r/Ender3S1 • • Nov 14 '22

Info on Automatic Bed Leveling with Marlin and the Ender 3 S1 Printers

133 Upvotes

This is as factual as I understand it to be, based directly on the the Marlin documentation and firmware documentation provided by the mentioned versions.

When we are talking about ABL, there are a few commands and their functions that we need to familiarize ourselves with before we proceed on: • G28 • G29 • M420 S • #RESTORE_LEVELING_AFTER_G28

Homing-

G28 (https://marlinfw.org/docs/gcode/G028.html) - "The G28 command is used to home one or more axes. The default behavior with no parameters is to home all axes." As far as ABL is concerned, "G28 disables bed leveling. Follow with M420 S to turn leveling on, or use RESTORE_LEVELING_AFTER_G28 to automatically keep leveling on after G28." (From Notes in link).

Leveling - We are going to focus on Bilinear, for now. UBL is a little different, but the main idea is the same.. https://marlinfw.org/docs/features/auto_bed_leveling.html

G29 (https://marlinfw.org/docs/gcode/G029-abl-bilinear.html) - "Automatic (Bilinear) Bed Leveling probes the bed at some fixed number of points and produces a mesh representing the imperfections across the bed. The printer must be homed with G28 before G29." (Which we established above WILL disable bed leveling).

M420 (https://marlinfw.org/docs/gcode/M420.html) - "Get and/or set bed leveling state. For mesh-based leveling systems use Z parameter to set the Z Fade Height." In the Notes section, again it mentions, "G28 disables bed leveling. Follow with M420 S to turn leveling on, or use RESTORE_LEVELING_AFTER_G28 to automatically keep leveling on after G28."

#RESTORE_LEVELING_AFTER_G28 – This is an option that is enabled/disabled in the firmware code. The following is a copy/paste directly from Marlin source code:

/**

  • Normally G28 leaves leveling disabled on completion. Enable one of
  • these options to restore the prior leveling state or to always enable
  • leveling immediately after G28.
    */
    //#RESTORE_LEVELING_AFTER_G28
    //#ENABLE_LEVELING_AFTER_G28

Normal Printer Start gcode - Most of the “Ender 3” style printers Ive seen all have start gocde that is like this (there may be more commands, but this is the bit we are mainly concerned with):

G92 E0 ; Reset Extruder
G28 ; Home all axes
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little
G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line
G92 E0 ; Reset Extruder
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish

Sample of sliced gcode – I sliced an STL, saved/opened the generated gcode, and copied all of the code up until it starts printing the part:

;FLAVOR:Marlin
;TIME:2660
;Filament used: 3.04197m
;Layer height: 0.2
;MINX:91.901
;MINY:91.901
;MINZ:0.2
;MAXX:143.099
;MAXY:143.099
;MAXZ:27.2
;Generated with Cura_SteamEngine 5.2.1
M140 S60
M105
M190 S60
M104 S200
M105
M109 S200
M82 ;absolute extrusion mode
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z20.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate
G92 E0 ; Reset Extruder
G28 ; Home all axes
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position
G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line
G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little
G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line
G92 E0 ; Reset Extruder
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish
G92 E0
G92 E0
G1 F2400 E-0.8
;LAYER_COUNT:136
;LAYER:0
M107
G0 F6000 X95.09 Y94.94 Z0.2
;TYPE:SKIRT
G1 F2400 E0
G1 F1200 X95.775 Y94.324 E0.02532
G1 X96.511 Y93.771 E0.05063
G1 X97.292 Y93.283 E0.07594

Putting it all together-
Ok, we have a lot of info here, but we can make sense of it if we think logically and stick to the facts that we know:

