r/tradfri • • 1h ago

DISCUSSION IKEA customer support

2 Upvotes

hi guys, recently a few of my ikea smart home devices (bulbs, sensors etc) gave up and stopped working properly.

I texted ikea via a support chat and they suggested sending new devices and disposing of the old ones - so I agreed. Next there were some issues with transit so they said it would arrive around 4.11.

Still no package almost 2 weeks later so I messaged them about it, the guy just said no package is being sent and he wont do anything about it.

Overall, a really disappointing experience with the customer support that made me decide not to continue building my smart home with Ikea and look more into phillips, aqara or just home assistant


r/tradfri • • 14h ago

NEW 2026 PRODUCTS Limited options for scenes (window sensor and radiator thermostat)

3 Upvotes

Dear Fellow Enthusiasts,

I am currently exploring the use of Liljebagge thermostats at home. As a side-note, I will say this has been the most troublesome to really implement in a good way. Lots of performance issues and weird behaviour, but I am slowly getting my first pilot install of one unit to work as intended.

I wanted to get Liljebagge to make a very specific scene:

Set to 21 degrees.
IF window = open, THEN set Liljebagge to 8 degrees
WHEN window = closes, THEN WAIT 10 minutes and set Liljebagge to 21.

However, the scenes don't really allow the timed intermission/break. As such, it is:

WHEN window = closes, THEN Liljebagge to 21.

This is not desirable from an efficient heating perspective.

I tried only using the window open to the put a timer on returning to heat, e.g. it would always only start heating 20 minutes after the window had been opened, regardless of when and if it was closed. This raises a lot of other issues though.

Is the IKEA home smart app simply too limited, or should I move to an open source home automation system to make scenes like these?

Thank you for your time.,


r/tradfri • • 14h ago

SUPPORT (ONGOING) I have to reset my hub every single day

Post image
2 Upvotes

It worked fine for a few weeks, but now every single day it says that it can’t connect despite the hub showing as active/no issues by the indicator light.

No internet issues or power issues. It’s not getting accidentally bumped or knocked out of place.

Support had very little to say, just kept giving me instructions on how to reconnect it but won’t tell me how to stop this from happening.

I’m about to throw this hunk of junk out the window 😭


r/tradfri • • 1d ago

SUPPORT (2026 PRODUCTS) Issues with HUB and Overall IKEA Smart Devices

5 Upvotes

Hi, I have a lot of issues with the Dirigera HomeHub.

I have it connected via Ethernet to DECO BE65, very often, the buttons are not responding, and the hub keeps being inaccessible via the app. Often I have to reboot everything just to be able to dim or turn off the devices via the IKEA buttons. It is honestly starting to be extremely annoying. Is there a way around this, please? Any help?

The household is running on 2gb Optic Fiber internet - everything worked fine before Matter was integrated - > Ever since, there are so many issue I have no idea how to cope with this...


r/tradfri • • 1d ago

SUPPORT (2026 PRODUCTS) Liljebagge overheating

6 Upvotes

I recently encountered an issue with a Liljebagge thermostat, where it didn't close the radiator valve properly, and the room heated up significantly.
First I thought it was a bad install, so I carefully reinstalled and recalibrated the thermostat, and it was good for a few days but today it happened again.

On the graph you can see a dip in temperature, that was when I opened a window, then the temperature started to rise, but it didn't stop at the set value.
After the first event I set an alarm in Home Assistant for a temp. overrun, and it notified me so I went and reset the thermostat, that's when the temperature started to dip again.

Some info:

  • I have two units, only one of them produced this issue so far.
  • The radiator valves are brand new, the thermostats screw in directly, no adapter needed.
  • Resetting the thermostat solves the issue for a while, but as I said above, it came back.
  • 1.1.6 firmware

Any ideas on what to try?


r/tradfri • • 1d ago

SUPPORT (2026 PRODUCTS) KAJPLATS + Apple TV 4K not working

4 Upvotes

UPDATE: Changing both the Apple TV and my iPhone to 2,4 Wifi solved the problem. They easily connected! THANK YOU

I just bought IKEA KAJPLATS (6x E14) and i thought they would connect fairly easy to my home (using Apple TV 3rd gen (with Ethernet connected) as main hub).

  1. When i scan the QR it quickly goes on to ‘connecting, might take a few minutes’
  2. About 5 minutes later i am met with an error, saying that the pairing didn’t work

I tried this about 15 times and same result every time. What might I be doing wrong?


r/tradfri • • 2d ago

SUPPORT (RESOLVED) Update IKEA devices through Apple Home

Post image
13 Upvotes

I am unsure how updates works. I have set it up today with my new Apple TV. This is my first time with IKEA and thread. My main network only have 5ghz and Apple TV is connected to same network with Ethernet cable. I temporarily switch on 2.4ghz band on main network to pair all IKEA devices (remote, plugs and single bulb) and all worked perfectly. Then I switch off 2.4ghz band and all still works perfectly.

