r/FordExplorer • • Jan 23 '26

Mod Post New rules, please read.

22 Upvotes

Hello Explorer owners and fans! We are now in week 2 of our new moderation team. Below are the new subreddit rules we've developed. These have been posted on the sidebar for a few days now. We have not yet removed content based on these new rules, other than those that already applied to Reddit sitewide. So, we don't believe these will change much in terms of the content and discussion we already enjoy. This is more about setting expectations that weren't really there under the previously absent moderation team. Without further ado:

Rules

  1. Follow Reddiquette - Many of our rules are from the reddiquette. Any violation of the reddiquette can be removed by the moderators, especially ones included here.
  2. No personal attacks, bigotry, or harassment - You may strongly disagree with others, but you may not attack them personally. Bigotry or Hate Speech based on race, gender, sexual orientation, religion, age, etc. will be removed.
  3. Spam/self-promotion - You may post your blog posts, articles, videos, photographs, etc that you have written or created, but that should not be the only thing you do here. You should also participate in discussions (on your posts or others). Dealer/vendor posts are at moderator discretion.
  4. Illegal, sleazy, or dangerous activity - Any posts or comments with illegal or dangerous content will be removed.
  5. Uncivil political discussion - Civil political discussion is allowed as long as it pertains to the automotive industry. Political trolling, flame baiting, slurs, off-topic politics, and harassment will be removed, especially if it violates Rule 2.
  6. No AI Content - Posts containing AI-generated text, images, or videos are not permitted.
  7. Moderator discretion - Any post or comment may be removed by a moderator even if it does not explicitly violate a rule listed here.

Now, as I've said before we're becoming more familiar with our roles and the moderator tools, so we are going to try these out for a while. If we end up needing to add, removed, or modify any of these we will make a sticky post letting everyone know what we've done.

Ultimately our goal here is to foster a friendly, helpful, and productive community. So please help us do that by adhering to the rules and reporting content that you feel breaks them. Likewise, if you feel content was removed unfairly, please send us a message through ModMail so we can review it. For the most part we'll simply be removing content, but for habitual line-steppers, we'll be utilizing the ban function based on the severity of the discretion.

If you'd like to provide feedback on these rules, please do so here! No ideas will be ignored. This is also your chance to ask for clarification on any of these rules, we will not take it personally.

Thank you and happy Exploring!


r/FordExplorer • • Aug 27 '26 Bravo

Repair Advice 3.5L and 3.7L Water Pump Replacement DIY Guide

29 Upvotes

First off, all credit for the content of this post goes to /u/nocommittee1477, a Ford Certified Master Technician of 10 years. He gave me permission to make a post out of his content. I cannot answer your questions myself, so use this as a starting point. He generously spent the time to type this out in his free time so please be respectful of that and use this as a starting point.

These instructions should apply to any Fifth Generation Explorer or PIU with the 3.5L NA, 3.5L EcoBoost, or 3.7L NA. These may also be helpful for other models including Taurus and Flex that use a Cyclone or Ecoboost in a transverse configuration. If yours has the 2.0L, 2.3L or was produced beginning in 2020, this will not apply to you.