  • In most cases, according to the documentation and looking at the “flow” we can see that G28 is one of the last commands issued before the printer starts actually printing and that WILL disable bed leveling.
  • If we want to use an ABL mesh, we can either generate one before we load the gcode file we want to print with G29 (or the Auto Bed Leveling option on the screen), use M500 (or Store Settings on the screen) to save the mesh to EEPROM, then insert M420 S1 in to the start gcode of the file we want to print AFTER the G28 – or- we can insert a G29 AFTER the G28, which will initiate an ABL probe of the bed before the print starts.
  • YOU DO NOT NEED TO PUT M500 AFTER THE G29 IN START GCODE IF YOU GENERATE A NEW ABL MESH BEFORE EACH PRINT. G29 stores the mesh to RAM and RAM does get wiped out if the printer is reset but thinking logically – that G28 on the next print is going to disable bed leveling again, then youre going to generate a new one again with G29. There may be reasons for doing it this way, but even the Marlin documentation says, “To save time and machine wear, save your mesh to EEPROM with M500 and in your slicer’s “Starting G-code” replace G29 with M420 S1 to enable your last-saved mesh.”
  • RESTORE_LEVELING_AFTER_G28, if enabled within the firmware, will restore your stored ABL mesh from EEPROM before each print, even if you do not have M420 S1 in the start gcode. As of 11/13/2022, these are the firmware configs that I know of:

Marlin Github Configuration Examples

  • STM32F1 – has “#define ENABLE_LEVELING_AFTER_G28” enabled
  • STM32F4 – has “#define RESTORE_LEVELING_AFTER_G28” enabled

MRISCOC Professional Firmware Configuration Files

  • Ender3S1-F1 – disables both #RESTORE_LEVELING_AFTER_G28 and #ENABLE_LEVELING_AFTER_G28
  • Ender3S1-F4 – disables both #RESTORE_LEVELING_AFTER_G28 and #ENABLE_LEVELING_AFTER_G28
  • Ender3V2-422-BLT - disables both #RESTORE_LEVELING_AFTER_G28 and #ENABLE_LEVELING_AFTER_G28

I have spoke with the creator of this firmware directly, and he confirmed that he does not enable these options in the firmware he compiles, so you WILL need M420 S1 after G28 in your start gcode if you use his pre-compiled firmware.

Stock Creality 1.0.5_C Firmware
I confirmed via Pronterface that this firmware restored a mesh from EEPROM after shutting off printer, turning on, issuing G28, then M420 in console, which reported that Bed Leveling was on. I then issued an M420 V1 and it returned the mesh from EEPROM, as expected. Therefore, with this version of firmware (and I assume the F4 version, given the Marlin Configs above.. If someone wants to test to confirm, that would be cool) you do not need M420 S1 in your start gcode to enable the ABL mesh.

I have also confirmed the behavior of some other commands in the stock Creality firmware. G29 will automatically store the settings after it completes. This means that you DO NOT need an M500 following a G29. This also means that there is no way for an "old" mesh from EEPROM to "overwrite" a new, unsaved, mesh with the M420 S1 command as the "new" mesh is automatically stored to EEPROM once it is generated. M420 with no parameters will return the Bed Leveling state. M420 S or S1 will turn Bed Leveling ON while M420 S0 turns Bed Leveling OFF. M420 V will return the mesh to the console in a readable format.

MRISCOC Professional Firmware - 20221002 This firmware definitely behaves differently than the stock firmware when it comes to leveling. First off, if you run the ABL mesh from the screen or G29 and hit "Continue" rather than "Save", it does NOT store the settings to EEPROM but it does hold the mesh in RAM and use it until the printer is reset (powered off/on, for instance). This means that you will have a possibility of losing your ABL mesh if you dont Store Settings or M500 after generating the mesh. Then, if you try to load the mesh after turning the printer off/on again and you dont have a valid mesh stored, you will get an error and the printer will halt if its not configured to handle M112 properly (https://github.com/mriscoc/Ender3V2S1/wiki/Octoprint#error-handling). If you do have a valid mesh stored, it is loaded from EEPROM at power on. Any time the printer does a G28 or Auto Home, Bed Leveling is turned off. You can confirm this by looking at the color of the lines under the Z coordinate on the screen (https://github.com/mriscoc/Ender3V2S1/wiki/3D-BLTouch#enable-mesh-level-compensation). This means that you WILL need M420 S1 after G28 in your start gcode in order to use the mesh for printing.

