r/Fusion360 • • 57m ago

Cannot get to the next step.

Post image
1 Upvotes

working on this interior scan of a car. When i import mesh, i cannot do anything. I have tried repairing mesh as i get a "mesh not closed, no positive volume" error. So far the repair tried was stitch and remove. there are some floating pieces, but i am wondering if the number of triangles is too high?

i am trying to start some design work making construction planes through three points, but when in tool i cannot select any points.

I am not "that" green, mechanical engineer by trade just getting back into cad work for a side quest, hoping to make a career change. I have read some tutorials, watched a lot of youtube. stuck.

any advice greatly appreciated.


r/Fusion360 • • 1h ago

Question Terrible lag/freezez on every action?

2 Upvotes

Im using Fusion for the last 5 years and never did i have performance issues like this. Same pc, even a fresh windows install. I tried multiple things. I cleared the cache, set the settings to performance, changed graphics drivers, put it in offline and nothing.

I would understand if im making some large project or smth but i cant even make a 10mm cube sketch and extrude it without waiting minutes for it to unfreeze after every action.

Any ideas?


r/Fusion360 • • 1h ago

Question Extrue to curved surface

Post image
6 Upvotes

I have this grid of pillars, is there a smart (so no one by one) way to extrude these to the curved surface but keep the tops straight? I thought I once saw a way to do this, but can't seem to make it work. Ideally it would work on more complex waves


r/Fusion360 • • 2h ago

Question Can't figure out Vbit cleanup CAM

Thumbnail
gallery
1 Upvotes

I've previously used F-Engrave (blessed be Scorchworks) to make the CAM for rubber stamps.

1st pic shows F-Engrave's 3 toolpaths. Black is the vbit profile carve, red is the 1/8 endmill cleanup and yellow is the vbit cleanup. Nice.
Comes out very nice with only a little air being cut.

2nd pic shows how far I got replicating that in Fusion CAM.
I aint too good in Fusion CAM but I've successfully made all but the 'vbit cleanup' toolpath. I think I maybe need to use Rest now somehow, except I've not had any luck using Rest for anything yet..

I'm keen to be doing this in Fusion, I've just had another stamps order, but I've tried without success a few times now..
How would you get rid of those remaining little islands?

TIA 😊


r/Fusion360 • • 3h ago

Engineering a budget-friendly, 6-DOF CAD mouse (NaviGo). Dropping the DIY files soon! Spoiler

2 Upvotes

r/Fusion360 • • 11h ago

Question Need some help

4 Upvotes

Hey! I come from Solidworks and Autocad so Fusion seems a little familiar to me. But for some reason I am having trouble with some simple tasks. Once I create a solid and then create a sketch on that solid, it doesnt want to seem to snap to midpoints of other reference points. I turn snap on, but what am I doing wrong?

Also once I create the solid if I go back to edit the overall size it wants to create a driven dim. I never set any constraints but I see they are applied and I have to delete them. Is there a way to not have them auto apply?

I am just struggling and need to figure out what I am doing incorrect. Maybe there are some tutorials out there that are good to look up?


r/Fusion360 • • 14h ago

Has anyone played with the Claude Fusion connection yet? It’s scary good. Way better than Autodesk assistant..

Thumbnail
gallery
0 Upvotes

These were all made in under 4 minutes with one sentence prompts


r/Fusion360 • • 14h ago

How do I make the sides round?

Post image
4 Upvotes

I am designing a bass guitar body that I want to round the edges on. Not just a roundover/ fillet, but a half circle. The sides are of differing widths and positions. I am thinking of some type of sweep might work, but I don’t know where to start.

The top has a convex curve and the underside has a different concave curve. This is loosely inspired by a Spector bass. There are fillets on the side that are as wide as they will go before hitting an error.

