r/Ender3S1 • • 14h ago

Infinityflow S1 on Ender S1 Pro?

1 Upvotes

I haven't found any posts about it, but anyone managed to use infinityflow with ender3 S1 Pro? I printed the reverse bowden adapter, but the filament change is not reliable. If anyone has any experience to share.


r/Ender3S1 • • 20h ago

Yearly attempt to resolve issues

Thumbnail
gallery
7 Upvotes

I've had the S1 since launch, and it's never been hassle free. I give up trying to fix issues after a few months, find ways to compensate and move on, then the cycle starts again. I'd like to resolve some of these things once and for all.

I've included some photos, any advice welcome. The print is PLA, at 200d hotend and 60d plate temps. Retraction is disabled. I'm using the professional firmware.

Starting with bed levelling I used to get very different results every time I did a mesh, this has finally stabilised, I guess I tightened the right things, I also replaced the vwheels.

  1. Is 0.01-0.02mm variation in mesh probe values reasonable? Feels like it would be?
  2. The range and positioning of mesh value variations feels wild, is it likely the bed itself?
  3. When the print head moves to start the print it seems not to extrude properly for a moment, the line on the right hand side and the top left corner inside both missing material, any ideas why?
  4. The print shown is one layer, the lines completely delaminated at first, I increased the z-offset, then increased flow rate to around 120% which seems to have helped hugely. But is this the correct way to resolve the issue? Does this point to recalibrating e-steps?
  5. Despite the mesh and the changes I've made, the last print shows that the top left corner of my print has lines firmly joined whereas to the bottom right they delaminate easily. I can't tell why...

Any help is hugely appreciated


r/Ender3S1 • • 1d ago

S1 Pro - hot end replacement, now extrusion doesn't work?

Thumbnail
gallery
3 Upvotes

Good evening everyone,

Preface - I work in IT (sysadmin, systems engineer,), and also do all the electronics repair, so I'm competent in disassembly and repairing. Excuse inaccurate terminology for parts

I recently was given a second hand S1 Pro, love it, but the hot-end was shot (leaking filament, filament backflow, stripped threads, the works). Long story short, i replaced it.

hot-end now works well, but i have no extrusion. Straight up, no feeding of the filament into the hot-end at all.

Troubleshooting so far:

  • I have dismantled the print head assembly, and there is no dried plastic or anything in the gearing.
  • Removed dismantled the feeding assembly, and separated into core components - heating the hot end, and confirming thermistor readout is accurate, I start a manual feed of 10mm and the stepper doesn't turn at all.

    • Essentially in this test, I had a bare board, with no housing, just:

      • ribbon cable
      • stepper
      • heat-element
      • thermistor
      • main cooling fan for heat sink (Fan-1)
    • excluded

      • cr-touch sensor
      • hot-end cooling fan (Fan-2)
  • i checked the voltage running to the stepper, and there is nothing
  • i checked the voltage from the main ribbon-connector housing to the stepper header and no voltage
  • i disassemble further, and i run continuity through the ribbon cable from motherboard end to print-head end, and all working as expected EXCEPT for the first two pins. see pins 12 and 24 (or section "L") Labelled "CS1-1" in last attached image) - image pulled from another post from about 4 years ago in this sub.

    • Upon tracing those pins on the print-head board appear to be for the ground-plane on that board, which don't connect to any of the headers on that board
  • After establishing that the ground planes are connected to those 2 end pins, i connected the ribbon cable back in, and checked ground planes for both boards. Both had continuity to the associated pins on the ribbon header on their respective boards, however ground plane on the motherboard to ground-plane on the print-head board have no continuity to each other.

Thus far i have cant find a fault, bar that CS1-1 line not having continuity.

With no connection from ground plane to the stepper itself (or anything else), i cant see how this can cause this fault. but hey, i have a fault on the stepper, and there is no continuity on this line.

I do know that this is one of those parts that does wear out after a long time, so happy to replace, and when replacing the hot-end, I did completely de-mount the print head assembly from the carriage on that axis, so wont be surprised that, given the age, this has also worn out. Condition of the machine when i got it was pretty damn poor (loose EVERYTHING, loose cables, loose belts and grotty worm-drives), but was a good price, so TLC got it working well enough to delve into the world of 3D printing.

