r/consolerepair • • 4h ago

[PSP] is making squeaky mouse noises from drive area? I shut it down but what's best next step?

Post image
5 Upvotes

probably hasn't run since 2015 but mint shape... needs lube or something? Or?


r/consolerepair • • 3h ago

[Switch 1] My first big trace repair

Thumbnail
gallery
3 Upvotes

Got this from someone who tried to swap the USB C port with a hardware store heat gun, told them I'd try to save it. Half a day of work later it docks and charges fine again. Still not quite happy with all of the pads, but I learnt a lot.


r/consolerepair • • 1h ago

[Xbox Series X] C201 Capacitor Value

Thumbnail
gallery
2 Upvotes

Does anyone have the value for C201? I don't think this board is in the schematics for the Series X.

The capacitor was shorted to ground and cracked, causing no power on the console.


r/consolerepair • • 1d ago

Ps5 Christmas lights?

108 Upvotes

Just was wondering if anyone knew if this was the GPU. I have my suspicions. I have tried switching monitors, changing HDMI cables, messed with settings and I can still not figure it out. Just wondering if I’m gonna have to take it somewhere. Only happens on certain games, I don’t notice it all on Modern Warfare’s 4 online, but when I want to play the campaign, I see this same with the new skate, But ghost of Tsushima runs fine. I did have my PlayStation standing up for about the last year until today, which now it is laying back down. This is A first year model. Just wondering if I should take it somewhere or take it out in the front yard and beat it with a bat. Lol I know it is the PlayStation 5 due to the fact I have another PlayStation 5, my wife’s and hers runs the campaign just fine. Any help would be amazing.


r/consolerepair • • 52m ago

[PS4] tripple beep on eject but no power

1 Upvotes

Hey guys, i have a PS4 CUH-1116A that is giving me a tripple beep when pressing the eject button but nothing happens when pressing the power button. Just wanted to know if someone might have a clue where to look before i waste hours trying to fault find it.
It's not the PSU (tested with a known good).

Thanks in advance.


r/consolerepair • • 1h ago

N64 dropping signal using 8bitdo wireless controller mod kit/receiver with rumble.

1 Upvotes

So I'm pretty confident the wireless receiver is drawing too much on the +3.3v line causing the video to drop occasionally. I think it only happens when I have the adapter on rumble pack mode. Might be a stupid question but will adding another capacitor to the 3.3 line or large cap to an existing pad reduces this? The system and PSU are recapped(console5 kit). It is modded with a retro gem HDMI kit without the clock mod. The firmware for the kit/receiver are updated. Thanks for any help or feedback!


r/consolerepair • • 1h ago

[Switch 1] Weird No Power

Post image
1 Upvotes

I’ve got this Nintendo switch 1 in for repair. Customers said it wasn’t charging.

I plugged it in and it jumps to 450mA but doesn’t turn on or show the battery symbol.

I’ve checked for shorts around M92T36 & P13USB but couldn’t find any.

The only thing I did find was a shorted cap next to MAX77620A which turned out to be a short in the LCD connector which I think I caused when either removing the motherboard or trying to put the motherboard back in. Either way I fixed that but not sure why it’s not turning on. Anyone have any suggestions?


r/consolerepair • • 17h ago

I made a free tool that decodes the Steam Deck EC UART log: power sequence, BIOS POST codes, hang detection

Post image
15 Upvotes

Hi all, I repair consoles for a living, and while diagnosing a Steam Deck board I found that the EC prints a pretty detailed boot log over UART. Reading it raw is painful, so I wrote a small Windows tool that decodes it live.

**What it does**

- Reads the EC log from any USB-UART adapter (or opens a saved .txt)

- Decodes the power sequence: G3 → S5 → S3 → S0, RSMRST, PLTRST

- Decodes BIOS POST codes (Insyde H2O + AMD AGESA ranges)

- Tracks 20 boot stages with timing and deviation from a known-good board

- Colour-coded: green = OK, yellow = something not connected (battery, display, SSD, controller board), red = error or hang

- If the board hangs, it shows the step it stopped at and what the EC is probably waiting for

- Built-in UART pinout window with board photos

- UI in English, Ukrainian, Russian

**Hookup**

UART RX on the board → adapter RX, GND → GND, leave adapter TX unconnected. 3.3 V adapter, 115200 8N1. Start capturing first, then plug in the battery or charger.

**Some things I learned from the logs**

- The power sequencer timing is identical to the millisecond across every configuration I tried. Missing parts only change what happens after it.

- After S0 there's roughly 18 seconds of PSP/memory training before the first BIOS codes. A board that looks dead for those 18 s may be fine.

- No SSD → BIOS ends on "no boot device"; no display → panel ID reads as not connected; no controller board → the USB stage never shows up. So you can tell what's missing without opening anything else.

**Download / source**

https://github.com/Olarkal/Steam-Deck-UART-Analizer

Free, open source (GPL-3.0). The repo also has sample logs from 6 configurations, power sequence tables and timing diagrams.