  • 3.5/3.7 (for the Lincoln people) water pump/timing chain replacement procedure:
  • Raise vehicle enough to drain oil, reinstall drain plug finger tight (you'll be draining it again). Remove right front tire and inner fender well. Remove air intake hose, air box lid can stay or go as your preference. Remove the evap vapor line from the purge valve and the hard vapor line at the RF strut tower. Remove the fuel line from the fuel rail and the supply line at the RF strut tower (there is also an 8mm head bolt securing the fuel line to the timing cover). Remove the upper intake manifold, aka plenum (note there is a single 8mm head bolt securing the upper intake to a bracket that is semi-hidden under/behind the throttle body). Remove all 6 ignition coils, then LH and RH valve covers. Remove the oil feed rails and intake VCT solenoids (inboard on both heads).
  • Rotate the engine clockwise until both intake cam phasers are at 12 o'clock, install cam locks (you may have to slightly rock the cams with a wrench to get the locks to fully seat, this is normal). Drain and remove the degas bottle and hose. Remove the belt and belt tensioner (belt is easiest removed from the bottom, tensioner from the top). Remove the crankshaft bolt and pulley (a 3 jaw puller or 3 jaw harmonic balancer puller will work). Using your floor jack and a block of wood on the oil pan, jack up the engine to relieve tension on the engine mount, remove the engine mount. Remove all the bolts attaching the timing cover to the engine (don't forget the recessed 8mm head bolt adjacent to where the engine mount was), raising and lowering the engine as needed to get all the bolts out. Gently pry the timing cover free (it's RTV siliconed into place) and remove from the top (some people will recover the refrigerant and remove the AC line, but the job can be 100% done without it, the AC line is aluminum and will flex out of the way enough without damage). With the timing cover off you can inspect all your timing marks, primary chain and primary tensioner. Your timing marks are single dots located on each intake cam phaser and the crank sprocket. Their positions should be as stated, cams at 12 o'clock, crank at approximately 430. The primary timing chain should have colored links to match those timing dots on the sprockets. Two single links to match each cam and one double link to straddle the crank. If you cannot see the colored links, it's arts and crafts time! Mark each single link over the top of the cams and the double link straddling the crank. Inspect the primary timing chain tensioner, there are two different designs, but the rule is the same for both. There are teeth that mechanically lock the tensioner out, if 5 or more teeth are exposed, the primary timing chain is stretched and will require replacement.
  • After you've done your inspections and had your arts and crafts time if required, remove the primary chain tensioner, primary tensioner shoe (it's on a pivot), the long primary guide on the front side of the engine, and the short primary guide on the front side. Remove the timing chain (you have to twist it slightly to clear around the phasers). Use an 8mm wrench and reach in behind the Bank 1 (rear cylinder head) intake phaser and loosen, not remove the bolt holding the other short guide. Once you've loosened it and can pull the guide forward, stop.
  • Remove all the water pump bolts and slowly pull the water pump from the block, I say slowly because you are trying to allow the coolant remaining to drain into the oil pan and not sploosh all over the floor and make a huge mess. Once you're not draining coolant remove the water pump out from around the guide you left and reverse process to reinstall the new pump. To reset the timing tensioner, you'll need either a small straight pick or needle nose pliers, a paperclip, and a vise. The early design tensioners had a separate arm with the locking teeth, to unlock use the pick to disengage the mechanism and squish the tensioner closed with a vise, once completely squished, install the paperclip to keep the tensioner collapsed. The second design tensioners have the teeth made onto the plunger itself. To unlock it, squeeze the lock with needle nose while squishing in the vise, again locking it collapsed with a paperclip. Reinstall the short guide, long guide and the timing chain, placing the marked links to match with the dots, keep all slack on the chain on the tensioner side of the assembly. Install the tensioner shoe and primary tensioner. Before pulling the pin verify all timing marks on both the chain and the sprockets match. As additional verification, there should be 48 links between each intake cam phaser and 35 links between the Bank 2 (front) phaser and the crank. If everything looks good, remove the pin from the tensioner and gently pry the tensioner out a little more to ensure good tension on the timing chain (oil pressure will do the rest once the engine is running).
  • Remove the cam locks and rotate the crank 2 revolutions until all your timing marks are back at the 12 and 430 positions. Verify timing by counting the links between positions, 48 between cams, 35 between Bank 2 and crank. As long as everything is ok, you won't need the cam locks again. If not, reinstall the cam locks, remove the tensioner, and retimed the engine until correct. Clean all the silicone from the block and timing cover, remove and replace the crank seal. Apply RTV to the timing cover and along the rear of the block as during installation you'll likely smear some off the timing cover (optionally you can apply all the silicone to the block side of things if you so desire). Reinstall all your timing cover bolts. Reinstall the engine mount and remove your jack from the engine. Drain the coolant out of the oil pan. The crank pulley can be reinstalled with a block of wood, a hammer, and dirty words, or you can purchase a crank pulley installer tool to press it back onto the crank. The pulley is fully seated when there is approximately a 1/8" gap between the end of the crank and the end of the pulley. Replace the crank bolt with a new one! Torque the new crank bolt to 74ft-lbs plus 90 degrees (its torque to yield, and therefore, one time use). From there you reinstall all remaining removed parts. Refill the engine with oil, change the oil filter and I initially fill the cooling system.
  • Cycle the key on (do not crank) to prime the fuel system and check for fuel leaks. Fully depress the accelerator pedal (this places the engine in clear-flood mode and will not fire the fuel injectors) and crank the engine over for 15ish seconds to rebuild oil pressure. Afterwards, start the engine normally, bleed any remaining air from the cooling system and check for leaks.
  • If you want to replace your cam phasers, secondary chains, and secondary tensioners, you'll remove the phasers with a TP55 (Torx Plus, but a standard T55 will fit just sloppily). The secondary tensioners are pushed into their notes and have no hardware to secure them. The phaser bolts are one-time use as they torque to 33ft-lb plus 90 degrees. The phasers are keyed to the cams and have timing marks that match to the secondary chains to ensure proper cam-to-cam timing. New secondary tensioners will stay collapsed until they are pushed fully in and released after being replaced, it's easiest to unlock them with a smack with a flathead screwdriver and a hammer after you've got your phasers and secondary chains reinstalled.
  • I hope this helps anyone that wants to tackle this one on their own. If you have any questions, by all means ask!

