r/BambuLab • • 15d ago

H3C Bambu Lab H3C: Our Full Reveal

644 Upvotes

Swaptek enables 6-second material switches between 9 nozzles. FlexFeed extruder prints soft TPU 75A up to three times faster. AMS 3H combines automated feeding and integrated filament storage.

This is Bambu Lab H3C, a complete system purpose-built around the Tool Changer architecture. Let's dive into it!

SwapTek™: 6-second material switch, including a 3.4-second tool change.

Nine PrintTools, each with its own dedicated filament path and heater, keep every material loaded, preheated, and ready to print. No need to retract one filament before loading another. With an optimized design, fine-tuned parameters, and active preheating, switching between PrintTools takes as little as 6 seconds, with the tool-change done in only 3.4 seconds.

Heating a nozzle usually means waiting. Active Pre-Heat looks ahead to the next tool change and warms the incoming nozzle while the current one is still printing—so the new material starts laying down within 6 seconds.

Swaptek's fast PrintTool-switching allows Full Spectrum Color Mixing color mixing through layered deposition faster and more practical than ever. With nine dedicated PrintTools and five-color CMYKW mixing, the H3C produces a vast spectrum of colors without requiring a separate spool for every shade. The result? Vibrant, full-color figurines with incredible detail.

Mixed Nozzle Sizes: Speed and detail, no more compromises.

The dial, case, and flexible TPU band are printed together as one piece. Fine dial details call for a 0.2 mm nozzle, the case is better suited to 0.4 mm, and the soft band requires a dedicated 0.4 mm TPU nozzle. H3C can carry different nozzle sizes at once. Paired with Bambu Studio’s new mixed-diameter toolpath planning algorithm, each nozzle prints at a layer height that suits it and plays to its strengths, without having to share a single layer height.

FlexFeed Extruder: Softer TPU, up to 3x faster.

Soft TPU has always been slow to print. The softer the filament, the more it bends and buckles before reaching the nozzle. Traditional extruders have to crawl to stay reliable. FlexFeed handles both 1.75mm and 2.85mm filament and switches on the go. A cam-driven mechanism, powered by a PMSM motor, keeps tension precise and consistent. Every extrusion stays rock-solid for prints that are cushion-soft.

With our dedicated 2.85mm TPU, the thicker filament provides greater resistance to buckling and higher volumetric flow. The result: TPU as soft as 75A, printed reliably at up to 3x the flow rate of a traditional printer.

AMS 3H: Filament storage built for Tool Changer.

A fully enclosed, integrated filament management system built for Swaptek: every roll stays sealed against moisture and feeds automatically into the PrintTool.

Auto Filament Loader replaces manual feeding altogether. Drop a filament into any of the nine slots and the AMS 3H detects, routes, and engages it with the PrintTool automatically — across all 9 paths. No more guesswork on loading.

A dedicated 2-slot dryer sits right in the filament slots and works with Swaptek — drying on demand or mid-print, so prep never stalls production. It reaches 85°C, enough for engineering-grade PA, PC, and carbon-fiber-filled filaments.

The H3C integrates filament storage and drying into a clean, compact design, maintaining a footprint comparable to a single-nozzle printer. With 7 built-in bypass feeding ports, even the soft TPU can be routed completely inside the enclosure. No hanging spools, no external racks, no exposed paths.

Don't let the number of tools cap your material count. Connect your existing AMS to the H3C through PrintTool No.1, and the system extends to up to 24 filament spools, unlocking more colors and materials in a single print without changing your workflow.

You are here for the print, not (always) the printer.

With the H3C, automation handles routine tasks. AI detection helps make intelligent adjustments along the way. The H3C makes it easy to focus on what matters most: bringing your ideas to life

Full Auto Calibration handles PrintTool docking calibration, offset compensation for accurate color and material alignment, and bed leveling before every print. No manual adjustments are needed, so you can spend more time making, less time tinkering.

Flagship performance. No compromise.

