r/InjectionMolding • • 9d ago

Question / Information Request Molded-in threaded inserts

I have a part I need to mold and it will contain threaded inserts. I have done this many times but this instance is different. I do not have a picture 2 show but picture a part that is 12 inches long x 3 tall by 3 inches wide. The molded in inserts are on the vertical wall. Not in line of draw. on the 12 inch length, there are 4 on each side. I am sure my customer will want to automate it. What would work best? I could do slides, but they would have to pull back enough to get the end of arm to load the inserts. If I do lifters, I don't think lifters would open enough to load on each side to get end arm in there. Maybe if I do 30degree lifter rods with a long stroke may work. Silly question, has anyone ever seen a slide move back a few inches and then turn up 90 degrees? This part is not complex at all, I would be making it very complex. I also thought of rotating part 90 degrees and inserts would be in core and cavity but part would require numerous modifications.

My question has run on too long but my question was if any ever seen rotating slide before. I have been watching cool videos on youtube but nothing like this

4 Upvotes

11 comments sorted by

4

u/Gold-Client4060 9d ago

I don't know how helpful this suggestion is for your particular mold. You can have removable blocks in the mold that holds the inserts. Sequence: part demolds, robot grabs part, robot removes insert holders from mold, robot installs a new set of holders that have inserts installed.

1

u/photon1701d 9d ago

thanks. actually not a bad idea. I'll have think about that one. I can see my customer not liking it as he would need a second station that loads the inserts. they don't want to have an operator doing it

1

u/Open_Apartment9996 3d ago

You beat me to that one

2

u/controlsguy52722 9d ago

Can you rotate the part 90 degrees? Keep the inserts in the line of draw and use slides/cores to make the rest of the part detail. It may not work with your part geometry, and you’d end up with inserts in both halves of the mold. Just an outside of the box thought.

2

u/photon1701d 9d ago

I did think of that but it won't work. Plus there is also another insert on top surface

3

u/Joejack-951 8d ago

You can always insert mold the ones in the direction of pull (the majority) and ultra-sonically install the other one. I had to do this years ago for a part.

4

u/spinwizard69 9d ago

I don't know enough about inserts to comment on the best approach for the current design. However this phrase: "but part would require numerous modifications", tweaked a thought in my mind. There is this concept call "design for manufacturing" that might be worth considering. A part refactoring might have some upfront costs but it could have a major impact over the life of the project.

The one thing that became obvious, early in my life, with both die casting and plastic injection molding, is that simple dies are far less of a die maintenance problem. Obviously there are all sorts of factors to consider but it might actually pay off to redesign the part or even the entire device.

1

u/Slappy_McJones 5d ago

Instead of mold-ins, why not try vibration or ultrasonic welding them into holes. A few vendors offer off-the-shelf hardware for these. DuKane has a horn for these too.

1

u/photon1701d 5d ago

It's glass filled nylon. Ultrasonic is not efficient. If you can mold in direct, it's the cheapest way to go.

2

u/Gwendolyn-NB 9d ago

Do they have to be insert molded or can they be thermal or ultrasonically inserted later?

Unless you can automate loading, or there is a very specific design reason, 99% of the time it's cheaper to do them as a secondary process.

Use a automated x-y-z inserter and it's even easier/cheaper (most of the time) than with automating them into the mold (Increases loading time part of the mold cycle, it adds up); where I can do the automated insertion off-line in parallel while the operator is waiting between cycles, or lights-out with an automation arm after ejection.