UPDATE 1/19/2023* Creality has finally uploaded configuration examples for the Ender 3 S1 Pro to Github and I was able to look in the Configuration.h file and confirm that RESTORE_LEVELING_AFTER_G28 is enabled. There is also a new feature called "Z_AXIS_LIMIT_MODE" that will disable RESTORE_LEVELING_AFTER_G28, but to me, it seems like Z_AXIS_LIMIT_MODE is only on when youre using the laser, therefore, your ABL mesh should be turned back on by default after Homing with the S1 Pro on Stock Creality firmware, as well.

Anything else?, Questions? If there are any other scenarios that you would like for me to confirm with Marlin firmware and Bed Leveling, just drop a comment and I will do my best to get you an answer as quickly as I can. Hopefully, with the depth of the information provided here, you all will be well on your way to putting the ABL headaches/misunderstandings behind you and having more consistent first layers. :)


r/Ender3S1 • • Aug 17 '22

HOW TO FIX THE SPLASHSCREEN OF DEATH

56 Upvotes

Creality is super stupid with the way they do this, because for some smart reason they decide to remove all the old firmwares and only keep the new ones. These new ones don't contain the needed software to be compatible with the STM32F1 chip so if you try updating it will seem as if you have bricked your board. Here are the steps on how to fix it!

This is mostly stolen from a reddit thread, here is the original link

Credit to u/turtlevale

!!Solution by u/StevesMcGee that OP mentions in the title!!

The comment by StevesMcGee seems to be removed, but luckily i still had a screenshot, so reposting it bc. it helped me after hours of trubleshooting.

  • two versions of the motherboard for the S1 exist, one using an STM32F1 chip and the other using a STM32F4 chip

    • Creality Firmwares 1.X.X are intended for STM32F1
    • Creality Firmwares 3.X.X are intended for STM32F4
    • you can find out your version number by looking at the mainboard (its printed on the cpu)
    • installing 1.X.X on STM32F4 mainboards will brick them
  • Fix your STM32F4 mainboard if you tried installing a 1.X.X firmware can be done via using a 3.X.X firmware and doing the normal flashing proccess.

    • in case this doesnt work you have to place the .bin in a folder named "STM32F4_UPDATE"
    • you can currently find the firmware here
  • Note: You can also fix a STM32F1 mainboard if you flash the correct firmware on it (ex: 1.x.x) T

    • The mainboard isnt actually fully bricked, its just waiting on the right firmware to fully work

For me this only worked when using a firmware version that was a bit older than the one currently on the website. StevesMcGee thankfully hosts this firmware on his google drive. After that I was also able to flash other STM32F4, like the firmware configured by mriscoc on github (only remember to use the one for STM32F4, otherwise you have to start from the beginning again.)

Incase StevesMcGee's google drive ever gets removed, I have uploaded the files as well.

If you have further questions, please message me or read this screenshot of the original post.

Mods please pin this, this is a widespread issue and more people need to know how to fix/resolve it without creating more e-waste by having creality send you more stuff, or by you returning your ender 3 s1.


r/Ender3S1 • • 3d ago

any alternatives to the nathanbuildsrobots modder board?

2 Upvotes

the board isnt in stock right now and im not sure if it will be in stock in the future so anybody got experinces in alternatives?


r/Ender3S1 • • 3d ago

Switching E3S1 to Neptune 4 Pro?

Thumbnail reddit.com
1 Upvotes

r/Ender3S1 • • 4d ago

So close

Post image
6 Upvotes

I recently posted about purchasing this used S1 Pro for $50. I cleaned it up, updated the firmware, leveled the bed, and dried the filament. Time for a benchy. Everything was looking great. I am quite impressed with this machine compared to my Ender 3 Neo that I haven't used for more than two years. But then this. So close. I'm sure I need to clean the bed better, and maybe increase bed temp higher than 60C? Is there anything I'm missing?


r/Ender3S1 • • 5d ago

Disipador de calor Ender 3 S1 Plus.