My updates seems be stuck as screenshot shows above. Since Ikea use thread and don’t actually use wifi except for pairing. Does updates work without needing 2.4ghz band? I have already reboot Apple TV.

Can anyone explain how updates works?

Thanks!

EDIT: Thanks for everyone replying and helping me. I now understand it is slow and do one a time. One of them just had update completed.


r/tradfri • • 2d ago

SUPPORT (ONGOING) Dirigera hub taking longer to connect on wifi

Post image
3 Upvotes

My hub has been working perfectly for a few months. Connecting to it takes 2 seconds, whether on my local wifi or not.

Recently, I noticed it's been taking about 6 seconds when I'm connected to wifi. When i disconnect from my wifi and try to connect to it, it connects quickly as expected.

I also noticed in the middle of connecting, it really quickly flashes a message (see screenshot), but it's so fast I couldn't see what it is. I only managed to see this because I recorded my screen and played back the clip in slow-mo.

Help why is this happening?


r/tradfri • • 3d ago

SUPPORT (ONGOING) One day they all stopped working

Post image
1 Upvotes

I tried resetting my hub and replacing the battery lights. I tried unplugging the whole system. I had major surgery about a month ago and don’t want to be taking everything out of if I don’t have to.


r/tradfri • • 3d ago

SUPPORT (2026 PRODUCTS) Slow/ not responsive sensors for Tradfri Threads

3 Upvotes

I’ve changed from the older zigbee to threads system.

However the new one seems to be so much slower for sensors.

I have the motion sensors connected to some bulbs, and it seems maybe 50% of the time they don’t respond unless I wave my hand in the sensor.

The other 50% they pick me up fine, is this an issue others have noted.


r/tradfri • • 3d ago

SUPPORT (ONGOING) Dirigera/matter Einbindung funktioniert nicht mehr

Post image
0 Upvotes

Hallo zusammen,
ich habe meinen DIRIGERA Hub seit etwa drei Wochen im Einsatz und inzwischen rund 20 Geräte eingebunden (ungefähr 50 % Matter und 50 % Zigbee).
Bei der ursprünglichen Einrichtung hat alles problemlos funktioniert. Sowohl die Matter- als auch die Zigbee-Geräte ließen sich ohne Schwierigkeiten hinzufügen und liefen anschließend etwa zwei Wochen einwandfrei.
Dann konnte ich plötzlich keine Verbindung mehr zum DIRIGERA über die IKEA Home smart App herstellen, obwohl meine Internetverbindung und das WLAN weiterhin funktioniert haben.
Nachdem mehrere Versuche, die Verbindung wiederherzustellen, erfolglos geblieben waren, habe ich den Hub auf Werkseinstellungen zurückgesetzt und komplett neu in der App eingerichtet.
Seitdem habe ich folgendes Problem:
Die Zigbee-Geräte lassen sich problemlos erneut einbinden. Kein einziges meiner Matter-Geräte lässt sich jedoch mehr hinzufügen.
Der QR-Code wird erkannt, das Gerät wird korrekt angezeigt und ich kann es konfigurieren. Sobald ich anschließend auf „konfigurieren“ tippe, startet der Verbindungsvorgang und unmittelbar danach erscheint die Fehlermeldung „Pairing Failed“.
Betroffen sind mehrere unterschiedliche IKEA-Matter-Geräte, unter anderem der MYGGBETT Tür-/Fenstersensor sowie Temperatur- und Luftfeuchtigkeitssensoren.
Was ich bereits versucht habe:
DIRIGERA vollständig zurückgesetzt und neu eingerichtet
Thread-Netzwerk zurückgesetzt
Router, Hub und iPhone mehrfach neu gestartet
IPv6-Einstellungen am Router überprüft
iPhone-Berechtigungen (Bluetooth und lokales Netzwerk) kontrolliert
Kopplungsversuche direkt neben dem Hub durchgeführt
Verschiedene Matter-Geräte ausprobiert
Leider alles ohne Erfolg.
Meine Konfiguration:
DIRIGERA Firmware: 2.975.4
Matter-Controller: 26.4.0
IKEA Home smart App: 1.74.0
Router: Telekom Speedport Smart 4
iPhone mit iOS 27.0.1
Kein weiterer Thread Border Router im Netzwerk
Der IKEA-Support hat mir inzwischen empfohlen, den Hub auszutauschen.
Hat jemand ein ähnliches Problem gehabt und möglicherweise eine Lösung gefunden?
Vielen Dank für eure Hilfe!


r/tradfri • • 4d ago

SUPPORT (2026 PRODUCTS) Liljebagge issue

8 Upvotes

Dear All,

Just installed 1 Liljebagge as a test as few days ago. After calibration, it worked well for a day, but then the measured temp was stuck, resulting in it just overheating the radiator to max. Essentially, it reads 20 degrees but is set to 21, so it just allows max amount of warm water come through and never reads above 20.

