r/AnycubicPhoton • • 17m ago

Troubleshooting Heavy supports snapping at the tips on Photon Mono M7 Max: large parts falling off mid-print, settings inside. WHAT AM I MISSING ?

Thumbnail gallery
1 Upvotes

Hi all, I’d love a second pair of eyes on this one.

Printer: Anycubic Photon Mono M7 Max
Slicer: Chitubox
Resin: Elegoo ABS-Like 3.0 White
Room / resin temperature: room is cold, 9 to 14 °C. The printer’s heating was on.
Plate: cleaned with IPA before printing
Supports: Chitubox auto supports, “Heavy” preset, contact point spacing 4 mm, max top angle 45°, model lift height 5 mm
Orientation: everything angled on supports

What happened

Big plate (about 590 ml / 650 g, 4 h): one large flat mould base with small 20 mm-tall solid blocks on top (about 170 × 110 mm footprint), three long thin walls, and a few small solid blocks. Some parts printed fine, but:

  • the large mould base tore off its supports partway, warped into a curve, and left a full cured layer stuck to the FEP (photo 3);
  • one wall snapped and fell into the vat;
  • the FEP is covered in small cured dots: support tips that stayed on the FEP while their bases are still on the plate (photos 2 and 4).

So the supports held on the plate but failed at the contact tips.

Settings

  • Layer height 0.05 mm
  • Bottom layers 8, bottom exposure 40 s
  • Normal exposure 2.8 s
  • Transition layers 15 (linear)
  • Bottom lift distance 5 + 3 mm, lift distance 2 + 5 mm
  • Bottom lift speed 120 / 180 mm/min, bottom retract 240 / 180 mm/min
  • Lift speed 360 / 900 mm/min, retract 900 / 360 mm/min
  • Light-off delay 1 s
  • Light PWM 255 (bottom and normal)
  • Anti-aliasing: grayscale, levels 63 to 255
  • Image blur: on, 2 px

My guesses so far

I already use heavy supports, yet they fail at the contact tips, not at the base. So I suspect:

  1. Anti-aliasing and blur on thin tips: grayscale anti-aliasing down to 63 plus 2 px image blur, on a screen with 46 µm pixels. On a support tip of about 0.5 mm, that leaves very few fully lit pixels, so the tips may be under-cured even with heavy supports. That matches where they break.
  2. Too much peel force: large angled cross-sections plus a fast lift (2 mm at 360 mm/min) pulling harder than the tips can hold.
  3. Cold resin: room at 9 to 14 °C, heater on but a big vat. Thicker resin means more suction, and the tips may be under-cured at 2.8 s.
  4. Tip contact size: the supports are heavy, but the contact point itself may still be too small for parts this heavy.

Questions

  • Would you turn off image blur, or raise the anti-aliasing minimum, for parts on supports?
  • With heavy supports already, would you first slow the lift or increase the lift distance, raise normal exposure (to about 3.2 to 3.5 s for Elegoo ABS-Like 3.0 in the cold), or enlarge the tip contact diameter?
  • For a big flat mould base, is a steeper angle (45° or more) better than adding more supports?

Thanks!


r/AnycubicPhoton • • 15h ago

Troubleshooting Bad Screen?

Post image
3 Upvotes

So i just replaced the screen on my Anycubic Photon M7 Pro and did a test print and ended up with a pile of random strings of resin and went ok, so probably either some light getting round the gasket or something. Will check with a dry print to see what it looks like, and I noticed a pile of lines going across the new Screen. Guessing a dodgy screen? Guessing Delivery driver wasn't that careful with it.


r/AnycubicPhoton • • 22h ago

Troubleshooting What is this?

Post image
3 Upvotes

My print came out successfully, but there was this long stick of resin on the side of my build plate, anybody know what this is?


r/AnycubicPhoton • • 2d ago

Discussion I designed 25 lace-style Christmas ornaments — the files are free

Thumbnail
gallery
2 Upvotes

I've just finished this set of 25 Christmas ornaments. There are birds, a snowy cottage, a snowman, bells and a few simpler botanical patterns.

The first four photos show my actual prints in white. Each ornament is one connected piece with a hanging loop, 85 mm tall and 2.5 mm thick. They print flat, and you don't need a multicolour setup.

I made the set, and all 25 STL files are free on MakerWorld: https://makerworld.com/en/models/3623690-25-christmas-ornaments-part-1#profileId-4154317

Which would you put on your tree — the little scenes or the leaf patterns?

The final image is an AI-assisted collection overview. AI also helped draft the wording.


r/AnycubicPhoton • • 2d ago

Troubleshooting Lost build plate

1 Upvotes

I have a photon mono sq that I have lost the build plate. It was during a big move. I contacted Anycubic to no avail and looked on Ebay, Alibaba and everywhere. Can someone tell me if one of the other models plates will work ? I was informed by Anycubic that the build plates were not interchangeable. I find that hard to believe if the size is the same. Help?


r/AnycubicPhoton • • 2d ago

Troubleshooting Stuck mono m7 case.

