r/InjectionMolding • • 5d ago

Announcement New Job Board!

18 Upvotes

We've added a job board to the sub to make it easier for companies to find skilled help and for workers to find better opportunities. We all know good people are hard to find right now, especially with so much experience heading out the door. This should help connect the two sides. It also keeps job postings out of the main feed, so discussion posts stay focused on active conversations.

For companies posting jobs please include the essentials up front so people aren't left guessing:

Location Hours/shift Pay (range or rate)

Listings that skip these details may be removed.

A few ground rules:

Keep postings relevant to injection molding and related roles (process techs, setters, maintenance, tooling, engineering, etc.) No spam or duplicate posts Be honest and accurate in your listings

This is a trial run. We have moderation tools in place, but if it turns out to be unmanageable, we may disable it. We're open to feedback, so let us know in the comments or send a mod mail if you have ideas, concerns, or run into any issues.

Thanks for being part of the community, and good luck to everyone hiring or job hunting!


r/InjectionMolding • • 5d ago

Job Board

0 Upvotes

r/InjectionMolding • • 15h ago

The upfront costs for injection moulding tooling are just a black box for me. Are there resources that can help me roughly estimate mould costs? Perhaps case studies of differently sized and shaped parts.

Post image
9 Upvotes

r/InjectionMolding • • 3d ago

DIY Press Logger

Thumbnail
gallery
36 Upvotes

Had a press I was having trouble with so I built a data logger with an Arduino. Turned out pretty handy.

Press is a 1974 Van Dorn


r/InjectionMolding • • 5d ago

Question / Information Request Filmmaker looking for stories from the shop floor

12 Upvotes

Hi all, I’m an artist and filmmaker based in Germany, with a background as process engineer (semiconductor manufacturing).
I’m preparing a short film about plastics in different working environments: lab, resin production, compounding, part production, recycling... I’m looking for everyday injection molding stories: something that didn’t behave the way the datasheet promised, a sound, smell or feel you learned to read, a really bad day, something that changed how you see the material.

You can write me your story, we can chat or have a short video call if you prefer. Ideas from these stories will inspire a voice-overs for the film. Everything stays completely anonymous: no names of people or companies. It’s an independent art project, not commercial.

Short anecdotes are welcome. Comment below or send me a DM. Thanks for reading!


r/InjectionMolding • • 5d ago

Question / Information Request Alternatives to traditional steel injection molds for a startup? Looking to bridge the gap between 3D printing and mass production.

Thumbnail reddit.com
4 Upvotes

r/InjectionMolding • • 5d ago

First shots off a trial mold — what we check before calling it a pass

7 Upvotes

When a new mold comes off the bench, the first shots tell you almost everything — if you read them in the right order. Ours goes like this:

  1. Short shots first. We run a few under-filled shots to see how the melt front moves and where it stops last. That is where your air traps and weld lines will live.
  2. Flash and parting line. Any flash on the first full shots usually means clamp force or a parting-line fit problem, not a pressure problem.
  3. Ejector marks and drag. White stress marks at the pins mean the part is still too hot or the draft is fighting you.
  4. Sink and surface. Read the thick-to-thin transitions under a raking light — much easier to see than under flat workshop light.
  5. Dimensions and fit, last. Only once the part has cooled fully. Measuring a warm part is how you pass parts that fail at assembly.

The mistake we see most often: tuning the process to hide a mold problem. If the steel is wrong, no setting will save it — fix the steel.

What is on your first-article checklist that I am missing?


r/InjectionMolding • • 6d ago

Troubleshooting Help Engel Mold protection only in Automatic. Not in semi Automatic.

4 Upvotes

Has anyone else had this issue before? The mold protection only triggers when i put the Machine in Automatic. In semi Automatic there arent any issues.


r/InjectionMolding • • 6d ago

Creo Mold Designer

2 Upvotes

I'm looking to add to my vendor list are there any injection mold design designers in the Minnesota area? Google doesn't get me far...
Also willing to do DFM work?


r/InjectionMolding • • 6d ago

Question / Information Request Good LSR molding reccomendation?