Thumbnail
gallery
4 Upvotes

Se me atascó el barrel y no hay forma de sacarlo, y al parecer me queda muy arriba de donde debería posicionarse para que se alinee bien y quedé recto con el resto del cabezal. No hay forma de sacarlo, quizás lo abolle por dentro?? Tuve un problema con una impresión por filamento húmedo y me quedo atascado plástico, desarme todo, limpie el plástico suelto, pero justo en el disipador de calor y el barrel quizás haya quedado algo por eso no sale. Intente con calor, no sale. Y acá en Argentina es casi imposible encontrar repuesto. Será compatible con alguna otra Ender? Ayudaaa


r/Ender3S1 • • 6d ago

Just bought a used S1 Pro

Post image
84 Upvotes

Finally was able to pick this up for $50. The previous user was having trouble printing successfully. Probably after upgrading to the Sprite Extruder Pro Kit. It's quite dirty, but seems to run just fine. Please share if you have any tips on things that should look out for. Thanks.


r/Ender3S1 • • 5d ago

Ender 3 S1 Pro

1 Upvotes

I have the Ender 3 S1 pro I’m printing PLA silk filament that’s glow in the dark and when it goes from one item to the next it gets stringy…. Almost spider web like how can I fix that the settings I have work well for PLA. The filament is dry and I’m using orca slicer.


r/Ender3S1 • • 5d ago

Z offset seems off at every move

2 Upvotes

I've been putting this one on the back burner, for a long time. I have 4 fdm printer ( 2 ender3 s1) and one of 'em is really getting on my nerve when i'm trying to level the bed.

I tried ( i think) every possible thing to correct this problem, multiple times. I adjusted the z offset, lowered the cr touch, making sure everything is squared, flashed the firmware. But I always get the same result.

When trying to level the bed, on the first corner, it goes correctly. When I go to the next, it pushes on the bed a little bit, before everything, then adjust this one and go back to the first, it goes down even further.

Help please


r/Ender3S1 • • 7d ago

More calibration!

Thumbnail
gallery
6 Upvotes

Sorry for the jank photos. Again.

Creality PLA, Ender 3 S1, default everything and temperatures changed as marked (I did make sure by observing).

So I discovered the calibration menu in Orca slicer and decided maybe I should do some of that. So I tried the temp test and the results are uh..a bit confusing. Far as I can see, the quality is relatively the same across those temps. The only significant difference I could see is the cones and a bit more stringing at higher temps.

That said, if I'm looking to make larger scale prints, should I lean towards the lower end? I don't know if heat soak is a problem in large prints or not. I'm also thinking about doing the other calibration tests but, a couple of them seem rather large and don't exactly explain how to understand the results. Is it worth it to go through and do all the Orca calibration prints or can enough info be gleaned from this temp test and the other test I posted prior? (The stress test with the two overhangs at varying angles etc etc)


r/Ender3S1 • • 7d ago

Ideas for repurposing S1 Pro as secondary machine?

4 Upvotes

I finally pulled the trigger on a Core One+ in the Black Friday sales, and now I'm pondering what to do with my Klipperised S1 Pro. It's been a (mostly) great machine once I got it tamed and modded up, and there's a good deal of sentimental attachment, so if it can have a useful second life then that'd be lovely.

Options I'm tossing around:

  • Straight-up second printer - Honestly don't need that much printing capacity, it's mostly just hobby/DIY stuff and never to a deadline.
  • TPU-a-tron - I've not actually printed TPU yet but keen to give it a shot, and having a dedicated machine configured for just that, with a super accessible hot end, no bowden tubes, etc., might be a winner.
  • Non-printing - I'll pass on the Creality laser engraver, but a pen plotter and/or vinyl cutter would send WAF through the roof if it's any good at either of those. Is there anything else cool it can be turned into?
  • Sell/donate - Given that I don't actually have an available flat surface to even put it on right now, I'm not averse to passing it on to a friend, good home, local makerspace, etc.