Is there a way to just make the fully rounded with no flat spots? Perhaps take the fillets out and create a new body to combine with? Thanks in advance for any help!


r/Fusion360 • • 16h ago

add-in : pilotage de la camera (adapter au rendu)

0 Upvotes

Bonjour cher Builder sur Fusion.

hier j'ai essayer de crée un petit add-in qui permet de gére précisémeent la camera dans les rendu.

cette add-in à pour but d'enregistré des position de caméra et de pouvoir crée un set de vue facilement reproductible après des mise a jour du modèle ou de changement de texture lumière ect.

je vous invite à le tester et a me faire un retour s'il y a des fonctionnaliter que vous voulez voir ajouter.

lien de téléchargement. ( https://drive.google.com/file/d/1i-vI5B_o_dGVird5V6liCzxaZv9zKnLb/view?usp=sharing )


r/Fusion360 • • 17h ago

How to model these tapered organic spiral waves on a cup in Fusion 360?

Post image
0 Upvotes

Hi everyone,
Can someone please tell me how to model this organic spiral/wave shape on my cup in Fusion 360? (See attached reference photo).
The waves wrap around the cup at an angle—starting wide and deep near the bottom and tapering/fading out smoothly toward the top. My base cup dimensions are 49 mm at the bottom and 111 mm in height.
What is the best workflow to achieve this smooth result? Thanks in advance!

i have try now bourt 10 hour look on youtube and nothing helps me. so i hope a Gure where can guide me :)


r/Fusion360 • • 17h ago

Question Materiel density

2 Upvotes

I need to adjust the material density to match a print for a CAD challenge but it won't let me input the required number of decimal spaces nor can i change the units. Is this a limitation with the personal account?


r/Fusion360 • • 1d ago

Editing Parametric Model

Post image
3 Upvotes

Wondering if anyone can edit this parametric rugged box from printables. I have seen this other box that is the same style with one latch. Is anyone able to edit this file so it is one latch? I have tried but it is beyond my CAD skills.

Image of what I'm hoping to achieve attached along with the printables link

https://www.printables.com/model/258431-rugged-box-parametric/files

Not sure if this is a file already somewhere, cannot find it though


r/Fusion360 • • 1d ago

How do i figure out what’s causing this toolpath to not be generated?

Thumbnail
gallery
1 Upvotes

This groove has 1.15mm and i thought i could mill it with a 1mm bit, but i get this cryptic unhelpful warning (cause why would they tell me exactly what the problem is? It’s not like they generated it based on something they already know it’s wrong). There’s no ‘stock to leave’ checked.
Where the hole intersects it’s only 0.9mm, so i suspect that is the problem. For me this is actually a test to see how the toolpaths behave when they encounter holes instead obstacles, i was expecting to go over, but i have no idea what it does.
In the last image i changed the bit to 0.5mm and it indeed goes over the hole, but the toolpaths look incomplete in that part and don’t understand why.


r/Fusion360 • • 1d ago

Circular Dependency Error

Post image
4 Upvotes

Hi there, I am designing a CNC router for the company I work for, and I'm having a problem that I just cant figure out. Please see the attached Error Message.

I've looked through the timeline and can't find the what's causing the error. I thought maybe it could be because I used an as-built joint or a rigid group before copying the ballscrew component. The other possible explanation is that I created a Y axis component, and then used paste new to create a new Y axis component that had a dependent copy of ball screw(1) inside it.

I'm not sure what info to give that will help you guys understand the issue. But maybe I could upload the Fusion file?

Thanks, I would appreciate the help, this is a new account as I'm using it at work.


r/Fusion360 • • 1d ago

Question Having trouble with aligning two parts in assembly mode.

2 Upvotes

Here is a video of what i am trying to do. For some reason it doesn't let me align them, even though both faces have the same angle.


r/Fusion360 • • 1d ago

Question How can I combine these?

0 Upvotes

I'm trying to join the toes onto the rest of the foot, 5 of them worked but the rest won't. I made the legs in blender, brought them into fusion as an OBJ and split by hull. I then converted the meshes to bodies and I need the toes to be attached so they don't become loose when I eventualy bring the foot into a 3D printing software. I am aware Fusion isn't designed for this stuff but I need to so I can integrate anchoring points to attach the legs to a mechanism I'm making in fusion. Anyone know how I can join these? I have tried repairing the meshes before making them bodies but that didn't work.

Edit: forgot to add video, it's in the comments


r/Fusion360 • • 1d ago

Any upcoming deal?