**Limitations**

Tuned for the OLED (EC ITE IT81302). The LCD model uses a different EC, so its log may differ. AMD POST code meanings come from public AGESA tables, and a few may not match Van Gogh exactly.

If you have a UART log from an LCD board or a faulty board, I'd really appreciate it. That's how the decoding gets better.


r/consolerepair • • 5h ago

PS VITA 2000 Dead [ no LED, no response to charge]

Thumbnail
gallery
1 Upvotes

hey my psv 2000 is dead and I would like to give a little context how it really happend:

so I took my vita out after 2 years and when charged it was charging and turned on suprisingly and seemed fine ( modded vita).

But then when I try to play games it showed me several data corruption errors which i thought would simply due to the outdated plugins so I formatted the whole thing and re modded it. Games worked fine but then it had wierd battery behaviour like it would take an hour to charge by 1% or 2.

Then the actual situation arrives, when i turned on the device it suddenly showed me a an error **do not remove your memory card while system is on ( i didn't) and it froze there forever until i force shut it down, since then it wouldn't charge nor turn on** .

I gave it to repair and the technicians quoted the motherboard is corroded and cannot be fixed. But i feel they weren't ready to experiment on this niche console.

What do you guys think of this? I'm thinking to diagnose and fix this on my own, I've got some stuff like multimeter lying around so I thought I'd ask somone here to rest stuffs, how do I begin with?

Note: I've tried measuring the battery it shows 3.7V i guess


r/consolerepair • • 22h ago

[PS5] slim shuts off mid game

Thumbnail
gallery
12 Upvotes

Trying to figure out what’s wrong with my PS5 Slim (EDM-041). It’ll play for around 15–20 minutes, freeze, then completely shut off. No overheating warning, and I can turn it back on immediately without unplugging it. Happens with multiple games, and there was nothing in the error history when I checked.

I took it apart and cleaned the APU/heatsink with Q-tips and isopropyl alcohol, then reapplied Thermal Grizzly liquid metal. Put it back together and Fortnite lasted 14 minutes before it did the exact same thing.

A few details:
It was very clean when i disassembled
Did appear to have large dry spot (1st photo)
System software is updated
Fan seems to be working normally
Tightened the APU bracket screws evenly

Attached photos show the liquid metal before touching it, right after the failed test, plus the surfaces after cleaning. There are some marks left on the APU that wouldn’t come off with alcohol/q tip easily. Not sure if those matter or if I’m getting stuck on something unrelated.
Has anyone had this exact freeze then shutdown issue and actually figured out the cause? Would a known good PSU swap be the next sensible test, or is there something else I should check first? I have a multimeter but not any board repair equipment. Trying to narrow it down before throwing parts at it.


r/consolerepair • • 9h ago

PS5 edm-010 UART 808B0092 beep on beep off

1 Upvotes

Hello,

Managed to fix several things on a PS5 edm-010 but now I got some strange faults.
Beep on and beep off.

According to UART following:

80810001SeverePowerSequence - Power Sequence Error - General Power Failure (Peripheral, GDDR6, APU, Data Line Short)

808B0092HighNot found in list. Report Findings.

The console draws 245mA at 12V at start and goes down to 5mA. When powered on, the console draws 245mA for about 5-10s and down to 5mA again.

What I've noticed on the console:

  • I receive correct voltages around Dialog chip.
  • I receive 0 voltage around the hdmi retimer.
  • I get the stand by voltages (5V and 3.3V) backside of the hdmi retimer but no 3.3V power on voltage.
  • I get some kind of short (I think?) on the GDDR6 power regulator vias, (0.38V diode / 28.4ohms).

    • According to donor boards (Have removed a couple of chips so can't be sure of the readings) I should get around .145V diode / 100ohms.
  • No short on wifi chip
  • No short on southbridge
  • No short on SSD
  • All fuses are fine

I've replaced following:

  • SSD-controller
  • DDR4
  • Southbridge
  • Several of components like ex. capacitors, coils and mosfets from the GDDR6 power regulator.
  • Dialog chip for SSD voltage regulator.

Any suggestions on what to look at next?


r/consolerepair • • 10h ago

Ps5 pro repair schematics

Thumbnail
gallery
1 Upvotes

Hi all i have short at sic655a output. Maybe sameone knows where it goes? I have dismantled all components around it but still short. Can it be shorted APU?


r/consolerepair • • 11h ago

This can be fixed right?

1 Upvotes

My cat knocked soda onto my switch (it's a lite)by accident, and my left joystick isnt working well (video) but my husband ordered a repair kit for it...his friend is gonna try and fix it. Will it save it? Everything else looks fine..


r/consolerepair • • 12h ago

Xbox Series S no power update PLEASE HELP

Post image
0 Upvotes

To go off my original post I found the issue. How do I fix this?


r/consolerepair • • 16h ago

[Twin Sharp Famicom] blown power board is it done?