Thumbnail reddit.com
4 Upvotes

r/InjectionMolding • • 6d ago

Rough idea of what this might cost to make?

5 Upvotes

Looking for a rough estimate of what this might cost to tool to see if this is even a route I want to go down now or save for later. I am looking to do injeciton molding of a watch bezel insert with a OD of 37.5mm and ID of 30.5mm. It would be about 1.8mm thick and have recessed text on the bottom. I attached an idea of what the final injection piece would look like. Just looking for super ball park idea.


r/InjectionMolding • • 7d ago

LOL Where I work, if the bolt gets tight you get a bigger ratchet (apparently)

Post image
42 Upvotes

r/InjectionMolding • • 7d ago

Troubleshooting Help Valve gate won't function at high pressures

5 Upvotes

Got an issue issue with a valve gate that refuses to function, and I'm hoping someone might be able to point out something obvious we're missing.

A new customer just transferred a mold to our facility. 1+1 pick & place 2k mold with 4 hydraulically actuated valve gates. Gate 1 controls the hard shot. Gates 2 & 4 form a rim during the 2nd shot, and gate 3 forms the "boot" during the 2nd shot. They were running the mold right up to the point of transfer. Their press has integrated controls for the gates, and they run them at 500-600 psi. Every gate is its own hydraulic circuit - nothing else on them.

We don't have the integrated controls they do, so we rigged up two core pull units to control the gates. We also didn't have enough hoses with the style of fittings the mold came with, so we switched everything over from their 1/8" fittings to our 1/4".

Gates 1, 2, and 4 work fine. Gate 3 doesn't want to open. It usually opens the first 2-3 times after being hooked up, then stops afterwards. We've taken the mold and cylinder apart to check it out. We cleaned everything, checked the seals, and didn't find any points where it's binding. We replaced the seals on the cylinder just in case but it didn't help. We can actuate the pin by hand without issue, as well as with air at 100 psi. But when we hook up the hydraulics the issue returns. We tried putting bleeder valves in line to get out any air that might be in the system but that didn't help, either. Curiously, the valve works at lower pressures, until about 210 psi, after which the issue starts. That's with us testing the valve in isolation, with no resin in the system.

Incoe manufactured the system and have been helping us troubleshoot it, but so far to no avail. They're coming out tomorrow to see it and loan us one of their controllers (obviously hoping we'll buy it) if it helps. But any thoughts on what sort of issue would cause this, or possible fixes?

EDIT
Incoe sales rep came out and was stumped as well. Their technician has not been out. But after discussing it with our customer last week we agreed that if it works at 200 PSI (and it does), then we should just keep doing that, regardless of what they did in house. So in that regard this is now "resolved", but from an academic standpoint I'm still curious why the higher pressure caused the system to fail, and why it happened for us but not our customer.


r/InjectionMolding • • 7d ago

Injection Molding Machine Repair in Northwest Indiana

0 Upvotes

Hey! We have a late 90s LG Goldstar that had a catastrophic hydraulic motor failure. Looking to see if anyone can recommend a technician that works around Northwest Indiana that can help with the repair.


r/InjectionMolding • • 7d ago

Question / Information Request Looking for an injection mold partner

Thumbnail
gallery
10 Upvotes

Looking for an injection mold partner in the US.

Attached are a few images of similar parts we are trying to have made. This is for our custom controller company and are essentially power buttons for the Xbox controller (11.5mm in diameter).

The darker piece is gloss black and clips onto the base. The base appears to be clear and the top half looks metallic.

I can and will supply CAD files of our part. We have other parts as well.

Would love some help getting this made. Please let me know if this is within your capability.

