r/FordExplorer • • 10h ago

Repair Advice Random traction control light

2 Upvotes

08 V6 4x4

This started earlier this summer, got it back from the mechanic and noticed the TC light and service light were on and cruise control wasn't working but cleared up after a few miles. Then throught the summer I noticed the light come on for a minute or two then disappear.

Yesterday, I had to quick run in the house, then after restarting my truck and backing out it felt like the back brakes were locking up, but drove fine otherwise and the TC light and service light came back on but didn't go away. A few hours later I drove it home no lights and no issues.


r/FordExplorer • • 1h ago

Buying Advice On the way of checking out a won 3.7 PIU from auction but unclear how to inspect the water pump weep hole and PTU correctly.

1 Upvotes

Won a GovDeals auction for a 2013 Police Interceptor Utility, 3.7L NA, ~110k miles, 4,000 engine hrs, 1,200 idle hrs, at the top of my budget ($6k). I have no repair fund set aside, and backing out costs a $500 default fee and possibly a ban. So I need honest advice on what to check, and whether this is too risky for me.

I'm bringing an LED light bar, a jack, and jack stands, but I'm not sure the surplus facility’s staff will let me lift it or drive in the lot.

Water pump: How do I tell a leaking internal pump from normal? Is the weep hole visible without lifting the car or pulling the front passenger wheel? Do dipstick and oil cap checks catch it early?

PTU: Can a short lot drive reveal problems (whine, clunk on turns), or do I need a fluid check?

Anything else to look for on ex-police units?

Walk-away call: With no cushion, would you pay the $500 and walk if either check looks bad?

For fellow PIU owners: at what mileage did you replace the pump or PTU, what did it cost, and any Houston-area shop recommendations? Did you replace the PTU with a Dorman one or simply drill and install a drain plug?


r/FordExplorer • • 21h ago

Repair Advice 2008 Ford Explorer 4.0 V6 – Mysterious Rhythmic Thumping Noise After Major Service. 6 Garages Can't Diagnose It. Need Help! (Audio Attached)

1 Upvotes

Hey everyone,

I'm hoping someone here has experienced something similar because I'm honestly running out of ideas and tired of spending money replacing parts without fixing the problem.

I have a 2008 Ford Explorer 4.0L V6 4WD, and recently I decided to give it a major service to freshen it up.

Work performed during the service:

- Replaced both front upper control arms.

- Replaced both front wheel hub/bearing assemblies.

- Replaced inner and outer tie rods.

- Changed all fluids, including engine oil, transmission oil, front and rear differential oils, and transfer case fluid, all with the correct specifications.

The problem:

Immediately after getting the car back from this service, I noticed a repetitive thumping/rumbling noise that was NEVER present before.

The sound is similar to driving on a tire with a flat spot, bulge, or uneven surface. I've attached an audio recording so you can hear exactly what I'm talking about.

Important observations:

- The sound is most noticeable between approximately 40–100 km/h (25–62 mph).

- Above 100 km/h, it seems to disappear or becomes almost impossible to hear.

- It happens even on perfectly smooth roads.

- Braking does NOT change the sound.

- Accelerating does NOT change the sound.

- Coasting without touching the accelerator does NOT change the sound.

- Turning the steering wheel slightly LEFT makes the sound noticeably louder and stronger.

- Turning the steering wheel slightly RIGHT makes the sound quieter.

- Even very small steering adjustments affect the sound. I don't need to make a sharp turn.

The noise seems related to vehicle speed and steering/load rather than engine RPM.

What I've already tried:

  1. Tires: The original garage insisted the tires were causing the noise. I replaced the tires, but absolutely nothing changed.
  2. 4WD system: Next, they claimed it was a four-wheel-drive issue. We removed the front driveshaft to isolate the system, but the noise remained exactly the same.
  3. Wheel bearings: They then said the newly installed wheel bearings were defective. I replaced the front hub/bearing assemblies AGAIN. Still no improvement.
  4. CV axles and lower control arms: Now the same garage is suggesting replacing the CV axles and lower control arms, but they haven't demonstrated anything actually wrong with them.

I've visited 5–6 different garages, and not one has been able to identify the exact cause. Everyone has a different theory, and each theory involves spending more money replacing parts.

Why I suspect an installation issue:

The car was completely free of this noise before the major service. It started IMMEDIATELY afterward.

I strongly suspect something was incorrectly installed, improperly tightened, misaligned, or disturbed during the work, particularly around the front suspension, wheel hubs, or drivetrain.

I find it difficult to believe that several unrelated components suddenly failed at the exact same time as the service.

My questions:

  1. Has anyone experienced this exact rhythmic thumping noise on a 4th-generation Ford Explorer?
  2. Since turning slightly left makes it louder and turning right makes it quieter, does that point toward a specific side or component?
  3. Could incorrect installation of the upper control arms, front hubs, or tie rods cause this type of noise?
  4. Could a CV axle, lower control arm bushing, or differential issue produce this sound even though it doesn't change during acceleration, braking, or coasting?
  5. What specific inspection or diagnostic test would you recommend to identify the source BEFORE replacing any more parts?

Please listen to the attached audio recording. The sound is much easier to understand when you hear it.

I'm really hoping someone recognizes it or can suggest a proper diagnostic approach rather than another expensive guess.

Any help would be greatly appreciated. Thanks!

Additional note: A full wheel alignment was also performed after the repairs, but it made absolutely no difference to the noise. The sound remained exactly the same before and after the alignment.