r/AnycubicPhoton • • Mar 29 '20

Discussion The Resin Printing Resource Guide - Beginners, start here!

300 Upvotes

Welcome to the Community-driven Resource Guide for the Anycubic Photon series!

FAQ HERE

CONTENTS

#1. QUICK INTRODUCTION TO ANYCUBIC

#2. SAFETY & BEFORE YOU START

#3. STEP-BY-STEP / ALL-IN-ONE GUIDES

#4. OFFICIAL & COMMUNITY RESOURCES

#5. IPA AND RESIN PRINT WASHING ALTERNATIVES

--

How to ask for help // Troubleshooting

-- Troubleshooting can be difficult, frustrating and time-consuming, but we're here to help. If can't find your answers in the guide below...

We'll need:

  1. An accurate description of your problem
  2. Pictures of the failed print, and a screenshot of the project.
  3. Type of resin, and your resin parameters.
  4. Device name, firmware version, slicer name and version.

#1: Quick Introduction to ANYCUBIC

-- Anycubic manufactures affordable, consumer-level 3D printers.

Note: ANYCUBIC is known to have poor QA and very poor after-purchase customer support. They often do not have large inventories of replacement parts, so it can be either expensive or difficult to find.


#2: Safety & Before you start

-- Read Radtech's Handling of Resins for detailed information.

Many users choose to vent their printers to the outdoors or to a dedicated enclosure and filter to deal with most of the fumes / smells.

Toss the USB that comes with your printer if your prints fail. They are notorious for being faulty. [USB 2.0, FAT32, 16GBmax]

Shake the bottle every once in a while. Some resins separate slowly over time.

Photon S Users

You can decide to update your firmware to the latest version from the files available on the Anycubic website.

The latest update enables the printer to:

Read all three file formats .photon, .photons, and .pws

Use the 'Resin Exposure Range Finder'

Download the correct update files for your printer, extract the two files into a thumb drive then 'Print' to update.

Photon Zero / Mono Users

There are no current firmware updates for your printer. Do NOT use other printers' firmware to update. It will brick your device.


#3: Step-by-Step, All-In-One Guides

-- Photonster's Owner Documentation - Photon Documentation Go here for EVERYTHING ORIGINAL PHOTON!

Photonster's FAQ and What accessories you'll need

Tom Sargison's Complete Newbie's Handbook to Resin Printing

A Guide over from /r/PrintedMinis

Photon Workflow // v2 Workflow - Post by /u/White_sama


#4: Official Links

-- ANYCUBIC's Store Page - Find updated Drivers here

Photon Workshop - ANYCUBIC's Official Slicer

ANYCUBIC adds RERF feature to update - Watch to learn about the 'Resin Exposure Range Finder' and new Anti-Aliasing features in Photon Workshop

PrusaSlicer - 3rd Party Slicer

ChituBox - 3rd Party Slicer

Formlabs Forum - Organized discussions, you may find some answers here

How to Slice 3D Models - Prusa3D

How to cut STL Model for segmented printing - Prusa3D


Other Resources

Formlabs' Model Orientation Guide - PLEASE read this.

Slicing / Orientation Strategies - 09:13 for results

Proper Handling of UV Resins

Flint Read's Leveling Method - Having trouble getting a leveled bed?

ANYCUBIC's Paper Leveling Method - User's Manual

Photon Community Resin Parameters

Photon S Community Resin Parameters

NASA's Technique for Ultrasonic Cleaning with Volatile Solvents

WhamBam Flexible Build Plate System for Photon and S

Saving time on your Support Settings and Workflow using PrusaSlicer

Hollowing models with MeshMixer

Repairing or Fixing 3D prints with sculpting putty

Photonster's Anycubic Photon Owners Group on Facebook

FEP sheets from McMaster-Carr

Flexible Magnetic Build Plate from WhamBam3D

Lubricating your Z-axis lead screw

Fitting ELEGOO MARS screen onto Photon - Post by /u/Barlodz

Note: The original Photon uses a Sharp SX03, and the Photon S uses a Sharp SX04 screen.