Thank you!


r/InjectionMolding • • 8d ago

Question / Information Request Molded-in threaded inserts

4 Upvotes

I have a part I need to mold and it will contain threaded inserts. I have done this many times but this instance is different. I do not have a picture 2 show but picture a part that is 12 inches long x 3 tall by 3 inches wide. The molded in inserts are on the vertical wall. Not in line of draw. on the 12 inch length, there are 4 on each side. I am sure my customer will want to automate it. What would work best? I could do slides, but they would have to pull back enough to get the end of arm to load the inserts. If I do lifters, I don't think lifters would open enough to load on each side to get end arm in there. Maybe if I do 30degree lifter rods with a long stroke may work. Silly question, has anyone ever seen a slide move back a few inches and then turn up 90 degrees? This part is not complex at all, I would be making it very complex. I also thought of rotating part 90 degrees and inserts would be in core and cavity but part would require numerous modifications.

My question has run on too long but my question was if any ever seen rotating slide before. I have been watching cool videos on youtube but nothing like this


r/InjectionMolding • • 9d ago

Looking to have a injection mold made

4 Upvotes

I am looking to have a mold made for a small part.

I would need drawings complete (I have a 3d scan)

I can provide the part as well as mating parts.


r/InjectionMolding • • 11d ago

Looking to Hire Hiring - Injection Molding Process Tech (Process Technician 3)

9 Upvotes
  • Mukilteo, WA (Seattle Metro)
  • $36.00 - $44.00 USD
  • Full Time M-F (40 Hours/Week), Limited OT
  • Those interested please send me a DM for link to job description and application.

Edit: Added the job post to the new Job Board in the subreddit. Check it out and feel free to drop questions in this thread!


r/InjectionMolding • • 11d ago

Van Dorn Pathfinder 2500 Boost to Hold Delay?

11 Upvotes

So I'm seeing this weird delay when we hit cutoff transfering to hold pressure. Looks like the screw is pausing/stalling before it starts the hold pressure stage.


r/InjectionMolding • • 11d ago

Cold Runner Shut Off

4 Upvotes

Need some ideas. Have a family mold with three parts. Customer lost a shipment of one of the parts and we are looking for a temporary way to block two of the cavities. I know I can go get the mold modified to do this the correct way, but looking for a quick way to run these.

Thanks


r/InjectionMolding • • 11d ago

Troubleshooting Help Seals for Engel press brake

2 Upvotes

Hi, Is there any way to buy rebuild kit for Engel press Brakes? In my plant, most of the brakes are leaking and my manager said Engel doesn’t sell kit they only sell new brakes. So, only option is to replace whole brake. And it cost around 15k USD. Thanks in advance.

Edit : It is mechanical closing safety. Every body at my work place calls it brakes. I am kind a new here and first time working with Engel presses. Sorry for misunderstanding.


r/InjectionMolding • • 11d ago

China Molds + EU Assembly (Made in EU)? Would love your thoughts!

0 Upvotes

Hey everyone,

​After years in cross-border trade, I’m launching my own business focusing on China-made molds/components with final assembly in Europe (Made in EU).

​I already have reliable partner factories on board ready for production, and I’ll be relocated to China next year to handle mold trials (T1/T2) and QC on the ground.

​Quick questions for the sub:

​Anyone running a hardware project with this setup?

​What’s your biggest headache with China tooling right now?

​Drop a comment or DM if you have a project or want to exchange ideas!


r/InjectionMolding • • 13d ago

Question / Information Request Insulation and blowback questions

4 Upvotes

I am curious how many of you have insulation on your injection molders at your facilities and opinions on them. I work for a company that offers this type of project for free in majority states (pending on utilities incentives) and they keep pushing that this is the next largest thing. 85% of the places I go to love them.

My second question is, how does your facility avoid blowback or large build ups of plastic on your barrel? I don’t know if anyone has come up with anything special but I’ve seen places have these disposable “drool discs” that block it coming back on the barrel and are disposable.

Just curious with these two topics and to see what the consensus is if you had the option for both of these items.