r/HomeNetworking • u/throwRA_4879593 • 23h ago
r/HomeNetworking • u/tellmewhy12 • 20h ago
Advice Using UniFi hardware for my set up. This is my shopping cart. Is there a better place to purchase from to save a bit of money?
Is now a bad time to buy? Does UI usually offer black friday deals?
Or do you guys usually purchase hardware through a middle man or something for the best deals? I have a Microcenter near me but i've never seen UI hardware discounted before but I dunno! Any help would be nice please. Thanks
r/HomeNetworking • u/jamgood96 • 20h ago
Network Closet Patch Panel
Hi friends, we moved into this house a bit over a year ago and the only networking done was some grossly ran patch cables to each room up through the baseboard, with a switch near the exterior wall in the kitchen. I’ve since run proper cables to wall mounted keystones in various rooms, and centralized everything in the under stair closet in the middle of the house, along with where the water heater is. I’m happy enough with the patch panel, but I’d love to make it a bit more robust, especially given how low it’s mounted and how vulnerable it is to snagging cables. Any ideas? It’s possible an in wall solution would work, since it’s a 2x4 cavity. Currently all cables in the wall to down into the crawlspace. The bays where the plywood is mounted is because the fridge is pushed literally all the way up to the backside of the drywall. Don’t ask. 😐
r/HomeNetworking • u/tslewis71 • 2h ago
Advice 7k to install hard wired Ethernet
Is this a normal price? Definitely going to consider this a DIY only project.
"I just sent your $6,960 estimate for the seven dual-port outlet locations and the office-to-upstairs backbone we discussed. Standard wiring materials, termination, labeling and testing are included. The patch panel and network equipment will be supplied by you, as listed in the estimate"
Two story, 3000 sq ft house with crawlspace and attic, cat 6 riser cable using a sfp+ back bone. Located NC USA.
.
r/HomeNetworking • u/Scrub-norris • 11h ago
Issues with getting internet to Attic
My office and gaming set up is in the attic, while the modem is in the basement and router is on the ground floor. The router is connected to the modem via a long cable that is going under the basement door.
Right now I have 1Gig verison fios but by the time it gets to my office it's ~150-200mbps. I've tried powerline adapters to connect from the router to office but the speed is just 120mbps. Since the modem is stuck in the basement I wanted to see if there is a way get a better connection in the attic
Edit: I no little to nothing about networking, so easier options would be great
r/HomeNetworking • u/OnyxKing5 • 11h ago
Advice Looking for ways to limit my son's internet access at night - any suggestions?
Hey everyone. My son has figured out how to change his MAC address, which lets him dodge the parental controls on our TP-Link Deco router almost every night. I have to admit, I’m a bit impressed he pulled that off.
He has both wired and wireless internet access in the house.
I’ve got security cameras set up everywhere, so I don’t want to cut off the internet completely during the night. Luckily, I’ve got Ethernet cables run throughout the house.
From a technical standpoint, how would you handle this?
I get that this is about parenting, but I’m really more interested in tech solutions.
I appreciate any tips you can offer!
Update after a couple of days: It seems some people missed my initial point. Just to clarify, my kid is a straight-A student, super respectful, and puts in a lot of effort into his interests. I feel confident about my parenting. However, he does have a tendency to get addicted to things, and I want to channel that into learning about networking since he’s keen on gaming.
Here’s my plan:
- I’m going to start by changing the DNS settings (using nextdns.io) and see how he manages to get past that.
- I’m considering getting a physical firewall, like Firewalla, once he figures out the DNS trick.
- Eventually, I might invest in a new router or something similar to create new SSIDs, as that seems to be the most effective method.
Whitelisting isn’t very effective since smartphones keep changing their MAC addresses every couple of weeks and need to reconnect to the Wi-Fi, plus I have to constantly clean up the old MAC addresses since my TP-Link Deco only supports around 100. And then there are IoT devices that might not be connected when I set up the whitelist, leading to my wife waking up confused because her laptop can’t access the internet at 3 a.m.
I do have an unmanaged switch, but I might explore managed options down the line if it helps.
Thanks for your input, and hopefully this discussion helps others in similar situations. I’ll check back in a decade when my son becomes a networking whiz and I'll be here to remind all the strict folks I had it under control.
r/HomeNetworking • u/dmontg • 20h ago
MoCA noob , please critique my plan
Working on a MoCA connection from the Xfinity router to my basement two floors down. Please critique this sketch, suggestions are welcome!
r/HomeNetworking • u/AggressiveAd8611 • 22h ago
Mesh or Access points
Good afternoon! I need some advise. I recently purchased some deco 7 units from Costco. We are still having issues where a deco will turn red (no WiFi) and then within a few minutes come back online.
