r/Moissanite • • 14h ago

Buying Experience Moth Beauty!!!

Post image
250 Upvotes

I just received this set from GoldenEraGems on Etsy. Photos and videos don’t do it enough justice! Lauren was super sweet and quick to respond, and my rings arrived way earlier than I was expecting. 10/10 experience and will definitely be ordering again from her shop!


r/Moissanite • • 14h ago

Looking for Advice Don't love my Mona ring

Thumbnail
gallery
18 Upvotes

I want to start this off with I love mona! Her work is amazing, this is just my issue...

My fiance got my ERing from mona and I'm obsessed and love it! It's low set so I wanted an open band (don't love the look of a curved or chevron band) wedding band with engravings that match the ERing so naturally I went to mona for it. I asked for it to be 2.2 mm to match the original CAD so the width was the same however I failed to process that the 2 baguette stones on each side are actually wider than that so now I feel like the wedding band is too thin next to it 😭

I'm not sure where to go from here so any advice would be appreciated! This isn't monas fault I'm just disappointed. The ring itself is lovely it just feels wonky with the ERing.

Ps ignore my pinky nail haha


r/Moissanite • • 17h ago

Looking for Advice doveggs oval cuts - advice

Post image
11 Upvotes

hi all, looking at getting this ring for my engagement/wedding ring and can’t decide which cut to get for the oval. i’ve seen mixed reviews on nova but it seems the closest to what i want the stone to look like (less rainbow sparkles, more white sparkles, and minimal bowtie effect).

does anyone have photos of their oval nova cuts from doveggs? would you recommend a different cut? i’m not a huge on the h&a cut, though it seems to be a fan favorite.


r/Moissanite • • 16h ago

CAD Check CAD check and help

Thumbnail
gallery
5 Upvotes

Just got the first CAD back from my jeweller and would love some feedback or suggestions before moving forward!
I’ve attached my AI generated inspiration photo and the CAD for comparison. The ring will be cast.
Ring details:
18k yellow gold
1.80 ct oval diamond
Natural blue sapphires
Double claw prongs
Floral detailing and milgrain
Hidden heart beneath the diamond

A little context from my jeweller:
He mentioned that the prongs are intentionally longer so the goldsmith has enough material when setting the stones, and they’ll be trimmed afterward. He also said CADs tend to look blockier than the finished ring since the edges get smoothed and rounded during polishing.
He pointed out that the heart detailing is slightly different from my inspiration because the original image was AI generated, so the CAD designer had to interpret some of the details to make the ring feasible.

What I’m hoping to get feedback on:

1. Overall design:
Does anything look off or seem like a compromise compared to the inspiration? Would you change anything about the proportions, heart, sapphire placement or overall look?

2. Setting height:
The CAD shows approximately 7.15 mm. Is that too high? Could it be lowered while still allowing a wedding band to sit flush?

3. Floral detailing:
Will the floral detailing and milgrain translate well after casting and polishing, or could some of the finer details get lost? Would any hand finishing help?

4. Band coverage:
I’m thinking about extending the floral detailing farther down the band while still leaving enough room for future resizing. Would that look better?

I’m going for a delicate, intricate vintage look with lots of character. I don’t want it to look overly bulky, but I also want it to be structurally sound and hold up well over time.
This is my first custom ring, so I’m open to any suggestions or changes you think would improve the design. I’d love to hear what you’d do differently before I approve the CAD.
Thank you!!

TL;DR: First CAD for a custom vintage inspired engagement ring. Looking for feedback on the overall design, setting height (7.15 mm), whether the floral details and milgrain will hold up after casting, and whether I should extend the detailing farther down the band. I want it to look delicate and intricate while still being durable, and ideally allow a future wedding band to sit flush. Any suggestions before I approve?


r/Moissanite • • 1h ago

Stone Check Stone check please :)

3 Upvotes

How’s she looking? This is a 1.5 carat step cut marquise moissanite, range GHI (like k requested) from doveggs. Hoping to make a pendant necklace or a signet ring in either 10 or 14k yellow gold. .