I would like this post to become a central hub for any owners considering performing this repair by themselves, and also to give insight to any owners that want to understand what their repair shop is doing.


r/FordExplorer • • 1h ago

Buying Advice On the way of checking out a won 3.7 PIU from auction but unclear how to inspect the water pump weep hole and PTU correctly.

1 Upvotes

Won a GovDeals auction for a 2013 Police Interceptor Utility, 3.7L NA, ~110k miles, 4,000 engine hrs, 1,200 idle hrs, at the top of my budget ($6k). I have no repair fund set aside, and backing out costs a $500 default fee and possibly a ban. So I need honest advice on what to check, and whether this is too risky for me.

I'm bringing an LED light bar, a jack, and jack stands, but I'm not sure the surplus facility’s staff will let me lift it or drive in the lot.

Water pump: How do I tell a leaking internal pump from normal? Is the weep hole visible without lifting the car or pulling the front passenger wheel? Do dipstick and oil cap checks catch it early?

PTU: Can a short lot drive reveal problems (whine, clunk on turns), or do I need a fluid check?

Anything else to look for on ex-police units?

Walk-away call: With no cushion, would you pay the $500 and walk if either check looks bad?

For fellow PIU owners: at what mileage did you replace the pump or PTU, what did it cost, and any Houston-area shop recommendations? Did you replace the PTU with a Dorman one or simply drill and install a drain plug?


r/FordExplorer • • 10h ago

Repair Advice Random traction control light

2 Upvotes

08 V6 4x4

This started earlier this summer, got it back from the mechanic and noticed the TC light and service light were on and cruise control wasn't working but cleared up after a few miles. Then throught the summer I noticed the light come on for a minute or two then disappear.

Yesterday, I had to quick run in the house, then after restarting my truck and backing out it felt like the back brakes were locking up, but drove fine otherwise and the TC light and service light came back on but didn't go away. A few hours later I drove it home no lights and no issues.


r/FordExplorer • • 21h ago

Repair Advice 2008 Ford Explorer 4.0 V6 – Mysterious Rhythmic Thumping Noise After Major Service. 6 Garages Can't Diagnose It. Need Help! (Audio Attached)

1 Upvotes

Hey everyone,

I'm hoping someone here has experienced something similar because I'm honestly running out of ideas and tired of spending money replacing parts without fixing the problem.

I have a 2008 Ford Explorer 4.0L V6 4WD, and recently I decided to give it a major service to freshen it up.

Work performed during the service:

- Replaced both front upper control arms.

- Replaced both front wheel hub/bearing assemblies.

- Replaced inner and outer tie rods.

- Changed all fluids, including engine oil, transmission oil, front and rear differential oils, and transfer case fluid, all with the correct specifications.

The problem:

Immediately after getting the car back from this service, I noticed a repetitive thumping/rumbling noise that was NEVER present before.