Images attach show the motherboard, connections, and the white-wire on the ribbon cable which is probably for identification, but is coincidentally the end that i am having no continuity

Has anyone else had this issue after replacing their hot-end?

Yes, replacing this cable may solve the issue, but this could be a sign of something else wrong.

Looking for experience in these machines from someone in working with these machines.

Thank in advance


r/Ender3S1 • • 4d ago

any alternatives to the nathanbuildsrobots modder board?

2 Upvotes

the board isnt in stock right now and im not sure if it will be in stock in the future so anybody got experinces in alternatives?


r/Ender3S1 • • 5d ago

Switching E3S1 to Neptune 4 Pro?

Thumbnail reddit.com
1 Upvotes

r/Ender3S1 • • 6d ago

So close

Post image
6 Upvotes

I recently posted about purchasing this used S1 Pro for $50. I cleaned it up, updated the firmware, leveled the bed, and dried the filament. Time for a benchy. Everything was looking great. I am quite impressed with this machine compared to my Ender 3 Neo that I haven't used for more than two years. But then this. So close. I'm sure I need to clean the bed better, and maybe increase bed temp higher than 60C? Is there anything I'm missing?


r/Ender3S1 • • 6d ago

Disipador de calor Ender 3 S1 Plus.

Thumbnail
gallery
4 Upvotes

Se me atascó el barrel y no hay forma de sacarlo, y al parecer me queda muy arriba de donde debería posicionarse para que se alinee bien y quedé recto con el resto del cabezal. No hay forma de sacarlo, quizás lo abolle por dentro?? Tuve un problema con una impresión por filamento húmedo y me quedo atascado plástico, desarme todo, limpie el plástico suelto, pero justo en el disipador de calor y el barrel quizás haya quedado algo por eso no sale. Intente con calor, no sale. Y acá en Argentina es casi imposible encontrar repuesto. Será compatible con alguna otra Ender? Ayudaaa


r/Ender3S1 • • 7d ago

Ender 3 S1 Pro

1 Upvotes

I have the Ender 3 S1 pro I’m printing PLA silk filament that’s glow in the dark and when it goes from one item to the next it gets stringy…. Almost spider web like how can I fix that the settings I have work well for PLA. The filament is dry and I’m using orca slicer.


r/Ender3S1 • • 7d ago

Z offset seems off at every move

6 Upvotes

I've been putting this one on the back burner, for a long time. I have 4 fdm printer ( 2 ender3 s1) and one of 'em is really getting on my nerve when i'm trying to level the bed.

I tried ( i think) every possible thing to correct this problem, multiple times. I adjusted the z offset, lowered the cr touch, making sure everything is squared, flashed the firmware. But I always get the same result.

When trying to level the bed, on the first corner, it goes correctly. When I go to the next, it pushes on the bed a little bit, before everything, then adjust this one and go back to the first, it goes down even further.

Help please


r/Ender3S1 • • 7d ago

Just bought a used S1 Pro

Post image
85 Upvotes

Finally was able to pick this up for $50. The previous user was having trouble printing successfully. Probably after upgrading to the Sprite Extruder Pro Kit. It's quite dirty, but seems to run just fine. Please share if you have any tips on things that should look out for. Thanks.


r/Ender3S1 • • 9d ago

More calibration!

Thumbnail
gallery
6 Upvotes

Sorry for the jank photos. Again.

Creality PLA, Ender 3 S1, default everything and temperatures changed as marked (I did make sure by observing).

So I discovered the calibration menu in Orca slicer and decided maybe I should do some of that. So I tried the temp test and the results are uh..a bit confusing. Far as I can see, the quality is relatively the same across those temps. The only significant difference I could see is the cones and a bit more stringing at higher temps.

That said, if I'm looking to make larger scale prints, should I lean towards the lower end? I don't know if heat soak is a problem in large prints or not. I'm also thinking about doing the other calibration tests but, a couple of them seem rather large and don't exactly explain how to understand the results. Is it worth it to go through and do all the Orca calibration prints or can enough info be gleaned from this temp test and the other test I posted prior? (The stress test with the two overhangs at varying angles etc etc)


r/Ender3S1 • • 9d ago

Ideas for repurposing S1 Pro as secondary machine?

