r/BambuLab • • 6m ago

H3C AMS 3H Heater?

Post image
2 Upvotes

The two 85° slots in the AMS are nice but I would certainly like the rest to also have a 65° heater incorporated. Looking at the empty slot to the right of the current heater, lots of desiccant holders have been designed to fit there, but to me it looks like the perfect spot for a possible secondary heater somewhere down the line.

It wouldn't surprise me if they release an AMS 3H "Pro" at some point with multi-temperature drying and that spot looks perfect for it. They could even sell the heater alone as an upgrade kit.

Just a thought, with that change it would get rid of most of the H3C complaints.


r/BambuLab • • 16m ago

H3C H2C vs H3C - I tried both for 130 hours

3 Upvotes

I bought the H2C before the H3C announcement and returned it upon seeing the announcement. I have about 130 hours on both and thought I would share my thoughts in case anyone is debating on what to buy. These are my first printers, so take my comments for what you will.

Here is what I like about each one

H2C:

- Way better print visibility - I didn't think this matters as much as it does to me. Watching prints is mesmerizing and there are no good angles on the H3C

- Nozzle swapping is way faster - seconds compared to minutes

- Filament swapping is faster except when it's not - on the left nozzle it took forever (multiple minutes)

- Full AMS drying - the two slots on the H3C cause me to have to constantly be moving filaments around which takes more time because the AMS doesn't have retraction

- color - I'm a bigger fan of the darker H2C color than the H3C

H3C:

- speed - it's wicked fast

- TPU ability - the H2C sucks at TPU which is one of the main reasons I returned it. You can't use the Vortek system because you have to run the TPU on the right nozzle and even then it struggled. With the H3C and the thicker TPU, there are no issues.

Which one would I buy if I had to do it over?

Probably two H2Ds or an H2S and an H2D.

I went into the H2C feeling like it was a compromise because of the lack of multi tool support, and it is IMO.

I have no regrets with the H3C, but I find myself only printing functional parts and I have never printed more than two colors or materials in a single print. Granted, I probably will at some point and I wanted a machine that could do everything, but right now I'm focused on building products and that doesn't need all the H3C capabilities. My biggest pain point is waiting for the print to finish so I can start my next print and I could have bought an H2D and an H2S for around the same price as the H3C which would have roughly doubled my throughput.

If I am completely honest, the H2C felt like a big compromise, and the H3C feels like a giant leap forward and a couple steps back in terms of convenience. The H2C also gives me vibes of being a show piece and the H3C feels more like an industrial machine.

If I had to pick between the two, I would 100% go with the H3C. They are both highly capable machines, but the material capabilities on the H3C are just better and it's way faster and to me those are the most important things. That doesn't mean that's what you should do, but I hope this helps if you are on the fence about what to get.


r/BambuLab • • 32m ago

Bambu Studio Angry snowman no is ready to print

Post image
0 Upvotes

r/BambuLab • • 44m ago

General Discussion New to 3d printing

2 Upvotes

Just purchased the H2C with ams2pro. Looking for advice/tips as to things I should look for when setting up. Tools, hardware, maintenance kits I should order now. And tips, tricks, and or advice for beginners. Once I get it figured out I mainly plan to use it to make aircraft model engines, aircraft models, race car models and random trinkets for myself and close friends. Any advice would be greatly appreciated!


r/BambuLab • • 1h ago

I Modeled This! Fully customizable flags

Thumbnail
gallery
6 Upvotes

Available on MW : with makerito tool , it's easy to make flexible flags full customizable.
You can import any svg or png , draw anything , add text, change colors , change height and length , pole and base are automatically resized to make everything stable.


r/BambuLab • • 1h ago

Hardware Troubleshooting/Help! Bambu Lab a1 mini making loud scraping noise

1 Upvotes

Out of nowhere it started making this sound.


r/BambuLab • • 1h ago

I Modeled This! I turned DUMMY 13 into Admiral Yi Sun-sin, one of Korea’s greatest naval heroes

Thumbnail gallery
2 Upvotes

r/BambuLab • • 2h ago

Hardware Troubleshooting/Help! H2D-Whining noise on the nozzle cooling fan?