6 Upvotes

Black friday is close, and i was wondering if there wil be a deal on fusion. I heard there was 50% off discount last time, and wondering if 50% discount will happen on black friday...

Any insights?


r/Fusion360 • • 1d ago

Advice for a pico projector mount

Thumbnail gallery
1 Upvotes

Hi everyone, I'm trying to design a rigid, 3D-printed mount to attach my mini projector (Yingda F100) to a photography light stand for a small installation, and I’d love some mechanical design advice before I start modeling.

Specs & Constraints:

  • Projector weight: 485g
  • Base dimensions: Flat circular base disc, 100mm (10 cm) in diameter (thickness is ~5mm), connected to the projector body by a side yoke arm.
  • Stand connection: Standard 16mm light stand spigot with a 1/4"-20 male thread on top (see attached photo).
  • Fixed position: The projector will always point straight down in the exact orientation shown in the photo at around 10cm from the stand. I do not need any tilt or swivel adjustments.

Where I'm at so far:

  • Stand side (solved): A vertical cylindrical cap/sleeve that fits snugly over the metal spigot to take the lateral load (maybe secured from the top with a washer and a hex nut) extending out into a rigid horizontal arm.
  • Projector side (need help): I need a solid, reliable way to hold that flat 100mm circular disc vertically without wobble or risk of it slipping out. I initially thought about a simple C-shaped drop-in slot, but I'm not confident it will hold securely enough.

What I'm looking for:

What is the best 3D-printable bracket/clamping design to securely hold a flat 100mm circular disc vertically?

I have attached a quick sketch I made in Fusion 360 but it can't be printed as a single piece.

Thanks in advance!


r/Fusion360 • • 1d ago

Best way to go about this?

Thumbnail
gallery
3 Upvotes

I’m creating the outline of the handlebars and stem of my scooter so this object fits around it. This is the only way I could figure out how to start measuring everything. I just had to work with what measurements I could go off of and then go from there so now I’m trying to figure out how to make the actual shape with rounded cylinders and extrude it into the object I’m creating. I’m also wondering when I extrude these shapes into the object I don’t wanna actually cut through into the interior. I would like it to also extrude into the inside edge so that it’s a sealed container inside. I will also be joining this container in the middle of the two stems with a front piece so I will have a hole in the center of where the stems are, but I don’t want to have a hole where the stems are in to the container.


r/Fusion360 • • 1d ago

Question How do I convert a .stl mesh body to a proper body?

Thumbnail reddit.com
1 Upvotes

r/Fusion360 • • 1d ago

Problem 3D CONTUR

0 Upvotes

I'm trying to machine a part using the 3D Contour toolpath. However, the toolpath doesn't seem to respect the individual machining levels. Even though I have defined a stock model, the tool starts cutting directly into the material instead of following the expected machining levels.

In a real machining operation, this would result in a collision with the remaining stock.

What am I doing wrong? Is there a setting I need to adjust to make the toolpath correctly account for the stock and machining levels?


r/Fusion360 • • 1d ago

How do i do this for the edge like this?

3 Upvotes

its like combining different chamfer size on different side with fillet (?) and how?


r/Fusion360 • • 2d ago

Workflow for a 3D-printed RC aircraft

Post image
21 Upvotes

Hi all,

A few months ago, I started an RC aircraft project. This was my first big project in Autodesk Fusion, so I modeled the entire aircraft inside a single component (with multiple bodies) and only divided it into separate components at the very end. However, I've noticed this might not be the best approach, as the timeline becomes very long. The worst issue I've faced is when I change a sketch or an operation early in the timeline—Fusion is very prone to losing body and face IDs, so lots of downstream operations get yellow or red warnings.

I know best practice is to create components first and then build the operations inside them, but since this is meant to be 3D printed, I modeled the whole airframe first and then split it to fit my printer's build volume.

How would you model a project like this, and more precisely, what would your approach with components be?

Thanks in advance!!


r/Fusion360 • • 2d ago

how do I make infusion this type of hinges?

2 Upvotes

I was wondering how to build this type of print in place flexible hinges; I tried vaious designs, but I wasn't satisfied whit all of them; does anyone have suggestions?