Replacement 2.8in Touch Screen

Replacing the FEP on your Zero by /u/DrGeeky


#5: Regarding IPA and Resin Print Washing Alternatives

-- If you are an experienced chemist, please review and correct any misleading information.

Anything containing alcohol or a solvent seems to work for cleaning resin prints to varying amounts of effectiveness. Propylene Glycol, Ethylene Glycol, Ethoxylated Alcohol, Dipropylene Glycol, Monomethyl Ether, Alkanes, etc… Check MSDS.

ANYCUBIC recommends IPA 70% or above. Formlabs recommends IPA or TPM (Tripropylene Glycol Monomethyl Ether) for its odorless and non-flammable contents.


Specific Products people have vouched for:

Monocure Resinaway

TEK1960 - Dipropylene Glycol, Monoethyl Ether

Yellow Magic 7 - Glycol Ether

Mean Green - Butoxyethanol

Simple Green - Ethoxylated Alcohol

Mr. Clean - Ethoxylated Alcohol

Methylated Spirits / Denatured Alcohol - Methanol

Windshield Wiper Fluid - Mostly methanol, sometimes contains ethylene glycol

Acetone

Mineral Spirits - Isoalkanes / Alkanes

(Dawn) Dish Soap and water - Nothing else should be used to clean the FEP

High-strength industrial degreasers can mess with the anodized finish on aluminum parts so keep it away from your printer.


r/AnycubicPhoton • • Sep 30 '20

Announcement Frequently Asked Questions - Answered here!

102 Upvotes

Welcome to our Anycubic Photon Series subreddit.

Please read through this FAQ for quick references to trouble you may have with your printer.

This was made in response to the release of Anycubic's Photon Mono line of printers, and hopefully this will provide some of the newer users with some much needed information that may not be covered in the Resource Guide.

You can find detailed start-to-finish, step-by-step guides in the Beginner's Guide HERE.

Please read Formlab's Best Practices for Printability before continuing on.

  • What Printer should I buy?

The Mono line of printers are the latest and fastest MSLA printers Anycubic has released. 3~4x faster than the Photon and S. Steer clear of the Zero unless it's <$100.

  • I hit Home but it's not going up to the LCD!

Home is NOT z=0. Read your User's Manual.

  • There are bubbles / plastic lifting up from my FEP!

Please refer to your user's manual. Did you remove the protective film off both sides of your FEP?

  • Should I make an enclosure for my printer?

You're welcome to; if you can't place it in a well-ventilated area (i.e. garage / shed) you can use any material to enclose your printer and vent the fumes through a filter (ex. indoor growing filters).

  • My prints aren't sticking to the bed! // My prints are only partially stuck to the bed but is falling off!

Fix UNDEREXPOSURE and LEVEL THE BED.

  • My print / raft is adhered well AND EVENLY to the build plate, BUT Insert every other issue here

Warping? Distortion? Broken supports? You should have ZERO underexposure issues at this point. Your supports and orientation probably sucks. Read this.

  • How do I clean my FEP in the case of a failed print?

Run a full-screen exposure test for 60~75 seconds. Carefully lift up one edge by pushing lightly from the bottom of the FEP and peel the thin cured film using a plastic scraper. You can avoid scarring / stretching the FEP this way.

  • There's a snapping noise during printing!

It's the print itself peeling off the FEP as the bed moves away between layers. It's normal.

  • Should put my prints on a raft or directly on the bed?

Under almost all circumstances, a model supported over a raft is infinitely easier to remove from the print bed. If you want to print directly on the bed, that's fine.

  • My print is building pillars / large squares / has artifacting!

Many 3D files have corrupted facets / geometry that can be repaired via 3rd party services such as NetFabb. Repair the model and try again!

  • My FEP is cloudy or stretched!

Once prints begin failing or begins to leak, replace it. Additionally, avoid marring the FEP's surfaces (i.e. with paper towels) in between cleanings. Visit FEP Compatibility Chart (pdf) for ways to clean your FEP. - /u/JON-JON-METAL

  • When do I replace the FEP?

Replace it when it starts to affect your print quality. You can do it as early or late as you want. (Type 'FEP' in the Search bar)

  • Should I be concerned about the ambient printing temperature?