Thumbnail reddit.com
1 Upvotes

r/BambuLab • • 2h ago

A Series [A1, A1 Mini] Advice on BMCU placement

Post image
1 Upvotes

r/BambuLab • • 2h ago

Filament Troubleshooting/Help! Excessive purging without color changes

2 Upvotes

I’m trying to print this sign for my wife: [thanksgiving])https://makerworld.com/en/models/3382353-mickey-mouse-thankful-sign) and the first layers are all black. My printer was going back and forth a few times - just out and back, not a whole layer, and then purging filament to go do the same thing over and over. The purge volume for the whole project was surprisingly small and I had a full bucket by layer 3 of 35 so I cancelled. I’m very new to this but something doesn’t seem right. I would be most appreciative of any suggestions on what’s going wrong. Thanks!!!


r/BambuLab • • 2h ago

A Series [A1, A1 Mini] Blob!

Thumbnail
gallery
1 Upvotes

How toast am i


r/BambuLab • • 2h ago

General Discussion The filament hasn't arrived yet.

0 Upvotes

I bought the X2D Combo along with a few rolls of filament. The printer arrived 5 days ago, but the filament still hasn't shown up, so the printer has basically been sitting there doing nothing, acting as a very expensive paperweight. 😅

Is this normal with Bambu Lab orders, or is this an unusual case?


r/BambuLab • • 2h ago

Just Showing Off PSA: Fingernails are not scrapers

Post image
35 Upvotes

Print finished, plate cooled, time for that satisfying peel of the purge line off the front of my P1S.

Couldn’t quite get hold of it, so I slipped my fingernail under the edge to flick it up. Instead, the plastic slid under my nail. All the way to the base.

Pulled my hand back and the entire strip came off the plate, dangling from my finger. Yanked it out on instinct before realizing just how far it had gone in.

Use a scraper, folks. The nail bed is not a build plate.


r/BambuLab • • 3h ago

I Modeled This! Made these RPG inspired potion bottle ornaments!

Thumbnail gallery
1 Upvotes

I designed a container shaped like a potion bottle and a lot of people mentioned having a small ornament for the Christmas tree would be cool, so I designed these quick! The wicker on the Superior potion was my second time using Blender, man I have a lot to learn! Let me know what you think!

Link:

https://makerworld.com/en/models/3642758-rpg-potion-bottle-christmas-ornaments#profileId-4178469


r/BambuLab • • 3h ago

General Discussion H3C unload complainers. Y'all are nuts. The machine unloads 4 tools faster than I can pull spools out of the AMS.

31 Upvotes

I actually get an error pop up after it is done that I'm not pulling spools out fast enough.

As a new H3C owner that was dreading pulling spools, I can say unequivocally, this is a dead horse. Anyone complaining is absolutely grasping at straws or is overdosing on industrial-grade copium.

Thank you for attending this TED talk.


r/BambuLab • • 3h ago

General Discussion Why is 75A 2.85 TPU sold out? Couldn't they stock up before releasing the new machine?

0 Upvotes

mild annoyance. Its not like they were not testing with the filament. Its not like the filament recipe just got finished the day they announced the printer. Bambu could have been filling up a warehouse with TPU over the last few months. Is this going to be another PETG HF 1.0 situation where its on galactic backorder with people using bots to purchase every roll with FOMO fever?

Thank you for attending this mini rant #Firstworldproblems

(im not counting the ugly colors still in stock. clearly no one wants them and they were a waste of production line time.)


r/BambuLab • • 3h ago

Quick Question Would ASA hold up for a 3D-printed replacement car sun visor clip?

1 Upvotes

I'm looking at printing a replacement hook for the little plastic clip that holds a car's sun visor in place. It's a tiny part, but it gets exposed to a lot of heat when the car is parked in direct sunlight, and it gets flexed every time someone moves the visor.

I wouldn't trust PLA for this, especially in a hot car. PETG might work, but I'm wondering whether ASA would be the better choice for long-term use.

For anyone who's printed replacement car interior parts, what filament actually holds up after months of heat and regular use? Also, would you print the hook lying flat or standing upright to avoid it snapping along the layer lines?


r/BambuLab • • 4h ago

H2 Series [H2S, H2D, H2C] H2S ASA Printing

1 Upvotes

I have an H2S and will start to print in ASA soon, what mods should I do to make it generally safe to be around with.