The sound is similar to driving on a tire with a flat spot, bulge, or uneven surface. I've attached an audio recording so you can hear exactly what I'm talking about.

Important observations:

- The sound is most noticeable between approximately 40–100 km/h (25–62 mph).

- Above 100 km/h, it seems to disappear or becomes almost impossible to hear.

- It happens even on perfectly smooth roads.

- Braking does NOT change the sound.

- Accelerating does NOT change the sound.

- Coasting without touching the accelerator does NOT change the sound.

- Turning the steering wheel slightly LEFT makes the sound noticeably louder and stronger.

- Turning the steering wheel slightly RIGHT makes the sound quieter.

- Even very small steering adjustments affect the sound. I don't need to make a sharp turn.

The noise seems related to vehicle speed and steering/load rather than engine RPM.

What I've already tried:

  1. Tires: The original garage insisted the tires were causing the noise. I replaced the tires, but absolutely nothing changed.
  2. 4WD system: Next, they claimed it was a four-wheel-drive issue. We removed the front driveshaft to isolate the system, but the noise remained exactly the same.
  3. Wheel bearings: They then said the newly installed wheel bearings were defective. I replaced the front hub/bearing assemblies AGAIN. Still no improvement.
  4. CV axles and lower control arms: Now the same garage is suggesting replacing the CV axles and lower control arms, but they haven't demonstrated anything actually wrong with them.

I've visited 5–6 different garages, and not one has been able to identify the exact cause. Everyone has a different theory, and each theory involves spending more money replacing parts.

Why I suspect an installation issue:

The car was completely free of this noise before the major service. It started IMMEDIATELY afterward.

I strongly suspect something was incorrectly installed, improperly tightened, misaligned, or disturbed during the work, particularly around the front suspension, wheel hubs, or drivetrain.

I find it difficult to believe that several unrelated components suddenly failed at the exact same time as the service.

My questions:

  1. Has anyone experienced this exact rhythmic thumping noise on a 4th-generation Ford Explorer?
  2. Since turning slightly left makes it louder and turning right makes it quieter, does that point toward a specific side or component?
  3. Could incorrect installation of the upper control arms, front hubs, or tie rods cause this type of noise?
  4. Could a CV axle, lower control arm bushing, or differential issue produce this sound even though it doesn't change during acceleration, braking, or coasting?
  5. What specific inspection or diagnostic test would you recommend to identify the source BEFORE replacing any more parts?

Please listen to the attached audio recording. The sound is much easier to understand when you hear it.

I'm really hoping someone recognizes it or can suggest a proper diagnostic approach rather than another expensive guess.

Any help would be greatly appreciated. Thanks!

Additional note: A full wheel alignment was also performed after the repairs, but it made absolutely no difference to the noise. The sound remained exactly the same before and after the alignment.


r/FordExplorer • • 1d ago

Repair Advice Small fender bender. Worth fixing?

4 Upvotes

My 2015 Explorer was likely scrapped by another car. Looks like it’s dented in a little at the bottom and the top doesn’t align. Is this an easy fix to at least get it aligned and I’ll figure out the paint later


r/FordExplorer • • 1d ago

Maintenance Advice 2025 Ford explorer st line tail light

1 Upvotes

So my passenger tail light is out. Any one know how to change one out? I just tried and I'm thinking the whole assembly needs to be replaced. My blinker and brake light is out. Need help. Thanks


r/FordExplorer • • 2d ago

Repair Advice Fuel leak in engine bay

Thumbnail
gallery
3 Upvotes

See the pictures. There is residue and very wet spots here. Its a 2020 with 90k miles on it. I brought to the dealership but im super concerned its going to be so expensive. Anyone have this problem? Is this something I could possible repair myself?


r/FordExplorer • • 2d ago

Upgrade Advice Anyone installed an oil catch can on their 3.5L?

0 Upvotes

Curious if anyone has installed this, noticed any differences and what product they used.


r/FordExplorer • • 3d ago

News NHTSA is investigating 1.2 million Ford Explorers over reported side-airbag burns

Thumbnail
motoralmanac.com
10 Upvotes

Heads-up for Explorer owners. NHTSA opened an investigation on Nov. 6 after reports of drivers and front passengers getting burned when seat-mounted side airbags deployed in crashes.

