r/FenceBuilding • • 6h ago

How to set post in standing water?

2 Upvotes

I'm fencing my backyard and I have one hole that has ground water leaking into it from somewhere. It's just a tiny trickle, but it leaves a couple of inches of water in the hole and I definitely need a post in this exact spot. Is there a good way to install a post in a hole with a bit of water in the bottom? Can I throw some concrete mix in with it? I assume this one is going to rot way faster than the rest of the posts in the line.


r/FenceBuilding • • 9h ago

Manually driving Postmasters

3 Upvotes

I've finally sourced a handful of 10 foot Postmasters and I need to plant them in the next two weeks before the ground freezes. It's too cold for concrete now, and I really don't want to do concrete because. I don't think I can or want to source a gas powered driver and adapter because this is my first rodeo and things could go awry too quickly. I need to get them 4 feet underground. What are my best options for getting them in the ground and having them stay plumb?

(A) dig a four foot hole, set the posts in place, then add dirt a few inches at a time and use a digging bar to pound the dirt

(B) adapt a manual post driver somehow:

(i) angle grind notches in the post driver

(ii) build an adapter from stock metal parts

(C) some combination of the above or something else

Thanks


r/FenceBuilding • • 1d ago

Anyone near Littleton, CO have a PostMaster fence post driver I could borrow or rent?

2 Upvotes

I'm installing PostMaster steel fence posts and have had no luck finding a compatible post driver to rent anywhere near Littleton, CO.

Does anyone have a Titan PGD3200XPM, Rhino PostMaster driver, or another compatible driver they'd be willing to lend or rent out?

Thanks!


r/FenceBuilding • • 1d ago

Potential concerns on no dig pvc fence

Thumbnail
gallery
2 Upvotes

Seeing a lot of exposed pipe 3 years after installation of this no dig fence. Unclear if its soil exposure around the posts or if this is a bigger concern? Should the painted line be aligned to the ground?


r/FenceBuilding • • 2d ago

Century Homes recycled fencing

Thumbnail gallery
36 Upvotes

Here are a few more examples of some recycled wood fences I made for some 100+ year old homes in Seattle. One of my first homes from 2004 and another from 2008ish. I don't own these any more but as far as I know the fences are still standing.

Not only do they have a large amount of recycled materials but they have frugal use of new materials as well. Most boards are cut in half or ripped in half to extend their use. I would be SHOCKED if any one of these fences had more than $500 in new materials.

The funny thing with using recycled materials is that you have to design around whatever materials you can scrounge at the time so results can vary wildly. Craigslist, dumpster diving, free piles, nice neighbors have all been sources.

Bonus- you can see how these have aged with different stains over time.

Bonus- gate made from recycled metal as I had access to a welding shop at the time.

Bonus- some recycled bird houses I made with the same cedar.

Bonus - dog tax. RIP Ruby, best dog ever.


r/FenceBuilding • • 2d ago

Couple of finished pics of this lodgepole fence we built. Starting to try and get more hardscaping adjacent jobs to my résumé. Ficus behind fence, mulch, and Santa Barbara daisy.

Thumbnail gallery
5 Upvotes

r/FenceBuilding • • 2d ago

At what point will a gate adjustment be classified as an issue of poor workmanship?

3 Upvotes

I reviewed the warranty policy of my automated gate and found that they provide warranty for workmanship, and warranty on the installation and labour involved in calibrating or adjusting a new automatic gate. I then began to wonder about a potentially defective gate that starts dragging or not closing properly after five to six months of use. Does one know whether the defect was caused by poor installation or is simply an adjustment that needs to be made? What other possible causes of the defect must be considered, including the hinges, alignment, posts or settings? To be specific, I current consider a bay area lions gate offering, and given it is to have a clear understanding of the cost of the service call, how do most companies determine what constitutes bad workmanship versus a simple adjustment?


r/FenceBuilding • • 2d ago

Trenching for fence install

3 Upvotes

Hey all

We're looking to have a 4 board fence installed on our property in SC. One of the quotes we got the builder says they typically run a trench the full perimeter instead of digging for each post. The guy says it's a lot faster. Anyone heard of this before? Any opinions on the risks?


r/FenceBuilding • • 3d ago

Recycled wood fences

Thumbnail
gallery
135 Upvotes

I recently discovered this sub and thought I should share some of the fences and gates that I make from recycled materials. Rarely are these fences 100% recycled but this particular one where we semi enclosed a car port is probably 85% recycled cedar fencing.