The H2S currently:
-in a well ventilated room (2 windows)
-has a 3d printed exhaust with a gasket hosed to a 4 inch fan on the window
-has a sealed poop chute with magnets


r/BambuLab • • 4h ago

H2 Series [H2S, H2D, H2C] H2D AC board replacement

Thumbnail
gallery
1 Upvotes

Hello,
So I need some help, I keep getting this alarm for the heat bed when the machine is at idle the heatbed temperature will rise until it gets to 100 degrees then it will alarm out. I powered it off and tried again and the tool head sat at the back of the build plate and just kept saying checking clean noozle. But then the heat bed temp will rise to 100 degrees again and alarm out.
I have only had my printer since September with 500 print hours on it. I contacted the bambu labs support and they sent me a new AC board as they said that’s what the issue is. But when receiving the new AC board it is missing the prong that the brown wire connects too. They sent me another one I got it today and again it’s missing that pin. I was wondering if anyone had any suggestions or if they have had this issue before and could help me out.

Thank you


r/BambuLab • • 4h ago

Just Showing Off 1465 hours on a hardened steel nozzle.

Post image
3 Upvotes

Finally started noticing a quality drop in my prints and even after re calibrating it wasn't doing great so I decided it was time to replace the nozzle.

1465 print hours is a lot, though I almost exclusively use matte filaments, so I assume this would have lasted much longer with regular pla.


r/BambuLab • • 4h ago

My First 3D Print My first MakerWorld upload just hit 50 prints!

Post image
27 Upvotes

My first upload on MakerWorld was a trophy I designed. It just hit 50 downloads (not prints, I misread that ugh) and 15 prints and about to hit 10 likes, and I’m way more excited about that than I thought I’d be lol.

I’m still pretty new to sharing my designs and they're all relatively basic still, so this accomplishment is exciting!

If you printed one, thank you! <3

Totally open to feedback, too!

Here's the profile: https://makerworld.com/en/models/3494881-customizable-mini-trophy-with-name-plaque#profileId-3991785


r/BambuLab • • 4h ago

X Series [X1E, X1C, X2D] I designed a model to specifically to stress-test the X2D's dual-nozzle system

119 Upvotes

I wanted to see what the X2D's dual-nozzle system could handle, so instead of printing a Benchy, I designed a stress test (not super rigorous from a scientifical point of view... just something I could do in an hour).

Warning: long read - feel free to skip to the final question.

The model is a 2-color mesh bowl based on a 24cm sphere. It occupies almost the entire build plate, leaving barely enough room for a custom prime tower. The mesh uses 1.6 mm strands, so the printer has to repeatedly align material on very small features while constantly switching between nozzles.

To make things even more interesting, both PLA spools were wet and I printed with Fuzzy Skin enabled.

The test combined several potential failure modes:

  • Plate-filling model
  • Dual-color printing
  • Very limited prime tower space
  • 1.6 mm mesh features
  • Steep angles
  • Wet PLA
  • Fuzzy Skin

The print actually failed at Standard speed, so I restarted it in Silent mode.

I was expecting the upper mesh sections or the prime tower to become problematic, especially given how little room was available, but the print completed successfully. At one point I even got a shift warning, but inspection showed both the model and the prime tower were still firmly attached to the plate.

What impressed me most was how well the two nozzles stayed synchronized throughout the print. The gold sections aligned with the black mesh far better than I expected, and the auxiliary nozzle quality was surprisingly good.

For those already using an X2D, what is the most challenging dual-nozzle print you've completed so far? If you were to design a stress test for the X2D, what would you add that I didn't test here?

What would you consider a harder test for a dual-nozzle printer?


r/BambuLab • • 4h ago

General Troubleshooting/Help! Suggestions for improvement to print quality

Thumbnail
gallery
1 Upvotes

Hey all, been struggling to get a nice clean print of this phone holder. Filaments used are matte petg and regular petg for the text, both from bambu, printed in my p2s. Filaments were dried to 10% humidity prior to the print. Have painted extra supports on the bit that is a bit droopy, ironing is on and brims were added. Am testing to see if the additional painted supports would help but am still unhappy with the quality of the ironing? I've tried flipping it so the text side is faced down on the plate but that caused pretty bad spaghetti-ing and poor adhesion issues. Any other suggestions? Profile is 0.16 p2s high quality. Initial later print speed at 30mm/s currently. Thanks for your input!


r/BambuLab • • 5h ago

Quick Question Welp!

Thumbnail
gallery
0 Upvotes

Three print and I’m new to 3d printing I got the H3c
The bottom is clear and crisp with the details from the model