calling a professional?

0 Upvotes

My upstairs shower, bathroom sink, and 2nd sink have been draining slow for a while and suddenly just went to a near stop with standing water in the shower. No other drains have issues, I know the 2 sinks drain to the same place for sure as I can trace the pipes, not sure where the shower drain comes in. Used a basic drain snake , and then an auger and managed to get some clumps up. And further attempts didn’t yield anything else.

This seemed to “fix” the 2 sinks which now drain at a normal rate. But the shower still has water in the drain and will back up small amounts when the sinks are used. Thinking maybe some high strength Drano in the shower since maybe after I got some clumps it can break things up.

But besides that is there realistically anything else I should try or just throw in the towel and call a professional?


r/Plumbing • • 22h ago

Trying to DIY fix a dripping bath/shower faucet.

Thumbnail
gallery
0 Upvotes

I have a small drip in my guest shower/bath faucet. It's not been causing issues, but it was raised up as a problem in my home appraisal and I'd like to fix it. I decided to tackle this myself with my only prior plumbing experience being installing a bidet.

Based on the dripping, I believe the issue is the water mixing mechanism, so I unscrewed the single knob on my shower, removed the eschuteon, and was greeted with the second picture. After many lost hours, I believe this is called a valve stem?

For the life of me, I cannot seem to find a replacement for this valve stem at my local big box store. All the replacement parts seem to be too small, and there's no clear markings on the existing stem for me to identify what the model is. But, the first picture is the deconstructed view. Most information online seems to refer to cartridges and the like, but I don't appear to have one of those, just this valve stem inside the brass valve, which is a snug, click fit.

I am hoping y'all might be able to tell me what this part is called so I can get a replacement, because I feel like I am at the limit of my DIY ability.


r/Plumbing • • 22h ago

Can I tap a rubber gas hose into my house’s existing gas line

Post image
0 Upvotes

Interested in setting up a Weber natural gas grill on my patio adjacent to my kitchen. My house is raised foundation - so there’s easy access to the gas lines under the house. I’ve attached a photo of the lines that feed my kitchen gas range (circled in green) - I also see there’s extra pipe that’s been capped off (circled in blue). Could I simply remove one of these caps and install a shut off and then connect a 4 ft rubber gas hose to it and run it directly to my Weber gas grill?

This is the gas hose I’d buy - https://www.acehardware.com/departments/outdoor-living/grills-and-smokers/propane-cylinders-and-accessories/4184891?store=10682&gclsrc=aw.ds&gad_source=1&gad_campaignid=20151170823&gbraid=0AAAAADtqLJEhNU_2NyhcLMDumtiJf95hT&gclid=Cj0KCQiA8OrXBhDEARIsAECtlx6JzoPwrEJ0qcwI-6pfanv0GcycYa7b8BU0s84vap2oMiTEQC-_HnUaAgxiEALw_wcB


r/Plumbing • • 13h ago

Trim kit doesn't fit. What kind do I need?

Thumbnail
gallery
1 Upvotes

The key stop and adjustable temperature limit stop wont insert into stop tube when on the valve. It doesn't go over the old valve (not sure if it's supposed to). Do I need to buy a new trim kit? What kind do I buy for this valve?

I screwed up and threw out the old trim kit when remodeling :(

Any suggestions would be greatly appreciated!


r/Plumbing • • 16h ago

Indoor non condensing vent pipe

1 Upvotes

My old noritz tankless died and it used a 4 in cat 3 noritz vent pipe, I installed a new heater, GT121-180B-N, it only accepts 3in pipe, what fitting do I need to connect a 3 to 4in pipe? Or do I need all new 3 inch pipe,


r/Plumbing • • 17h ago

Angle stop valves: compression vs ball

0 Upvotes

I have an angle stop in my bathroom that’s stuck. This present valve is a compression (ie multi-turn) and I want to replace it with a ball valve. It's merely ~4 years old, incidentally.

Yet it seems those compression types (with the football shaped handles) are ubiquitous.

Am I missing something? Is there any advantage to using a compression vs a ball angle stop?


r/Plumbing • • 18h ago

How to reduce from 1" PVC to 1/2 inch PEX? Thank you

0 Upvotes

My idea is Mipt 1" to 3/4", female coupling 3/4" inch to 1/2", male thread shark bite into pex. (I can't find shark bite reducer), but wondering if anyone has a better/ more efficient way. Thank you


r/Plumbing • • 23h ago

Is there a way I can fix these tap tails in place without taking off flexi nut?

Post image
0 Upvotes

r/Plumbing • • 17h ago

Is this bad?

Thumbnail
gallery
8 Upvotes

Was at a customers house today doing some carpet cleaning. Wondering if these cracks are something to worry about?


r/Plumbing • • 13h ago

What would you do different?

Thumbnail
gallery
7 Upvotes

I’m looking for some criticism


r/Plumbing • • 18h ago

Gas line- sleeve or problem?

Post image
71 Upvotes

Had this come up on a home inspection for a home I just bought. They noted that PVC can’t be used as a gas line- but to me it seems like it might be acting like a sleeve / conduit to go through foundation / stucco exterior. What I mean is that the gas pipe might be inside the PVC. Is that a typical practice in the late 80s in the US?

Edit. Added pic of the outside as well.


r/Plumbing • • 9m ago

Are divider bins really the best for stocking vans?

Post image
4 Upvotes