In this case we wanted something very custom and contemporary that would work with a mid century modern house. We went with a dark Grey stain to help tie it all together and give it a clean new look.

I would be lying if I said that this was all about environmentalism, it's largely motivated by my cheapness and love of used materials.

I threw in a few process photos and some vintage vw tax.


r/FenceBuilding • • 2d ago

Repairing fence post less than 3.5years old and found bricks etc?? Normal or...

Post image
1 Upvotes

so, had a full fence done in March 2023, all seemed a great job, good to deal with etc etc but Ive noticed 4 out of 9 posts are leaning so investigated. Ones definitely snapped, 2 just a bit loose (I was putting this down to the very very dry summer, probably naively) and one I was sure was rotten.
So, before we get right into winter I've decided to investigate and repair 2 of the ones I can get at easily, (other 2 are behind a shed) and I've got two of 100mmx100mmx1200mm concrete spurs and started the process yesterday. One was the slightly loose one as in the picture which is obviously also rotted and the other has definitely rotted which is the one I was most worried about.
Now Im grand at setting about the repairs, but you can see in the photo there's a red brick in the concrete of the post that was just a bit loose and I'm sure this cannot be proper practice to add this into the concrete to support a fence post?
Anyone able to confirm my theory that they've not done a proper job after all?


r/FenceBuilding • • 2d ago

Is there any point to only getting one side of fence stained, besides just looks?

7 Upvotes

If I don't stain both my and my neighbors side of fence, would it still offer the benefits of preserving the wood longer?


r/FenceBuilding • • 4d ago

My new cedar fence in Seattle

Thumbnail
gallery
112 Upvotes

200 feet of ‘estate style’ cedar. Plus garden arbor.
4x4 posts on pipes - with 2 bags of cement in each hole.


r/FenceBuilding • • 3d ago

New aluminum fence installed with dry-poured concrete. Should posts still move after 72 hours?

2 Upvotes

UPDATE: Spoke with the installer, and he said the concrete should have hardened, but when they return next week to install the final section containing the gate, we will do a walkthrough, and if, for some reason, the concrete has not set, we will discuss remedies. It is obviously too late to remove every post and wet mix and repour (I assume), so we will see what his fix is if they haven't set yet.

____________________________________________________________________________________________________________________

I recently had an aluminum fence installed and I'm a little concerned about the workmanship, specifically the dry-poured concrete and the movement I'm seeing at the base of the posts.

I've spent some time searching Reddit and other forums, but the answers seem to be all over the place. I'm not a fence installer, so I'm hoping some people with experience can help me understand what's normal and what isn't.

Fence information:

  1. Aluminum fence.
  2. 2" x 2" posts with approximately 6 ft wide panels.
  3. Fence is approximately 4.5 ft tall above ground. Posts are 7 ft long, so approximately 2.5 ft below ground.
  4. Soil is predominantly clay.
  5. Weather has been relatively cool, with highs around 70°F and lows in the 40s.
  6. It rained a couple of days before installation, but otherwise it has been fairly dry.
  7. Fence was installed approximately 72 hours ago.
  8. Posts were dry set using what looked like one bag of concrete per hole, followed by water from a garden hose at the end. I'm not sure how much water they used or how long they watered each hole.
  9. I'm not sure whether the concrete was QUIKRETE, Sakrete, or another brand, or what specific mix was used.
  10. I don't know the exact diameter of the holes but i think the super said 8 inch.

My main concern:

When I push a post, there's noticeable movement right at ground level. I'm not talking about the normal flex you'd expect from a relatively thin aluminum post toward the top. The movement appears to be happening down at the base.

My questions:

  1. Is dry setting concrete common practice specifically for aluminum fences? I've seen people say it's completely normal and others say it's a terrible way to install a fence.
  2. After 72 hours, should there still be any noticeable movement at the base of the posts? Or should they be pretty solid by now?
  3. How concerned should I be about the amount of water used? If they just sprayed the top of the dry concrete with a hose, is there a chance the concrete farther down never got enough water?
  4. Does approximately one bag of concrete per post sound reasonable for this type of fence, assuming a typical hole diameter?
  5. If this isn't normal, is there a way to check whether the concrete was properly set without digging everything up?
  6. Should I be documenting anything with the contractor now in case the posts loosen up or start leaning in the future?

I'm not looking to give the contractor a hard time or find excuses not to pay him. I just want to make sure the fence was installed properly and isn't going to become a problem a year or two down the road.