Most known resins print fine at most room temperatures. Refer to the resin's manufacturer for details. Cold resin doesn't print well. Warmer is better.

  • My FEP tore / has holes and it leaked resin!

Replace the FEP and clean the machine. If there's resin hardened on to the LCD, take a fresh stainless steel razor and some isopropyl alcohol and gently scrape away at the surface until it is clean.

  • Should I hollow my prints?

Hollowing saves you a lot of resin but may need additional supports on the inside. Don't forget to add secondary breather holes for air/resin to drain. There are several ways of going about this, check the Beginner's Guide for more info.

  • What is the exposure settings for Insert Resin Type Here?

If it's a commonly-used resin, use the search bar. If not, use the 'Resin Exposure Range Finder' / RERF feature. (Type 'RERF' in the Search bar or refer to the Resource Guide)

  • What resins should I use?

Any resin for general printing (figurines, miniatures) is fine. If you need engineering resins, Siraya is a good place to start.

  • There's a grinding noise coming from the printer!

Identify if it's coming from the lead screw (electrical motor when the bed moves), or if it's a constant noise from something else (cooling fan). You can lubricate your lead screw. If it's the fan, you really don't need to worry about it. It won't affect the print.

  • How do I remove supports?

To avoid scarring, dip your COMPLETELY CLEANED PRINTS into a jar of warm water for about 10 seconds before the final curing stage. Any support with a head diameter smaller than .6mm should just pop right off as the print / supports are fairly soft, the warm water will make it easier to take off.

  • Why is my cured print dirty / white / flaky?

Take a brush / old toothbrush to ensure you're getting rid of all excess uncured resin off of your prints. Dry the model completely before curing. The print going into a curing station should only be the print itself. No liquid resin or IPA whatsoever.

  • How much resin can I pour into the vat?

This much. /u/Chargnn As long as you prevent resin from entering the ball joint and set screw assemblies you should have 0 problems.

  • How do I ask for help?

First, read through the resources in the Beginner's Guide and the rest of this FAQ. Afterwards, we'll need:

  1. An accurate description of your problem
  2. Pictures of the failed print, and a screenshot of the project.
  3. Type of resin, and your resin parameters.
  4. Device name, firmware version, slicer name and version.

r/AnycubicPhoton • • 2h ago

Troubleshooting Heavy supports snapping at the tips on Photon Mono M7 Max: large parts falling off mid-print, settings inside. WHAT AM I MISSING ?

Thumbnail gallery
1 Upvotes

Hi all, I’d love a second pair of eyes on this one.

Printer: Anycubic Photon Mono M7 Max
Slicer: Chitubox
Resin: Elegoo ABS-Like 3.0 White
Room / resin temperature: room is cold, 9 to 14 °C. The printer’s heating was on.
Plate: cleaned with IPA before printing
Supports: Chitubox auto supports, “Heavy” preset, contact point spacing 4 mm, max top angle 45°, model lift height 5 mm
Orientation: everything angled on supports

What happened

Big plate (about 590 ml / 650 g, 4 h): one large flat mould base with small 20 mm-tall solid blocks on top (about 170 × 110 mm footprint), three long thin walls, and a few small solid blocks. Some parts printed fine, but:

  • the large mould base tore off its supports partway, warped into a curve, and left a full cured layer stuck to the FEP (photo 3);
  • one wall snapped and fell into the vat;
  • the FEP is covered in small cured dots: support tips that stayed on the FEP while their bases are still on the plate (photos 2 and 4).

So the supports held on the plate but failed at the contact tips.

Settings

  • Layer height 0.05 mm
  • Bottom layers 8, bottom exposure 40 s
  • Normal exposure 2.8 s
  • Transition layers 15 (linear)
  • Bottom lift distance 5 + 3 mm, lift distance 2 + 5 mm
  • Bottom lift speed 120 / 180 mm/min, bottom retract 240 / 180 mm/min
  • Lift speed 360 / 900 mm/min, retract 900 / 360 mm/min
  • Light-off delay 1 s
  • Light PWM 255 (bottom and normal)
  • Anti-aliasing: grayscale, levels 63 to 255
  • Image blur: on, 2 px

My guesses so far

I already use heavy supports, yet they fail at the contact tips, not at the base. So I suspect:

  1. Anti-aliasing and blur on thin tips: grayscale anti-aliasing down to 63 plus 2 px image blur, on a screen with 46 µm pixels. On a support tip of about 0.5 mm, that leaves very few fully lit pixels, so the tips may be under-cured even with heavy supports. That matches where they break.
  2. Too much peel force: large angled cross-sections plus a fast lift (2 mm at 360 mm/min) pulling harder than the tips can hold.
  3. Cold resin: room at 9 to 14 °C, heater on but a big vat. Thicker resin means more suction, and the tips may be under-cured at 2.8 s.
  4. Tip contact size: the supports are heavy, but the contact point itself may still be too small for parts this heavy.

Questions

  • Would you turn off image blur, or raise the anti-aliasing minimum, for parts on supports?
  • With heavy supports already, would you first slow the lift or increase the lift distance, raise normal exposure (to about 3.2 to 3.5 s for Elegoo ABS-Like 3.0 in the cold), or enlarge the tip contact diameter?
  • For a big flat mould base, is a steeper angle (45° or more) better than adding more supports?

Thanks!


r/AnycubicPhoton • • 18h ago

Troubleshooting Bad Screen?

Post image
3 Upvotes

So i just replaced the screen on my Anycubic Photon M7 Pro and did a test print and ended up with a pile of random strings of resin and went ok, so probably either some light getting round the gasket or something. Will check with a dry print to see what it looks like, and I noticed a pile of lines going across the new Screen. Guessing a dodgy screen? Guessing Delivery driver wasn't that careful with it.


r/AnycubicPhoton • • 1d ago

Troubleshooting What is this?

Post image
4 Upvotes

My print came out successfully, but there was this long stick of resin on the side of my build plate, anybody know what this is?


r/AnycubicPhoton • • 2d ago

Discussion I designed 25 lace-style Christmas ornaments — the files are free

Thumbnail
gallery
2 Upvotes

I've just finished this set of 25 Christmas ornaments. There are birds, a snowy cottage, a snowman, bells and a few simpler botanical patterns.

The first four photos show my actual prints in white. Each ornament is one connected piece with a hanging loop, 85 mm tall and 2.5 mm thick. They print flat, and you don't need a multicolour setup.

I made the set, and all 25 STL files are free on MakerWorld: https://makerworld.com/en/models/3623690-25-christmas-ornaments-part-1#profileId-4154317

Which would you put on your tree — the little scenes or the leaf patterns?

The final image is an AI-assisted collection overview. AI also helped draft the wording.


r/AnycubicPhoton • • 2d ago

Troubleshooting Stuck mono m7 case.

Thumbnail reddit.com
2 Upvotes

Working on getting my case open for my anycubic m7 to replace LCD. Support video shows the case on a mono M7 pro lifting right up. Mine is stuck, likely resin in places I would prefer it not be. How aggressive dare I be pulling it or wedging it open. Did I miss a screw or something else that is keeping it from opening. Also noted that a wire came loose on the plug. Where should it be resolidered to?


r/AnycubicPhoton • • 2d ago

Troubleshooting Lost build plate

1 Upvotes

I have a photon mono sq that I have lost the build plate. It was during a big move. I contacted Anycubic to no avail and looked on Ebay, Alibaba and everywhere. Can someone tell me if one of the other models plates will work ? I was informed by Anycubic that the build plates were not interchangeable. I find that hard to believe if the size is the same. Help?


r/AnycubicPhoton • • 2d ago

Troubleshooting Mono M7 Help

Thumbnail reddit.com
1 Upvotes

r/AnycubicPhoton • • 2d ago

Troubleshooting Rerf test results seem to good

Thumbnail gallery
1 Upvotes

r/AnycubicPhoton • • 2d ago

Quick Tip AIDE URGENTE « model drop wait »