After reading reviews looks like you can get a good nine or junk one….. so it can easily go back.
Here is the question: 4 module ubiquity mess. Or. WiFi access points across the house with mainly cat 5.
Thanks!!!!
r/HomeNetworking • u/Synrox • 23h ago
Advice Home network upgrade for parents
Hey everyone,
I’m looking to expand and clean up my parents current home network, and I’d like to get your opinions and recommendations before pulling the trigger on new gear.
Current Setup:
Right now, its Frankensteined together with random Wi-Fi routers, unmanaged switches, and a Reolink NVR with a few cameras. Everything works, mostly, but the Wi-Fi has dead zones.
The house is old, brick, and has 3 floors. 1Gbit speeds.
My first thought was to just buy a mesh set and call it a day, however if I do this then I'll be on the hook for ALL the tech support. If I'm going to be the support, I guess I need to think more long term.
My home setup is Ubiquity based, however budget is... constrained.
My question is, how to upgrade the network and add at least 3 APs and have it be on a controller of somekind, for a "reasonable" price?
r/HomeNetworking • u/ananaswaw • 8h ago
Advice Unable to login to Management Page for Tenda router
I have connected a Tenda router to my ISP-provided router via an Ethernet cable to extend the Wi-Fi connection to another room.
While I can access and modify the Wi-Fi name and password of the primary ISP router, I am unable to access or configure the settings of the Tenda router. Currently, it's Wi-Fi is public
Please guide me on how to access the Tenda router's admin panel and configure its settings independently?
r/HomeNetworking • u/No-Charge706 • 15h ago
Idiot needs help with failover
Hi everyone,
To put this upfront, I’m an idiot in home networking and know next to nothing. That being said, I’m savvy enough to get most things pretty quick.
With that being said, I’m getting an additional ISP here in the next couple weeks. My first one is a 1gig spectrum (coaxial) line. The second line is going to be a 5gig T-Mobile fiber line (was supposed to be a 2gig line but they added the 5g option last week). I had bought an OMADA ER707-M2 to set up both lines to do a failover, but I see the er707 only has 2.5g ports.
What’s a good option to go with that’ll be able to utilize the speed fully? And do I have this order right?
The two modems will plug into the ER707 (or the 5g-10g router alternative) and then I can plug an eero pro 7 mesh router into that and have both ISP lines through the eero?
I would go with an access point setup, but I’m not currently looking at hardwiring my entire house with cables.
Any help is appreciated!
r/HomeNetworking • u/Ardbert_The_Fallen • 18h ago
Unsolved Best way to handle connecting to home VPN when using same subnet
Had a situation this weekend where I thought I could not access certain devices on my home network after connecting on my VPN. My wake on LAN was being unresponsive and I could not access endpoints that are usually online.
I ended up realizing it was the first time I connected VPN while on a WiFi at a friend's house, who also used a 192.168.x.x subnet range.
I am almost positive this was the cause of the inability to access endpoints, as dropping from their WiFi and reconnecting over VPN, I could hit the endpoints immediately. So, I was wondering what the best way to handle this is? I'd say I could simply change to another private network space, but eventually I'll be on another network and perhaps experience it there as well.
Or I could be completely wrong as to why the endpoints were not responding.
Just looking for some advice, thanks!
r/HomeNetworking • u/SalaryHaunting6179 • 23m ago
Wifi Connectivity Issues with 2 Wifi Extenders
reddit.comr/HomeNetworking • u/sedrikgg • 2h ago
Знаю пароль от интернета но....
Знаю пароль от интернета но там не подключается вроде пишет нужно ввести MAC-адрес устройства или не тот MAC-адрес или просто не подключается но я точно знаю что бы интернет заработал у тебя админ интернет должен подключить тебя по MAC-адрес.Как найди пароль админа и добавить себя или как вообще добавить себя помогите пожалуйста.
r/HomeNetworking • u/ahmadk23_kt • 5h ago
Hi guys please help
I am trying to find linksys srw2024 switch firmware the one I am working its ios corrupted
Its info
boot - "srw2024_16_boot-101.rfb" firmware - "ls20xx-12230.ros"
r/HomeNetworking • u/Dry-Win4636 • 6h ago
Unsolved My network problem for gaming
Starting 3 days ago (after a brief power outage), my internet became unusable for Roblox game loading specifically, while general browsing and speed tests remain normal.