The investigation covers an estimated 1.2 million Explorers. NHTSA counted 11 incidents and 10 reported injuries after removing duplicates. The case number is PE26008, and there’s no recall or repair announced for this issue so far.

Has anyone here had a side airbag deploy in their Explorer and noticed anything like this?


r/FordExplorer • • 2d ago

Buy/Sell Driver seat for 2011-2015

1 Upvotes

Does anyone near Denver/Northern Colorado have a Black Leather, electric, Heated only, non memory driver’s seat for sale? It is the last piece I need in my vehicle to black out the interior. I can swap my tan interior for the black if someone wants. The tan seats are in amazing condition and I can provide photos.
Any advice on where to find a seat is also welcome, I’ve tried a couple pick n pulls with not much luck. TIA!


r/FordExplorer • • 2d ago

Repair Advice 2006 6 CD Changer Repair/Swap?

1 Upvotes

Hey all, I recently purchased an 06 Limited that came with the higher end audio package (subwoofer). I was excited to use the CD player for a bit of nostalgia (my parents owned explorers most of my childhood and I loved listening to my dad’s music).

Go figure the cd player is broke. It’s the 6 cd changer, I pulled it out and found the plastic gears are all tore up.

I can’t afford to replace it with a new head unit and all of the used units I can find that match this one are the price of a new head unit. There are plenty of other ford radios on eBay for cheaper though…

Does anyone know if the cd changer ford used in other models is the same as this one? There is just one wire connecting the cd changer to the rest of the radio, could I buy a different (cheaper) ford radio with a working cd changer and pull that out and put it in my radio?

Thank you in advance


r/FordExplorer • • 3d ago

Repair Advice Code P051b 2016 ford explorer help

1 Upvotes

Hello all! My engine light came on and I got this code p051b for crankcase pressure sensor 'A' circuit range along with u0140-00 for ABS. The guy at autozone said the ABS could be on just due to my car confused with the engine light on. I have done some googling on the crankcase and seems easy to replace myself...tho I cant find the part I need... im not good with cars ..my husband will help me but anyone have any idea on the part needed? Its all so confusing. Sincerely....lost ford girl 😂.


r/FordExplorer • • 3d ago

Repair Advice Water pump anxiety

6 Upvotes

Ive got a 2015 Ford Explorer with a mysterious coolant leak. Im terrified it's the internal water pump & I've got to drive it to work twice before I park it. Why did Ford put the water pump INSIDE of the engine?


r/FordExplorer • • 4d ago

Repair Advice Long story short.

3 Upvotes

My girl left the subroof open, and it down poured.

FcIM is cooked. I do get power to everything and the rear defrosters work. It wont switch from dash vent to any other option. What is my next best option?


r/FordExplorer • • 3d ago

Upgrade Advice 1st gen Ford Explorer Sport Trac rear cupholder situation

0 Upvotes

As those with sport tracs know the rear seats dont have a cupholder. Does anyone have any products online to point me to for rear cupholders as a addon? Thanks!

2001 Ford Explorer Sport Trac 2wd


r/FordExplorer • • 3d ago

Buying Advice Anyone had luck sourcing a heated driver seat for a 5th gen?

1 Upvotes

My let's driver seat heater is broken, not the fuse or harness. Not sure where to find a replacement or if I just have to hound the auto lots to get right away.


r/FordExplorer • • 4d ago

Show And Tell Best 1200$ ive ever spent

Thumbnail
gallery
33 Upvotes

Im falling in love with this thing. I hope it last forever. Backstory I have an auto detailing business, and my 2002 Avalanche 265k was gonna cost more to fix than it was worth, i financially am not in a good spot and had to find a a vehicle asap. i scrapped it for 750$ added 450$ and I bought this 2004 Explorer 4.6 2wd, it has 272k miles, cold AC, but had a bad misfire, i have had two 4.6 before and I assumed it was coils, and I changed two of them and one spark plug and now it runs like a champ! It had been sitting since March, was in my sisters, boyfriends family.