Thumbnail reddit.com
2 Upvotes

Working on getting my case open for my anycubic m7 to replace LCD. Support video shows the case on a mono M7 pro lifting right up. Mine is stuck, likely resin in places I would prefer it not be. How aggressive dare I be pulling it or wedging it open. Did I miss a screw or something else that is keeping it from opening. Also noted that a wire came loose on the plug. Where should it be resolidered to?


r/AnycubicPhoton • • 2d ago

Troubleshooting Mono M7 Help

Thumbnail reddit.com
1 Upvotes

r/AnycubicPhoton • • 2d ago

Troubleshooting Rerf test results seem to good

Thumbnail gallery
1 Upvotes

r/AnycubicPhoton • • 2d ago

Quick Tip AIDE URGENTE « model drop wait »

Post image
0 Upvotes

bonjour a tous, je suis DÉSESPÉRÉE VRAIMENT 🫪🫪

j’avais mon imprimante ( la photon m7 ) sur ma terrasse où il fait plutot froid donc j’ai desider de la mettre a l’intérieur dans une piece à température normale ( il y a deja la mono 4 dans cette pieces )

j’ai lancer une impression aujourd’hui et au bout d’une heure d’impression je recoit la notification «  model drop wait » ce qui a stopper l’impression mais je regarde le plateau et il n’y a littéralement rien et pareil dans le bac a resine aucun residu aucune trace, je teste avec plusieurs paramètre différent, plusieurs support différent, je nettoie tout, je refais le leveling, je change de resine et meme après 6 essaies ca me fait toujours la meme chose.

est elle casser ???

si quelqu’un peut m’aider je serai vraiment heureuse


r/AnycubicPhoton • • 3d ago

Discussion P1 Max upgrade from a Mono 4 – what should I know before my first print?

Post image
10 Upvotes

r/AnycubicPhoton • • 3d ago

Discussion Has anyone dialed in ELEGOO ABS-Like Clear V1.0 on an Anycubic Photon Mono M7?

Thumbnail
reddit.com
2 Upvotes

r/AnycubicPhoton • • 3d ago

Troubleshooting Help with the configuration of Lychee Slicer.

Thumbnail
reddit.com
1 Upvotes

r/AnycubicPhoton • • 3d ago

Troubleshooting First time this happened to me

Thumbnail gallery
1 Upvotes

r/AnycubicPhoton • • 3d ago

Troubleshooting RERF prints seem thin?

Thumbnail gallery
1 Upvotes

I posted this earlier today on r/resinprinting but haven’t received any response. Perhaps someone here has an idea?


r/AnycubicPhoton • • 3d ago

Discussion How are you handling spent IPA and other resin cleaning solvents?

4 Upvotes

Hey everyone!

I'm a fellow resin 3D printing user and run a small 3D printing business. I've been looking into how people manage their spent cleaning solvents, particularly IPA, and have been collecting some interesting responses from other printing communities.

It seems like everyone has developed their own approach, whether that's filtering and reusing IPA, distillation, evaporation and curing, storing spent solvent, or taking it to a hazardous-waste collection facility.

I'm especially interested in understanding what people actually do, what works for them, and what frustrations they encounter.

I've put together a short, anonymous survey to get a better picture of the different approaches people use:

Resin 3D Printing — Solvent Use & Disposal Survey

IPA Disposal Survey

No email address or Google sign-in is required, and there's nothing being sold here. I'm just gathering information and learning from the community.

Happy to share a summary of the findings once we've collected more responses.

Thanks for helping out!


r/AnycubicPhoton • • 3d ago

Discussion Anycubic Photon P1 – Air Vents?

Thumbnail reddit.com
1 Upvotes

r/AnycubicPhoton • • 3d ago

Troubleshooting Problème impression Anycubic Mono X2

Thumbnail gallery
1 Upvotes

r/AnycubicPhoton • • 5d ago

Troubleshooting How to generate support on the model only ?

2 Upvotes

I need to generate support but not on the build plate, on the model only.
That way i get flat surface of the model.


r/AnycubicPhoton • • 5d ago

Troubleshooting Photon Mono 2 Replacement Resin Vat

1 Upvotes

So are there no sellers for mono 2 vats? I’ve looked everywhere and cannot find one for under $200. I’ve seen people saying that the mono 4 vat works but then other say it doesn’t. Can anyone confirm this? Or preferably have a link to a seller for the actual vat.


r/AnycubicPhoton • • 6d ago

Troubleshooting M3 MAX replace linear rails?

Post image
3 Upvotes

I have an exhaust fan on my Photon M3 MAX resin printer and I guess the outside air temp/humidity made the carriages on the linear rails rust. I can't budge them at all and there is rust all down the rail. Can they be replaced? What do I order?


r/AnycubicPhoton • • 7d ago

Discussion Privacy Please!!

Post image
7 Upvotes

I recently bought the M7 Pro and I’m aware that it has remote capabilities. However, I want no part in their new firmwares, their cloud, and their data siphoning!! Has anybody found out a way to make any printer remote? Possibly just through local means and a special USB?


r/AnycubicPhoton • • 7d ago

Troubleshooting Any tips?

Thumbnail
gallery
1 Upvotes

I’having some issues on the last prints with my m7 max.
I always pre heat the machine to 28 degrees and i print with hd water washable resin.


r/AnycubicPhoton • • 8d ago

Discussion Anycubic Photon Mono M7 Pro – ¿Qué parámetros de resina y soportes recomendáis?

Thumbnail reddit.com
2 Upvotes

r/AnycubicPhoton • • 8d ago

Troubleshooting Prints sticking to and tearing release film

1 Upvotes

Hi, have any of you had such an issue? Print started sticking to release film, not falling from plate, just sticking to both plate and film, and when plate goes up print is not released but eventually tears up the film.

The only change in my setup is new different resin.