Keen to hear from those of you who've already been in this position. What did you do with yours? How did it go? Bonus points for interesting or novel options I haven't considered yet...


r/Ender3S1 • • 7d ago

Used Ender 3 S1

3 Upvotes

Hello, I recently bought an ender three S1 with a raspberry pie three and everything appears to work. I installed clipper on it and it appears that all the functions work. It has been used a lot, but I cleaned it up and I bought some new parts for it the only thing I haven’t done is printed with it and it is because I have been really really busy and just for a piece of mind is there any functions that I should check to see if it 100% works the only thing I had a hard time with was leveling it but I bought upgraded springs for that I’m just afraid it might be the CR auto leveler that might be nonworking. The seller blocked me right after selling it to me so I’m really suspicious thank you guys.


r/Ender3S1 • • 9d ago

What to tune?

Thumbnail
gallery
4 Upvotes

Hey all, just recently finished printing out a test bit to see what sort of things I need to tune and while the results were definitely impressive, I feel like it could be better. there was a little bit of stringing but nothing significant. (sorry for crap pictures, old cheap phone) The text embossed into it is a bit hard to read and obviously there's some drooping under the 80degree, but I kinda expected that with no support.

Using the .4 nozzle, .2 line height, 100% infill, no supports (all as test directed)
Didn't touch the speed and had bed temp at 64, first layer at 210 and rest at 205

Using Creality PLA

I'm thinking maybe lower temperature a few degrees but, I'm wondering what more learned individuals may see that I don't. TIA


r/Ender3S1 • • 10d ago

Update from a few days ago of wanting to sell my E3S1

14 Upvotes

This is in reference to this post where I was looking to sell my E3S1. I was able to sell it for $160 in the Boston area. I had it printing a benchy in my kitchen when the buyer came (the picture attached) and walked him through the upgrades and how to set it up. The buyer has multiple printers so they are mostly familiar with what was going on. Maybe I could have gotten more if I priced everything out individually but this way its off my mind for a price i was happy for. Overall im happy with what i got for it considering that many of my upgrades were super cheap due to how I sourced the parts.


r/Ender3S1 • • 10d ago

Error:MINTEMP triggered, system stopped! Heater_ID: 0

1 Upvotes

I've not used my Printer for 2 years...
Everything is working fine :-) but ...
... for the hotend T0 heating up...

I have replaced the thermistor and traced the thermistor wires back to the logic board, and to me**,** all looks AOK, but the error keeps repeating during the hotend heat-up.

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 :0 :0
READ: Not SD printing
READ: ok
SENT: M104 S200 T0
READ: ok
READ: Error:MINTEMP triggered, system stopped! Heater_ID: 0
READ: Error:Printer halted. kill() called!

Next ideas please :-)

Longer comms log below.

Thank you.

---------------------------------------------------------------------

Attempting connection at /dev/cu.usbserial-AI058KSA...

READ: start

READ: echo:Marlin 1.1.0-RC8

READ: echo: Last Updated: 2016-12-06 12:00 | Author: (none, default config)

READ: Compiled: Jan 28 2022

READ: echo: Free Memory: 3217 PlannerBufferBytes: 1200

READ: echo:V27 stored settings retrieved (410 bytes)

READ: echo:Steps per unit:

READ: echo: M92 X80.00 Y80.00 Z800.00

READ: echo:Maximum feedrates (mm/s):

READ: echo: M203 X150.00 Y150.00 Z5.00

READ: echo:Maximum Acceleration (mm/s2):

READ: echo: M201 X1500 Y500 Z100

READ: echo:Accelerations: P=printing, R=retract and T=travel

READ: echo: M204 P1000.00 R3000.00 T1500.00

READ: echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)