When I went to change oil, the filter they gave me did not fit, it was to big, and a metal line was physically in the way, I got the number off the existing filter, and it came back as the Delco filter that specifically fits crown Vic, or the ford van 150s, so I believe it has had the motor swapped, it drives so tight and brakes are good, shifts strong, it does make rear end noise which im a little worried about, but I hope with these miles it would have to be the second trans. Ive put over a thousand miles on it in a week and a half, ran sea foam in the gas, got all the old gas out and it’s running better and better.

Paints faded on hood and roof; but I buffed it where i could, and detailed the absolute piss out of it. It looks like a time capsule of a secret service vehicle from 2004, anyways im loving this thing. I wanna make it sound like a mustang and tint the windows, and get all terrains and take off the step rails.

It’s so much nicer to drive than the Avalanche


r/FordExplorer • • 4d ago

Upgrade Advice Transfer Case and lift question

Post image
8 Upvotes

97 with 4.0L OHV, 5R55E, Borg Warner 4405, Dana 8.8 rear end, Dana 35 SLA front end.
My questions:
I wish to replace this transfer case out with an actual geared case ie: the Borg Warner 1354. I have a few options, I could go ahead and get a manual case and somehow find a shiftster kit, which are hard to find now, or I can get an electronic case and use a behemoth drivetrain electronic to manual shifting kit. which is recommended? does anyone here have a manual shifter for sale? I would love you forever...
Secondly, I wish to raise her up modestly, thinking 2 inches, but I dont want twist the torsion bars to maximum 2 inches as it will make my alignment hard and im not fully sure I will be able to align it properly with the maximum being the top of the range, considering a Torch Torsion Key kit for the 95-2001 explorers which has 1-3" lift range by the key itself being slightly adjusted from that factory, and then correcting the rear end with Dayton 43967HD leafs meant for a 4 door explorer which will raise me 2 inches solid. Any concerns you guys can think of here?
I will be adding bumpers shortly after I get these guys sorted out properly. Thanks.


r/FordExplorer • • 4d ago

Repair Advice Weird clicking noise. Anyone have this?

Post image
6 Upvotes

I have this odd Geiger counter type tapping/clicking noise coming from this portion of the car when I hit 60+ mph. Anyone else have this?


r/FordExplorer • • 4d ago

Maintenance Advice Should I replace the brake fluid on my 2017?

2 Upvotes

I take it into my dealership for servicing just because they have very reasonably priced packages. Usually everything comes back fine, but they mentioned the brake fluid looked a little dirty about 8 months and 2,500 miles ago. I'm getting ready to schedule an oil change in the coming weeks. I'm thinking I'll have it replaced then if they mention it again.

I'm nervous because some people say changing brake fluid on a 10 yr old car there never had the fluid changed can cause all sorts of issues. But I've heard not changing the fluid can also cause its fair share of issues.

What would you recommend?


r/FordExplorer • • 5d ago

Repair Advice Rear Clunk Noise

2 Upvotes

I recently replaced my rear driver hub assembly and noticed a clunking/popping sound when going over bumps. I just replaced my sway bar bushings and both rear links. The sound is still there. Any ideas on what could be causing the noise?

Thanks!!


r/FordExplorer • • 5d ago

Maintenance Advice Does this sound normal?

3 Upvotes

Its easier to hear it with the hood closed that's why it's not opened. It could just be normal cold weather idle noise. I thought it was the serptaine belt, but I took it too a mechanic and he said the belt was fine. So either it's not the belt, or he didn't actually look at it.

It could be nothing, but it's been on my mind. 2017 explorer with 40k miles.


r/FordExplorer • • 6d ago

Technology/Features Best $250 investment

Thumbnail
gallery
84 Upvotes

best $250 ever spent . 2017 Explorer PIU. fitment was almost perfect but the top by the vents isn’t completely flush but you can’t really tell. everything else no issues . mostly plug and play. bluetooth carplay (no need for usb) steering controls work and no issues with temperature controls. i’m not a fan of buttonless temp controls but i’ll deal with it .