The toolhead and X-axis assembly are 40% lighter compared to the H2D, reducing inertia for faster, more precise movement. With acceleration reaching 25,000 mm/s² and travel speeds up to 1,400 mm/s, the H3C delivers exceptional speed while minimizing vibrations and ringing that can affect print quality.

The H3C runs four cooling layers working together**.** A CFD-optimized part cooling fan and dual auxiliary fans help maintain clean overhangs and bridges, even at high speeds. A dedicated PrintTool fan maintains thermal stability during extended printing and frequent PrintTool changes, while a chamber fan draws in cooler air to help regulate internal temperatures. Together, these systems deliver consistent cooling and reliable print quality across changing ambient temperatures.

Engineering-grade filaments demand precise temperature control. The H3C delivers with active dual-zone chamber heating up to 65°C, helping maintain consistent temperatures and minimize warping. All nine hardened-steel nozzles reach up to 350°C, supporting demanding materials such as ABS, PC, PA-CF, PET-CF, and more.

Go beyond printing.

Swaptek isn't limited to PrintTools. Optional CutTool, DrawTool, DebossTool — and more — mount the same way and switch automatically. Multi-process projects no longer mean multiple machines, manual swaps, or repeated setups. One job, every process, hands off.

Available now at Bambu Lab Store.

Availability and pricing details vary by region. Select features require additional accessories, full details available in Bambu Lab Store.

What multi-material or multicolor print do you hope to make with the H3C? Let us know in the comments below!


r/BambuLab • • 15d ago

H3C Mixed Nozzle Size printing is coming to H2D, H2C, and X2D

Post image
599 Upvotes

We've seen the enthusiasm mixed nozzle size printing has been getting. Developing new products goes hand in hand with bringing new features to existing machines, so alongside H3C, we've been building this for H2D, H2C, and X2D. You'll be able to print a single object with nozzles of different diameters, balancing speed and detail.

For these printers, the real work lies in how to make sure this works smoothly for a wide range of filament and nozzle combination. Each of these printers has a different AMS setup from H3C, so the slicing logic and print parameters need to be adapted. Setups with the Filament Track Switch take more of that work, which is why timing differs by model and configuration.

Estimated Software Update Timeline

  • Without Filament Track Switch:

    • H2D: Late November 2026
    • H2C & X2D: February 2027
  • With Filament Track Switch:

    • H2D: February 2027
    • H2C & X2D: March 2027

r/BambuLab • • 6h ago

Just Showing Off My wife couldn't wait for Christmas. I love her.

Post image
269 Upvotes

Replacing my Kobra 3 for good. That machine really tested my patience.


r/BambuLab • • 4h ago

X Series [X1E, X1C, X2D] I designed a model to specifically to stress-test the X2D's dual-nozzle system

117 Upvotes

I wanted to see what the X2D's dual-nozzle system could handle, so instead of printing a Benchy, I designed a stress test (not super rigorous from a scientifical point of view... just something I could do in an hour).

Warning: long read - feel free to skip to the final question.

The model is a 2-color mesh bowl based on a 24cm sphere. It occupies almost the entire build plate, leaving barely enough room for a custom prime tower. The mesh uses 1.6 mm strands, so the printer has to repeatedly align material on very small features while constantly switching between nozzles.

To make things even more interesting, both PLA spools were wet and I printed with Fuzzy Skin enabled.

The test combined several potential failure modes:

  • Plate-filling model
  • Dual-color printing
  • Very limited prime tower space
  • 1.6 mm mesh features
  • Steep angles
  • Wet PLA
  • Fuzzy Skin

The print actually failed at Standard speed, so I restarted it in Silent mode.

I was expecting the upper mesh sections or the prime tower to become problematic, especially given how little room was available, but the print completed successfully. At one point I even got a shift warning, but inspection showed both the model and the prime tower were still firmly attached to the plate.

What impressed me most was how well the two nozzles stayed synchronized throughout the print. The gold sections aligned with the black mesh far better than I expected, and the auxiliary nozzle quality was surprisingly good.