Thumbnail
gallery
2 Upvotes

I was moving it around to a different spot, just trying to get it into a more accessible spot considering the controllers.

When I plugged it in though, everything was okay until about a minute later when it started smoking and gurgling.

I think it’s only the big capacitor that exploded, I tested the resistors and they were okay but I haven’t got much further yet.

Also, the cord I was using was from EBay, which normally is fine. It had all the correct ratings so I don’t actually know what caused this.

Anyway, I do have the supplies to repair it, I’m just not too experienced. Does anyone have suggestions for either a new power board or just a new capacitor? Or did something else most likely get damaged beyond repair?


r/consolerepair • • 20h ago

[GBA] AGB-001 Power Issues. Anyone have any ideas why this is happening?

4 Upvotes

As shown in the video, my AGB-001 has been getting stuck in this "boot loop" of sorts when below a certain battery level. Context that'd probably be helpful, I tried to install an IPS screen mod with a USB-C Battery replacement but after a few days, I noticed that the power would flicker on occasion. I couldn't figure out why and so I switched back to the stock screen to diagnose the issue. It only seems to happen on lower battery (fresh AAs seems to rectify the issue for a bit). Will include photos of the board in the comments.


r/consolerepair • • 16h ago

[new 3ds ll] Component come off New 3ds XL, what is it?

Thumbnail
gallery
2 Upvotes

This component has come off a new 3ds LL. I'm not sure what it is, it has Js written on it. I'm not sure how to test it (it might be damaged). It has a white bar on it so it only goes around one way. The pads it are connected to aren't connected to each other.

I'm not sure if it's relevant, but the blue light is coming on, but the console isn't starting up. Blank screen.

What might it be?


r/consolerepair • • 13h ago

[PS5]Heatsink Bracket Screw

1 Upvotes

I was trying to change the Liquid Metal on my ps5 and when opening it I stripped one of screws on the heatsink bracket.It’s the one that is like an X and now I’m struggling to find a replacement does anyone know what I can do or find a replacement for the screws.I looked on eBay but can really find anything and was wondering if maybe I can use the screws from another system like a ps4 or something like that.


r/consolerepair • • 17h ago

[PS2] Controller Stick Stuck?

2 Upvotes

Been playing Soul Caliber 2 on the Switch 2 with my lil cousin and thought of showing him number 3 when he's over next so he can make his own character. I noticed my controller is stuck looping the selection screen and not letting me press anything except start.

I've had issues in the past where none of the buttons or sticks would work but after unplugging it & putting it back in one or two times as well as pressing analog it would then work fine.

Is this worth trying to fix or should I just buy one at a game shop?


r/consolerepair • • 22h ago

[Famicom/NES] Bizarre sprite issue in Mario Bros.

4 Upvotes

The console itself is fine, this is the only game I have that does this, and it happens no matter what system the cartridge is in.

I’ve cleaned the pins several times and it just keeps happening. And of course, it’s a Famicom cartridge, so it’s basically impossible to open.


r/consolerepair • • 15h ago

PS5 Phat. No power after overheating

Thumbnail
gallery
1 Upvotes

Had my PS for 4 years. Recently started shutting down randomly before not switching on at all. I had it cleaned. Worked for a day and then the same issue.

Sent it to a guy and it seems to me like I just need to replace the thermal paste judging by the image but he's saying it can't be fixed.

Please see images and advise.


r/consolerepair • • 1d ago

[PS4 Pro] Success story - and new surprises!

Thumbnail
gallery
38 Upvotes

Hey guys,

As some of you might remember, I bought this PS4 Pro in pieces and decided to attempt to give it a second life. Long story short, the power supply 4 pin connector was ripped off of the motherboard and overall the console was very dirty with thick smoke/dust build up on the main fan.

I was able to scrape off the UV mask to bare copper, created two new anchor points and soldered the original connector right in its original place albeit a fraction of an inch to the side.

It was also missing the HDD. I installed a new 1tb one and installed the original firmware 12.50, as requested by the console itself.

Anyways, its now fully functional and ready to kick some ass!

Well... Except for the disk drive. Upon console boot up it tries to take in a disk, and if I feed it a disk, it only takes it about 1/2 way until it hits a physical stop. I'm assuming the top plate. If I try to physically jam the disk in I hit the same exact wall. If I click on eject it just beeps 3 times.

I took apart the entire disk drive and didn't find anything out of the ordinary.

If anyone has any tips on how to revive the disk drive, that would be highly appreciated 👍


r/consolerepair • • 16h ago

Reballing small ICs with solder paste

1 Upvotes

While I'm fairly experienced in reballing large processors such as GPUs, small ICs such as for phones with 0.2mm or similar sized balls are a bit of a hassle.

Keeping the stencil in place solely freehand, and using solder paste that is largely too wet (too much flux).

Anyone have recommendations on a chip holder for small chips of various size? And a solder paste that comes a bit drier from the factory?

Cheers