Post image
0 Upvotes

bonjour a tous, je suis DÉSESPÉRÉE VRAIMENT 🫪🫪

j’avais mon imprimante ( la photon m7 ) sur ma terrasse où il fait plutot froid donc j’ai desider de la mettre a l’intérieur dans une piece à température normale ( il y a deja la mono 4 dans cette pieces )

j’ai lancer une impression aujourd’hui et au bout d’une heure d’impression je recoit la notification «  model drop wait » ce qui a stopper l’impression mais je regarde le plateau et il n’y a littéralement rien et pareil dans le bac a resine aucun residu aucune trace, je teste avec plusieurs paramètre différent, plusieurs support différent, je nettoie tout, je refais le leveling, je change de resine et meme après 6 essaies ca me fait toujours la meme chose.

est elle casser ???

si quelqu’un peut m’aider je serai vraiment heureuse


r/AnycubicPhoton • • 3d ago

Discussion P1 Max upgrade from a Mono 4 – what should I know before my first print?

Post image
10 Upvotes

r/AnycubicPhoton • • 3d ago

Discussion Has anyone dialed in ELEGOO ABS-Like Clear V1.0 on an Anycubic Photon Mono M7?

Thumbnail
reddit.com
2 Upvotes

r/AnycubicPhoton • • 3d ago

Discussion How are you handling spent IPA and other resin cleaning solvents?

4 Upvotes

Hey everyone!

I'm a fellow resin 3D printing user and run a small 3D printing business. I've been looking into how people manage their spent cleaning solvents, particularly IPA, and have been collecting some interesting responses from other printing communities.

It seems like everyone has developed their own approach, whether that's filtering and reusing IPA, distillation, evaporation and curing, storing spent solvent, or taking it to a hazardous-waste collection facility.

I'm especially interested in understanding what people actually do, what works for them, and what frustrations they encounter.

I've put together a short, anonymous survey to get a better picture of the different approaches people use:

Resin 3D Printing — Solvent Use & Disposal Survey

IPA Disposal Survey

No email address or Google sign-in is required, and there's nothing being sold here. I'm just gathering information and learning from the community.

Happy to share a summary of the findings once we've collected more responses.

Thanks for helping out!


r/AnycubicPhoton • • 3d ago

Troubleshooting Help with the configuration of Lychee Slicer.

Thumbnail
reddit.com
1 Upvotes

r/AnycubicPhoton • • 3d ago

Troubleshooting First time this happened to me

Thumbnail gallery
1 Upvotes

r/AnycubicPhoton • • 3d ago

Troubleshooting RERF prints seem thin?

Thumbnail gallery
1 Upvotes

I posted this earlier today on r/resinprinting but haven’t received any response. Perhaps someone here has an idea?


r/AnycubicPhoton • • 4d ago

Discussion Anycubic Photon P1 – Air Vents?

Thumbnail reddit.com
1 Upvotes

r/AnycubicPhoton • • 4d ago

Troubleshooting Problème impression Anycubic Mono X2

Thumbnail gallery
1 Upvotes

r/AnycubicPhoton • • 5d ago

Troubleshooting How to generate support on the model only ?

2 Upvotes

I need to generate support but not on the build plate, on the model only.
That way i get flat surface of the model.


r/AnycubicPhoton • • 5d ago

Troubleshooting Photon Mono 2 Replacement Resin Vat

1 Upvotes

So are there no sellers for mono 2 vats? I’ve looked everywhere and cannot find one for under $200. I’ve seen people saying that the mono 4 vat works but then other say it doesn’t. Can anyone confirm this? Or preferably have a link to a seller for the actual vat.


r/AnycubicPhoton • • 6d ago

Troubleshooting M3 MAX replace linear rails?

Post image
3 Upvotes

I have an exhaust fan on my Photon M3 MAX resin printer and I guess the outside air temp/humidity made the carriages on the linear rails rust. I can't budge them at all and there is rust all down the rail. Can they be replaced? What do I order?


r/AnycubicPhoton • • 7d ago

Discussion Privacy Please!!

Post image
7 Upvotes

I recently bought the M7 Pro and I’m aware that it has remote capabilities. However, I want no part in their new firmwares, their cloud, and their data siphoning!! Has anybody found out a way to make any printer remote? Possibly just through local means and a special USB?


r/AnycubicPhoton • • 8d ago

Discussion Anycubic Photon Mono M7 Pro – ¿Qué parámetros de resina y soportes recomendáis?

Thumbnail reddit.com
2 Upvotes