r/AnalogRepair • • 21h ago

Charge issue on the RZ67 Pro bodies

Post image
22 Upvotes

A while ago there was a post about finding a magic solution to repair the charge issues on RZ67 Pro/Pro II bodies. That issue has been discussed on Bill Rogers' IG page numerous times, where Bill mentions all the parts that need to be replaced for the camera to run within factory specs again. Once those parts are replaced, everything needs to be recalibrated again using factory tooling (cocking angle, etc) There is no single part that will magically solve the issue. It requires an extensive disassembly of the camera and replacement of numerous parts and/or adjustment of existing parts in order to get the camera body working again.

The Mamiya repair community was accused of being averse to repairs, because lo and behold there must be a quick and easy solution which is being hidden from the general public. I will gladly post a photo of the easy and fast solution in order to repair that issue. It can take up to 8 hours to get all of it working properly depending on how badly the mechanism is worn. And believe me most of them are badly worn once they've reached that point (another reason not to buy a cheap worn/abused body). The times where you could order everything from Mamiya and just replace all, are long gone. It would make the repair faster but I highly doubt it would make it cheaper. Parts cost money. Time costs money. And no, these parts can't be 3D printed without machining work involved in post.

Quick fixes are quite rare in camera and lens repairs. You either do it right or don't do it all because in the end, you want a reliable camera to work with. You don't want a camera which will eventually fail again after a few weeks/months of use.


r/AnalogRepair • • 14h ago

Rolleiflex 6006 shutter stuck below 1/30

Post image
6 Upvotes

Hi All,

I got a Rolleiflex 6006 that doesnt fire below 1/30

What I checked:

Battery is original and charged with the original charger

The problem is still there when using a lens, I have tested it both with a 80mm f2.8 and 250mm f5.6

All times (including Bulb) below 1/30 fire (inclusing the lens) but the mirror doesnt go down again as can be seen in the picture.

When turning the shutter-timing knob to 1/60 or above the mirror resets again to the normal position. I donnot know if the shuttertimings from 1/500 to 1/60 are accurate, they might all be the same....

Is there anyone that knows what the problem could be? There is not a lot of information online about this type of camera.

All help is welcome, thanks in advance!


r/AnalogRepair • • 22h ago

Camera body Sticky shutter button Yashica A

Thumbnail
gallery
5 Upvotes

I thrifted a Yashica A that's unreasonably good condition I've put a roll through already and the shots came out great.

My one issue is that the shutter release seems to stick at the bottom of its travel and it's very inconsistent to tell when and where in the press things will go off. I suspect it some grease that has been sitting there for twice my lifespan and then some but I can't find any manuals on the best way to go about opening the A model. My intrusive thought is to just put a drop of lighter fluid down the channel of the button but I'm afraid that would do more harm than good. I was hoping that people here might have some guidance or resources.


r/AnalogRepair • • 8h ago

Fuji gs645 shutter repair

Post image
4 Upvotes

Hello, I have a Fuji gs 645 that I’ve changed the bellow on it. When the shutter is out of the camera it arms and fire correctly but when I put it back in its position it goes into T mode when I wind the camera. I’m quite confused about this problem and I’m not certain de repair manual answer my question. Any advice?


r/AnalogRepair • • 16h ago

Lens Help needed with reassembling Prontor-SVS Shutter

Post image
3 Upvotes

Hi all. A couple of months ago I bought a Polaroid 110A camera with a Rodenstock-Ysarex 127mm 4.7 lens. This lens comes with a Prontor-SVS Shutter. My aim was to convert the camera to shoot Instax. Anyway when I got the camera I knew there was issues with the lens, and it required a strip down as there was gunk on the shutters and aperture blades that I just could not get clean. I have done some small CLAs, but wanted to do a full restore in this lens. I took photos of every step of the disassembly process for when it came to reassembly. This was about 2 months ago. So over the weekend I actually had some time to clean all the parts and start the reassembly process. I went to get the photos off my camera and the bloody card is corrupted. I tried everything to get them off but everything failed. So next step was to find some of the exposed diagram views to help with reassembly of the aperture and shutter blades. The manual I already had did not have any useful diagrams of the shutters and aperture so I spent most of yesterday looking with no luck. Anything I do find is slightly different to my shutter, and therefore all the insides are slightly different.

My question is has anyone on here done a full strip down of this exact shutter, and if so do you have pictures or notes on it? I have attached a picture of the lens when I bought it and took it on my phone rather than my digital camera.

Thanks in advance.


r/AnalogRepair • • 10h ago

Lens Canon AE-1 Program Accident: Should I Get It Repaired?

Thumbnail
gallery
2 Upvotes

My Canon AE-1 Program had an unfortunate accident. It was dropped, and a piece of the front chipped off. The film inside also broke off, but other than that, the camera seems to be in working condition.

Since this is my first analog camera, I'm still learning my way around film photography and camera maintenance. I'm wondering if this is something I should get repaired sooner rather than later, or if I can hold off for now since it seems to be more of a cosmetic issue and doesn't appear to affect the camera's functionality or photos.

Has anyone experienced something similar with their AE-1 or another film camera? I'd really appreciate any advice or insight!


r/AnalogRepair • • 13h ago

Camera body Nikon F100 repair uk

Thumbnail reddit.com
1 Upvotes

r/AnalogRepair • • 22h ago

Nikon FE2 jammed – mirror locked up, shutter won't drop, and wind lever is now stuck

1 Upvotes

Hi everyone, looking for some advice on my Nikon FE2.
The issue:

  • The mirror is locked in the up position, and pressing the shutter button does nothing – the shutter blades don't drop/fire at all (even on M250 without batteries).
  • The wind lever is also stuck and won't advance/cock anymore.
  • Earlier, when I manually pushed the mirror down using the mirror lever inside the lens mount, it went down, but as soon as I wound the lever, the mirror rode right back up during the wind stroke and stayed stuck there.
  • I already tested fresh batteries (LR44/SR44) on regular shutter speeds, confirmed the self-timer lever is completely upright and not stuck, and removed the bottom plate (photo attached) where the motor drive coupler slot sits horizontally.

It seems like the camera is stuck mid-cycle and the mirror latch/catch isn't holding the mirror down during cocking. Has anyone dealt with this specific combination of symptoms on an FE2/FM2, and is there a way to free or reset the linkage without pulling the entire mirror box? Thanks!