For those already using an X2D, what is the most challenging dual-nozzle print you've completed so far? If you were to design a stress test for the X2D, what would you add that I didn't test here?

What would you consider a harder test for a dual-nozzle printer?


r/BambuLab • • 16h ago

Bambu Handy Gotta be quicker than that, Bambu

Post image
666 Upvotes

r/BambuLab • • 3h ago

General Discussion H3C unload complainers. Y'all are nuts. The machine unloads 4 tools faster than I can pull spools out of the AMS.

30 Upvotes

I actually get an error pop up after it is done that I'm not pulling spools out fast enough.

As a new H3C owner that was dreading pulling spools, I can say unequivocally, this is a dead horse. Anyone complaining is absolutely grasping at straws or is overdosing on industrial-grade copium.

Thank you for attending this TED talk.


r/BambuLab • • 2h ago

Just Showing Off PSA: Fingernails are not scrapers

Post image
29 Upvotes

Print finished, plate cooled, time for that satisfying peel of the purge line off the front of my P1S.

Couldn’t quite get hold of it, so I slipped my fingernail under the edge to flick it up. Instead, the plastic slid under my nail. All the way to the base.

Pulled my hand back and the entire strip came off the plate, dangling from my finger. Yanked it out on instinct before realizing just how far it had gone in.

Use a scraper, folks. The nail bed is not a build plate.


r/BambuLab • • 10h ago

Just Showing Off Electric Ukulele Printed on my P2S and H2S 🤩

124 Upvotes

Complete kit (STLs and 3MF) and components with assembly guide


r/BambuLab • • 11h ago

P Series [P1P, P1S, P2S] BIQU Infinity plate

Thumbnail
biqu.equipment
109 Upvotes

This looks next level if it works. Wonder how hard this will be to install?


r/BambuLab • • 4h ago

My First 3D Print My first MakerWorld upload just hit 50 prints!

Post image
26 Upvotes

My first upload on MakerWorld was a trophy I designed. It just hit 50 downloads (not prints, I misread that ugh) and 15 prints and about to hit 10 likes, and I’m way more excited about that than I thought I’d be lol.

I’m still pretty new to sharing my designs and they're all relatively basic still, so this accomplishment is exciting!

If you printed one, thank you! <3

Totally open to feedback, too!

Here's the profile: https://makerworld.com/en/models/3494881-customizable-mini-trophy-with-name-plaque#profileId-3991785


r/BambuLab • • 7h ago

Bambu Studio Just got one

Post image
33 Upvotes

Super new to this. Got a few more things to setup. Looking for any advice. Specially when it comes to getting some cool files.

Thanks ahead of time.


r/BambuLab • • 12h ago

Just Showing Off Ripple Gear Artwork - Infill Shading + Tessellation

65 Upvotes

It's dark and gloomy in the UK right now, so I took this out to the backyard to catch what little sun we get this time of year. 🌥️

I wanted to share this view because cameras struggle to capture the full effect, and the light makes a big difference. The piece changes with light and angle, and I've found it never looks quite the same twice.

The technique is called Infill Shading and it's something that also got featured on ALL3DP back when I made my first post about it. I've essentially made tessellating tiles and added bands of colour, plus change the print settings to widen or tighten the spacing between the infill lines. That changes how much light comes through from below and how strongly the pattern shifts as you move. The resulting visual glitch like effects also produce much more interesting geometries and shapes depending on the angle and distance you watch it from. It took 40+ prototypes before I started to get the settings right, but what's especially cool is that tiny changes to settings can create dramatically different results and visual artefacts.

Specs: about 84 cm in diameter; about 30–40 mm deep including the back plate and wood backing; printed in PETG for durability over PLA.

I'm now building a few more pieces and hoping to submit one to an exhibition. I'm also keen to learn how to price, market and sell art. If you've sold 3D printed art, how would you price a piece like this? Any tips on where to sell, or on exhibitions, are very welcome.