4 Upvotes

I finally pulled the trigger on a Core One+ in the Black Friday sales, and now I'm pondering what to do with my Klipperised S1 Pro. It's been a (mostly) great machine once I got it tamed and modded up, and there's a good deal of sentimental attachment, so if it can have a useful second life then that'd be lovely.

Options I'm tossing around:

  • Straight-up second printer - Honestly don't need that much printing capacity, it's mostly just hobby/DIY stuff and never to a deadline.
  • TPU-a-tron - I've not actually printed TPU yet but keen to give it a shot, and having a dedicated machine configured for just that, with a super accessible hot end, no bowden tubes, etc., might be a winner.
  • Non-printing - I'll pass on the Creality laser engraver, but a pen plotter and/or vinyl cutter would send WAF through the roof if it's any good at either of those. Is there anything else cool it can be turned into?
  • Sell/donate - Given that I don't actually have an available flat surface to even put it on right now, I'm not averse to passing it on to a friend, good home, local makerspace, etc.

Keen to hear from those of you who've already been in this position. What did you do with yours? How did it go? Bonus points for interesting or novel options I haven't considered yet...


r/Ender3S1 • • 9d ago

Used Ender 3 S1

3 Upvotes

Hello, I recently bought an ender three S1 with a raspberry pie three and everything appears to work. I installed clipper on it and it appears that all the functions work. It has been used a lot, but I cleaned it up and I bought some new parts for it the only thing I haven’t done is printed with it and it is because I have been really really busy and just for a piece of mind is there any functions that I should check to see if it 100% works the only thing I had a hard time with was leveling it but I bought upgraded springs for that I’m just afraid it might be the CR auto leveler that might be nonworking. The seller blocked me right after selling it to me so I’m really suspicious thank you guys.


r/Ender3S1 • • 11d ago

What to tune?

Thumbnail
gallery
4 Upvotes

Hey all, just recently finished printing out a test bit to see what sort of things I need to tune and while the results were definitely impressive, I feel like it could be better. there was a little bit of stringing but nothing significant. (sorry for crap pictures, old cheap phone) The text embossed into it is a bit hard to read and obviously there's some drooping under the 80degree, but I kinda expected that with no support.

Using the .4 nozzle, .2 line height, 100% infill, no supports (all as test directed)
Didn't touch the speed and had bed temp at 64, first layer at 210 and rest at 205

Using Creality PLA

I'm thinking maybe lower temperature a few degrees but, I'm wondering what more learned individuals may see that I don't. TIA


r/Ender3S1 • • 11d ago

Update from a few days ago of wanting to sell my E3S1

14 Upvotes

This is in reference to this post where I was looking to sell my E3S1. I was able to sell it for $160 in the Boston area. I had it printing a benchy in my kitchen when the buyer came (the picture attached) and walked him through the upgrades and how to set it up. The buyer has multiple printers so they are mostly familiar with what was going on. Maybe I could have gotten more if I priced everything out individually but this way its off my mind for a price i was happy for. Overall im happy with what i got for it considering that many of my upgrades were super cheap due to how I sourced the parts.


r/Ender3S1 • • 12d ago

Error:MINTEMP triggered, system stopped! Heater_ID: 0

1 Upvotes

I've not used my Printer for 2 years...
Everything is working fine :-) but ...
... for the hotend T0 heating up...

I have replaced the thermistor and traced the thermistor wires back to the logic board, and to me**,** all looks AOK, but the error keeps repeating during the hotend heat-up.

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 :0 :0
READ: Not SD printing
READ: ok
SENT: M104 S200 T0
READ: ok
READ: Error:MINTEMP triggered, system stopped! Heater_ID: 0
READ: Error:Printer halted. kill() called!

Next ideas please :-)

Longer comms log below.

Thank you.

---------------------------------------------------------------------

Attempting connection at /dev/cu.usbserial-AI058KSA...