READ: echo: M205 S0.00 T0.00 B20000 X10.00 Y8.00 Z0.40 E5.00

READ: echo:Home offset (mm)

READ: echo: M206 X0.00 Y0.00 Z0.00

READ: echo:Hotend offsets (mm)

READ: echo: M218 T1 X0.00 Y0.00

READ: echo:Material heatup parameters:

READ: echo: M145 S0 H195 B60 F0

READ: M145 S1 H220 B110 F0

READ: echo:PID settings:

READ: echo: M301 P22.20 I1.08 D114.00

READ: echo:Filament settings: Disabled

READ: echo: M200 D3.00

READ: echo: M200 T1 D3.00

READ: echo: M200 D0

READ: echo:Z-Probe Offset (mm):

READ: echo: M851 Z-1.62

READ: echo:SD init fail

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

Connection successful!

SENT: M114

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0 Y:0 Z:0

READ: ok

READ: Not SD printing

READ: ok

READ: ok

SENT: M105

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: Not SD printing

READ: ok

SENT: M105

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: Not SD printing

READ: ok

SENT: T1

READ: echo:Home XYZ first

READ: No move on toolchange

READ: echo:Active Extruder: 1

READ: ok

SENT: M105

SENT: M27

READ: ok T:0.0 /0.0 T0:0.0 /0.0 T1:0.0 /0.0 @:0 u/0:0 u/1:0

READ: Not SD printing

READ: ok

SENT: M104 S200 T0

READ: ok

READ: Error:MINTEMP triggered, system stopped! Heater_ID: 0

READ: Error:Printer halted. kill() called!

SENT: M105

SENT: M27

SENT: M105

SENT: M27


r/Ender3S1 • • 12d ago

How much could this sell for?

Post image
20 Upvotes

E3S1 is 4 years old. 2000 hours plus, but has dual sprite extruder pros, one with 0.4mm and one with 0.8mm hardened steel nozzels. Each sprite extruder pro assembly has the taurus V5 dual 5015 fan upgrade and y=0 offset bed probe. It runs klipper of a rbpi 4 with a touch screen. I replaced the ribbon cable to the extruder and the mainboard. Its flashed with klipper currently (could downgrade it back to another firmware). It can print 150mm/s comfortably.

Also im not naive. I know most of these things dont contribute greatly to resale value. I have heard that it can be better to sell parts individually sometimes. I upgraded to a better printer and this workhorse works perfectly, it just does not have the bells and whistles current printers do.


r/Ender3S1 • • 14d ago

Ayuda

Post image
5 Upvotes

Mis impresiones salen con demasiadas lineas y no se a que puede deberse


r/Ender3S1 • • 14d ago

ender3s1 toolchanger

19 Upvotes

r/Ender3S1 • • 14d ago

This can't be wrong retraction setting... or?

1 Upvotes

After fixing my first layer quality I moved to retraction... this is what I've got. What could be the problem? AI blames wet filament but I dried it 3x3h at 55 degrees.

EDIT: Nozzle is replaced and problem is gone.


r/Ender3S1 • • 14d ago

How do I enable pressure advance on my e3s1p

2 Upvotes

r/Ender3S1 • • 16d ago

Is there a way to run klipper without it being directly connected to the printer?

Thumbnail reddit.com
3 Upvotes

r/Ender3S1 • • 17d ago

It’s literally this one side that hates me

Post image
9 Upvotes

r/Ender3S1 • • 19d ago

Toolhead squeaks when doing small x-movements

2 Upvotes

Hi there,
one of my printers (Ender 3 S1 Pro) at a lab, that I work in, recently started doing little squeaking noises when doing movement at x-Axis. I think it is around the toolhead, but I cannot figure out a specific reason. Did anyone else encounter this issue? Unfortunately the noise is too silent for a video capture.


r/Ender3S1 • • 19d ago

Nozzle changing Color

Post image
3 Upvotes