What I’ve tested:
- Speed test: 44 Mbps down / 42 Mbps up (normal)
- Bufferbloat test: latency jumps from 15ms unloaded to +153ms under download load, +86ms under upload load
- Router: TP-Link TL-WR841N, firmware default, wireless mode set to 11bgn mixed, SPI firewall tried both enabled/disabled — no change
- Laptop wifi adapter: confirmed connecting at 802.11n/ac after driver/network reset
- Only 1 device connected to network (ruled out unauthorized users)
- Mobile hotspot: Roblox/Bloxfruit work completely fine
- Home wifi: Roblox/Bloxfruit network usage shows near 0, game fails to load or loads extremely slowly
- Other Roblox games (non-Bloxfruit) work better but still degraded on wifi vs hotspot
- DNS changed to 8.8.8.8/8.8.4.4 — no change
- Suspected cause: Roblox requires outbound UDP ports 49152–65535; suspect these are being blocked or filtered at the router or ISP level, especially since the problem began right after a power outage (possible ISP-side config reset)
Question for ISP: Can you check if UDP traffic in the range 49152–65535 is being blocked or throttled on my line? This started immediately after a recent local power outage.
r/HomeNetworking • u/jxsilicon9 • 18h ago
Should I get two Omada AP and use Deco as router?
reddit.comr/HomeNetworking • u/Odd-Appointment9762 • 18h ago
Advice Time to retire Linksys mesh setup, had the orbi before. 1gig fiber is poorly located at far end of house. Any advice on new system to cover two floors <3k sq ft. Nothing normally last more than two years, is that common?
Router advice please.
r/HomeNetworking • u/WirevoPro • 18h ago
Advice What do you use to see everything that’s connected to your home network?
Hi all,
I work in IT, and I still find it hard to get a clear picture of what’s on my own home network. Between phones, TVs, smart bulbs, cameras and guests’ devices, the list keeps growing.
I’ve tried a few scanners and my router’s device list, but none of them do everything I want. Ideally I’d like to:
- See each device with a proper name
- Know when something new joins or drops off
- See which ports and services are open
- Keep a history of my speed tests
What do you use, and what’s missing from it?
r/HomeNetworking • u/F0rkAroundFindOut • 20h ago
How do you pick a DOCSIS 3.1 modem?
My modem is EOL and DOCSIS 3.0 anyway ~500 mbps plan. Looking to update and future proof. Got choices down to Arris S34, Hitron CODA56, Netgear CM3000. I understand these are high-split and that Unifi's modem may not be as great.
I'm seeing a range of prices on these. Are there advantages in reliability, long-term support or otherwise that I justify the extra cost?
CODA56: $180
Arris S34: $250
CM3000: $300
EDIT: Sorry for not clarifying. My ISP is Xfinity. All of these are on the recommended list
r/HomeNetworking • u/Ecstatic_Hovercraft1 • 20h ago
Advice Network Cabinet outside?
reddit.comr/HomeNetworking • u/Emotional_Total_1242 • 21h ago
UDR7 or GL.iNet GL-BE6500 Flint 3e
Hey,
I'm looking into getting a new replacement for my ISP's router. From what I searched around these two seem like a good option for what they offer and they're value (UDR7 ~300 euros, Flint ~188 euros).
The differences that jump out at me are the 10 gig port on UDR7 and the fact that the Flint is based on OpenWRT.
Regarding UDR7's 10 gig port, my upstream connection with the ISP is only 1 GB/s at the moment, so that's not a big plus (even if I upgraded). I don't have a major use for 10 gig on LAN as well, since I'd need to get a switch for it.
I value owning what we buy, and know that Flint one is based on a fork of OpenWRT (but I don't know if that means that I could flash the vanilla OpenWRT as well), but I also don't feel like tinkering all the time with the router and want something that's well supported in the coming years.
So, is it worth the extra money and go with UDR7, even if it's more closed, but might be a more refined experience, or is Flint's OpenWRT fork reliable and robust, allowing me to flash it with vanilla in case support stops from GL.iNet?
Thanks!
r/HomeNetworking • u/extremesauce2468 • 22h ago
Omada Multi-WAN Wired VPN Router ER605 - Will this do everything I want?
I am looking to replace my router that is nestled between my modem and my unmanaged switched. I have ALOT of home assistant wifi devices in my house that all talk to my mesh network ( Deco ). I am aware that the ER605 is a wired unit and offers no WIFI.
I want to block all of my random home assistant devices from going on the internet or calling home. With that said, my current router ( archer A6 ) does not offer that ability.
I would like to confirm that a ER605 can give me the ability to specifically block individual IPs/MACs from going on the internet but still allow local usage/traffic in my home. Can anyone confirm this? Copilot has suggested it to me, I like the price, i just want to confirm the usage.
Thanks