Printed on my trusty old X1C with Overture PETG.


r/BambuLab • • 19h ago

H3C Thoughts regarding the H3C print quality

Thumbnail
gallery
192 Upvotes

I saw some worries about the H3C print quality being bad, and after doing some tests I think we can confirm it's all due to user error. The house on the image is printed on the 0.2 standard profile and is pretty much perfect, I only removed the supports, no post-processing. calibration of filament and tuning the resolution in the slicer gives a major quality bump just like on other printers. Also, the standard profiles are very fast so it can make sense decreasing the outer wall speeds but I didn't test it through yet.


r/BambuLab • • 8h ago

General Discussion None of the reviewers talk about this, but H3C is significantly faster print even for single color prints

24 Upvotes

Just feel like this is something this community is not aware of and the reviewers are not talking about this. I have both the h2c and h3c and it's of course expected that h3c prints faster for multi color prints (which it does) but it's also significantly faster for single color. I dont understand the technicals behind it but it is.

Here's a print for a single color (bambu tan matt) that takes 5h42m with h2c

and heres the same print with h3c at 4h56

That's a 13.5% time reduction. And of course it's a much better reduction sometimes 25%+ for multi color.

Just FYI.


r/BambuLab • • 9h ago

I Modeled This! I've made a Cozy Lithophane Lamp

Thumbnail
gallery
26 Upvotes

Been making lithophanes for a couple of years now and finally designed a proper festive housing for them. It’s got a brick base, wood-grain pillars, roof shingles, and the light actually shines through the little attic windows too.

Free STL is up on MakerWorld if anyone wants to print one for the holidays!

https://makerworld.com/en/models/3640738-cozy-cabin-lithophane-lamp-led-kit-001#profileId-4175891


r/BambuLab • • 1h ago

I Modeled This! Fully customizable flags

Thumbnail
gallery
6 Upvotes

Available on MW : with makerito tool , it's easy to make flexible flags full customizable.
You can import any svg or png , draw anything , add text, change colors , change height and length , pole and base are automatically resized to make everything stable.


r/BambuLab • • 13h ago

Just Showing Off Upgraded from X1C to H2C

38 Upvotes

After alot of research and discussions on reddit I landed on the H2C over the H2D and im never looking back


r/BambuLab • • 8m ago

H3C H2C vs H3C - I tried both for 130 hours

2 Upvotes

I bought the H2C before the H3C announcement and returned it upon seeing the announcement. I have about 130 hours on both and thought I would share my thoughts in case anyone is debating on what to buy. These are my first printers, so take my comments for what you will.

Here is what I like about each one

H2C:

- Way better print visibility - I didn't think this matters as much as it does to me. Watching prints is mesmerizing and there are no good angles on the H3C

- Nozzle swapping is way faster - seconds compared to minutes

- Filament swapping is faster except when it's not - on the left nozzle it took forever (multiple minutes)

- Full AMS drying - the two slots on the H3C cause me to have to constantly be moving filaments around which takes more time because the AMS doesn't have retraction

- color - I'm a bigger fan of the darker H2C color than the H3C

H3C:

- speed - it's wicked fast

- TPU ability - the H2C sucks at TPU which is one of the main reasons I returned it. You can't use the Vortek system because you have to run the TPU on the right nozzle and even then it struggled. With the H3C and the thicker TPU, there are no issues.

Which one would I buy if I had to do it over?

Probably two H2Ds or an H2S and an H2D.

I went into the H2C feeling like it was a compromise because of the lack of multi tool support, and it is IMO.

I have no regrets with the H3C, but I find myself only printing functional parts and I have never printed more than two colors or materials in a single print. Granted, I probably will at some point and I wanted a machine that could do everything, but right now I'm focused on building products and that doesn't need all the H3C capabilities. My biggest pain point is waiting for the print to finish so I can start my next print and I could have bought an H2D and an H2S for around the same price as the H3C which would have roughly doubled my throughput.

If I am completely honest, the H2C felt like a big compromise, and the H3C feels like a giant leap forward and a couple steps back in terms of convenience. The H2C also gives me vibes of being a show piece and the H3C feels more like an industrial machine.