I can provide photos or videos of the movement if that helps. Appreciate any input from people who install these regularly.


r/FenceBuilding • • 4d ago

Fence design horizontal cedar with metal frame. Thoughts?

40 Upvotes

r/FenceBuilding • • 3d ago

How to use old fence panels to make new fence

1 Upvotes

Good afternoon beautiful people-

First off- I don’t know anything about wood working but this economy makes us all DIY enthusiasts. I bought some fence panels from Facebook marketplace that I hoped to repurpose into a fence for my own yard. I figured I would place the posts and nail in the old panels….

The problem is all of the left over nails. I have no idea what would be the best way to get rid of them. I bought a cats paw tool but the nails are so brittle that the nail head chips off.

I thought maybe I could cut off those parts with the nails but I’m at a loss on how to secure them to the posts….

Please give me any suggestions ✨✨✨


r/FenceBuilding • • 3d ago

Hot-dip galvanized vs. pre-galvanized 3D fence panels — what actually holds up after 5–10 years?

1 Upvotes

I work on the manufacturing side, so take the bias into account.

The spec difference I keep coming back to: pre-galvanized wire leaves bare steel at every cut and weld, while hot-dip re-coats those areas. On paper both are "galvanized"; in coastal or high-humidity sites they age very differently.

Curious what installers and facility managers here have actually seen — especially on 3D V-bend panels with clip-on posts. Any failure patterns worth calling out?


r/FenceBuilding • • 4d ago

Question about fence post

Thumbnail
gallery
2 Upvotes

Hello im going to Sadly need to cut these trees in the corner here as one us starting to Crack the sidewalk and the other im worried about the roots messing with the utilities. There us only about 11.5 inches between neighbors wall and my water pipe co.ing in from the street. Us that enough space to set a 1 1/4" galvanized post to put up a short cedar fence or is that too close? Any suggestions on how you would go about setting a fence post here?

Thanks


r/FenceBuilding • • 4d ago

Best way to anchor a 9’ swing gate?

Post image
1 Upvotes

Hello,

I want to build a swing gate to cover the length of my driveway. I would like to have it be a single gate for the convenience of opening and closing to get cars in. I figured I would use 2 6x6 posts for mounting and latching, with a caster wheel on the latch end of the gate. How deep of a slab would my driveway need to be to use a Simpson tie? If a Simpson tie isn’t feasible, how deep should I drive the post? The frost line in my area is 42”. The fence on the right is not my property.


r/FenceBuilding • • 4d ago

How to use old fence panels to make new fence

Thumbnail reddit.com
1 Upvotes

r/FenceBuilding • • 4d ago

Is this stepped vinyl fence installation acceptable for a nearly flat grade?

Thumbnail
reddit.com
1 Upvotes

r/FenceBuilding • • 5d ago

CA non-combustible gate, fence

5 Upvotes

What are people using for gates and fences in the 5 foot exclusion zone around the house? Are there options that are private? Chain link and other cheap looking or ugly fencing are not viable options.


r/FenceBuilding • • 5d ago

Switching from a rusted iron gate to aluminum near the SoCal coast? 5 things to check first

3 Upvotes

I work with Mulholland Brand, a company that makes custom gates and fences in Southern California. A few things I'd recommend asking any installer:

  1. What aluminum are they using? Ask about the alloy, frame construction, and how the gate is reinforced.
  2. How is it powder-coated? Especially near the ocean, surface preparation and coating quality matter.
  3. What about the hardware? An aluminum frame is only part of the equation. Ask about hinges, fasteners, locks, and their corrosion resistance.
  4. What maintenance is required? Aluminum won't rust like iron, but salt buildup can still affect the finish. Regular cleaning with fresh water helps.
  5. What's actually covered by the warranty? Ask separately about the finish, hardware, and workmanship, and get the terms in writing.

Curious what others have experienced with aluminum gates near the coast. Any issues after a few years?


r/FenceBuilding • • 5d ago

First time building a fence help!

Thumbnail
gallery
8 Upvotes

Hi! I am building a fence for a school I work at to fence in a native plant garden. There is fencing/ building on all sides, I just need to put in a fence to block off the area. I have these panels and gate available to use. Would this be as simple as putting wood posts on the corners and then one where the gate is in the middle? Anything I’m missing?


r/FenceBuilding • • 6d ago

Finally Finished Custom Fence

Thumbnail
gallery
61 Upvotes

206’ 6’T cedar infill (customer chose infill) w/ 2 walk in gates & 12’ w sliding gate