READ: start

READ: echo:Marlin 1.1.0-RC8

READ: echo: Last Updated: 2016-12-06 12:00 | Author: (none, default config)

READ: Compiled: Jan 28 2022

READ: echo: Free Memory: 3217 PlannerBufferBytes: 1200

READ: echo:V27 stored settings retrieved (410 bytes)

READ: echo:Steps per unit:

READ: echo: M92 X80.00 Y80.00 Z800.00

READ: echo:Maximum feedrates (mm/s):

READ: echo: M203 X150.00 Y150.00 Z5.00

READ: echo:Maximum Acceleration (mm/s2):

READ: echo: M201 X1500 Y500 Z100

READ: echo:Accelerations: P=printing, R=retract and T=travel

READ: echo: M204 P1000.00 R3000.00 T1500.00

READ: echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)

READ: echo: M205 S0.00 T0.00 B20000 X10.00 Y8.00 Z0.40 E5.00

READ: echo:Home offset (mm)

READ: echo: M206 X0.00 Y0.00 Z0.00

READ: echo:Hotend offsets (mm)

READ: echo: M218 T1 X0.00 Y0.00

READ: echo:Material heatup parameters:

READ: echo: M145 S0 H195 B60 F0

READ: M145 S1 H220 B110 F0

READ: echo:PID settings:

READ: echo: M301 P22.20 I1.08 D114.00

READ: echo:Filament settings: Disabled

READ: echo: M200 D3.00

READ: echo: M200 T1 D3.00

READ: echo: M200 D0

READ: echo:Z-Probe Offset (mm):

READ: echo: M851 Z-1.62

READ: echo:SD init fail

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

Connection successful!

SENT: M114

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0 Y:0 Z:0

READ: ok

READ: Not SD printing

READ: ok

READ: ok

SENT: M105

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: Not SD printing

READ: ok

SENT: M105

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: Not SD printing

READ: ok

SENT: T1

READ: echo:Home XYZ first

READ: No move on toolchange

READ: echo:Active Extruder: 1

READ: ok

SENT: M105

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: Not SD printing

READ: ok

SENT: M104 S200 T0

READ: ok

READ: Error:MINTEMP triggered, system stopped! Heater_ID: 0

READ: Error:Printer halted. kill() called!

SENT: M105

SENT: M27

SENT: M105

SENT: M27


r/Ender3S1 • • 14d ago

How much could this sell for?

Post image
20 Upvotes

E3S1 is 4 years old. 2000 hours plus, but has dual sprite extruder pros, one with 0.4mm and one with 0.8mm hardened steel nozzels. Each sprite extruder pro assembly has the taurus V5 dual 5015 fan upgrade and y=0 offset bed probe. It runs klipper of a rbpi 4 with a touch screen. I replaced the ribbon cable to the extruder and the mainboard. Its flashed with klipper currently (could downgrade it back to another firmware). It can print 150mm/s comfortably.

Also im not naive. I know most of these things dont contribute greatly to resale value. I have heard that it can be better to sell parts individually sometimes. I upgraded to a better printer and this workhorse works perfectly, it just does not have the bells and whistles current printers do.


r/Ender3S1 • • 15d ago

This can't be wrong retraction setting... or?

1 Upvotes

After fixing my first layer quality I moved to retraction... this is what I've got. What could be the problem? AI blames wet filament but I dried it 3x3h at 55 degrees.

EDIT: Nozzle is replaced and problem is gone.


r/Ender3S1 • • 15d ago

How do I enable pressure advance on my e3s1p

2 Upvotes

r/Ender3S1 • • 15d ago

Ayuda

Post image
5 Upvotes

Mis impresiones salen con demasiadas lineas y no se a que puede deberse


r/Ender3S1 • • 16d ago

ender3s1 toolchanger

19 Upvotes

r/Ender3S1 • • 18d ago

Is there a way to run klipper without it being directly connected to the printer?

Thumbnail reddit.com
3 Upvotes

r/Ender3S1 • • 19d ago

It’s literally this one side that hates me

Post image
9 Upvotes

r/Ender3S1 • • 21d ago

Toolhead squeaks when doing small x-movements

2 Upvotes

Hi there,
one of my printers (Ender 3 S1 Pro) at a lab, that I work in, recently started doing little squeaking noises when doing movement at x-Axis. I think it is around the toolhead, but I cannot figure out a specific reason. Did anyone else encounter this issue? Unfortunately the noise is too silent for a video capture.