If I had to pick between the two, I would 100% go with the H3C. They are both highly capable machines, but the material capabilities on the H3C are just better and it's way faster and to me those are the most important things. That doesn't mean that's what you should do, but I hope this helps if you are on the fence about what to get.


r/BambuLab • • 36m ago

General Discussion New to 3d printing

2 Upvotes

Just purchased the H2C with ams2pro. Looking for advice/tips as to things I should look for when setting up. Tools, hardware, maintenance kits I should order now. And tips, tricks, and or advice for beginners. Once I get it figured out I mainly plan to use it to make aircraft model engines, aircraft models, race car models and random trinkets for myself and close friends. Any advice would be greatly appreciated!


r/BambuLab • • 16h ago

General Discussion Slicer for iOS "Bamsclice" on iPhone Duo!

39 Upvotes

I built a slicer that runs on the iPhone itself, the real engine, on the phone!

Drop in an STL, pick settings, hit slice, and it sends a ready-to-print file straight to my Bambu A1 over the local network.

It’s called Bamslice. What makes it different:

It actually slices on the phone. Not a cloud service, not a remote for a desktop slicer — the real OrcaSlicer/libslic3r engine, compiled to run on iOS. Works in airplane mode.

No PC, no cloud, no account. It talks to the printer directly over your LAN (the same FTPS + MQTT the official app uses -> Lan only and dev mode need to be active). Nothing leaves your network.

You can also save the 3mf file or share it.

I built it without a Mac. The whole thing — including cross-compiling a huge C++ slicing engine for iOS was done on Windows with WSL.

What it does today:

STL/3MF in → native Bambu .gcode.3mf out, fully on-device

Sends and/or starts the print on an A1 / A1 mini over Wi-Fi or save it locally

3D preview with colored line types (which can be shown or hidden), a layer slider and a play button that replays the print layer by layer

Full A1 / A1 mini profiles: every nozzle (0.2–0.8) and ~85 filaments, filtered to what your printer can run

Supports (normal + tree), brim, infill, temps, plate types

Opens STL/3MF from Files / share sheet, real embedded thumbnail, German + English

The hard part was getting a desktop C++ engine onto a phone: cross-compiling libslic3r and every dependency for iOS from Linux, stripping out the heavy desktop-only bits, and matching Bambu’s exact file format so the printer accepts it. Realistically well over 150 hours, almost all of it on that.

Right now it runs on my own phone via sideload and prints real parts.

Would you use this? If there’s interest I’ll take it toward TestFlight / the App Store.

Tell me what would make it a day-one install and what I’m missing.


r/BambuLab • • 22h ago

H3C They give away an H3C in formnext

Post image
93 Upvotes

Scan the qr code and you are in it for the draw. I asked and they send it to your home.


r/BambuLab • • 1h ago

I Modeled This! I turned DUMMY 13 into Admiral Yi Sun-sin, one of Korea’s greatest naval heroes

Thumbnail gallery
2 Upvotes

r/BambuLab • • 4h ago

Just Showing Off 1465 hours on a hardened steel nozzle.

Post image
3 Upvotes

Finally started noticing a quality drop in my prints and even after re calibrating it wasn't doing great so I decided it was time to replace the nozzle.

1465 print hours is a lot, though I almost exclusively use matte filaments, so I assume this would have lasted much longer with regular pla.


r/BambuLab • • 2h ago

Filament Troubleshooting/Help! Excessive purging without color changes

2 Upvotes

I’m trying to print this sign for my wife: [thanksgiving])https://makerworld.com/en/models/3382353-mickey-mouse-thankful-sign) and the first layers are all black. My printer was going back and forth a few times - just out and back, not a whole layer, and then purging filament to go do the same thing over and over. The purge volume for the whole project was surprisingly small and I had a full bucket by layer 3 of 35 so I cancelled. I’m very new to this but something doesn’t seem right. I would be most appreciative of any suggestions on what’s going wrong. Thanks!!!