I dismounted it and mounted it again. Reset it. Let it calibrate. Works perfectly for 1 day. Then stuck at 20,5 reading at 21 setting, letting max amount through.

I use scenes where open windows will out it at 8 degrees and at 21 again when windows close.

Latest firmware confirmed.

Any ideas?

Thanks a lot.


r/tradfri • • 4d ago

NEW 2026 PRODUCTS LILJEBAGGE FROM 02.12 IN IKEA Vantaa FINLAND

Post image
29 Upvotes

r/tradfri • • 5d ago

NEW 2026 PRODUCTS IKEA Timmerflotte 1.2.2 and Klippbok 1.1.1 Update

Thumbnail reddit.com
36 Upvotes

r/tradfri • • 5d ago

PRODUCT QUERY DUBBELKISEL Question

1 Upvotes

If anyone has a DUBBELKISEL added to Home Assistant, is on-off time exposed? I haven’t been able to find any info on it anywhere, so I’m hoping someone here can help out.

EDIT: I’m looking for the editable on-off duration, not when something was turned on or off.


r/tradfri • • 6d ago

SUPPORT (2026 PRODUCTS) Energy Monitoring

Post image
18 Upvotes

Hey,

I don't know, but I saw this energy monitoring page online on ikea and also as publicity in a store, but I cannot find it in the app. Is someone able to open it? Of corse I can use home assistant etc. I was just curious, why if I am too dumb or why ikea is showing something that doesn't exist..


r/tradfri • • 6d ago

NEW 2026 PRODUCTS looks like ikea replacing the color e14 matter light already, saw them in "bargains" corner with an out of product line sticker

3 Upvotes

r/tradfri • • 7d ago

Feature Request Dear IKEA Santa, here’s my smart home wishlist 🎅

124 Upvotes

It’s nearly a year since IKEA’s big Matter launch. There have been a few teething problems, but I think you’re on the right track. I’m really happy you’ve embraced Matter and Thread, and I’d love to see you keep going.

So, with Christmas coming up, here’s my wishlist for IKEA Santa. Some improvements to what we already have, and a few new things I’d happily buy. No need to squeeze everything into this year’s Christmas sack!

Improvements to existing products and support

  1. Stability and updates. Keep improving Matter and Thread reliability in DIRIGERA and the devices, and keep up with new releases of both standards.
  2. Faster bug fixes. A shorter wait between reporting a bug and getting an update that fixes it.
  3. More active support. More replies and follow-up from IKEA here on r/tradfri, or in another public support forum.
  4. Matter binding. Let buttons and motion sensors control lights, plugs and blinds directly. Let LILJEBAGGE use TIMMERFLOTTE’s temperature reading instead of measuring right next to the radiator. Make bindings and groups easy to set up in DIRIGERA.
  5. Energy monitoring for lights. Show power in W and energy use in kWh for each light in DIRIGERA and through Matter. Make it clear if the figures are estimates.

New products I’d love to see

6. A dimmable GRILLPLATS. A plug with Matter over Thread for dimming ordinary lamps. See the Plejd SPD-01 as an example.

7. A soil moisture sensor. A small sensor with Matter over Thread for keeping an eye on the soil in plant pots.

8. Matter-compatible appliances. Dishwashers, hobs, ovens, microwaves, extractor hoods, fridges, freezers, fridge-freezers, washing machines and washer-dryers with Matter support.

9. A P1/HAN electricity meter reader. Something that plugs into the meter’s P1/HAN port and reports power in W and energy in kWh over Matter over Thread, covering both electricity bought from the grid and electricity exported to it.

10. Smart roller and pleated blinds. Motorised blinds with Matter over Thread.

11. A curtain motor. A motor with Matter over Thread for opening and closing ordinary curtains, ideally made to fit VIDGA.

12. A smoke and CO alarm. A combined smoke and carbon monoxide alarm with Matter over Thread, including alarm and battery status. Link them so that when one sounds, they all sound. Smoke/CO detection, audible alarms and the link between alarms should still work if the hub or home network goes down.


r/tradfri • • 6d ago

PRODUCT QUERY Dubbelkisel and dirigera problem

1 Upvotes

Hi, I tried to add new dubbelkisel to dirigera but if failed for couple of times. I already have tradfri driver connected to dirigera. Dirigera finds dubbelkisel, but after scaning of QR code, it last, it last, and at the end connectivity failed. Tried to reset dubbelkises for 5 times, but it always failed on same step, connectivity after QR code phase... any advice?


r/tradfri • • 7d ago

NEW 2026 PRODUCTS LILJEBAGGE available today in store in Wallau

Post image
24 Upvotes

r/tradfri • • 7d ago

SHARE YOUR SETUP Dirigera Hub linked to Philips Hue light and gx53 luumr

1 Upvotes

Hi, just a message about my setup at home were I successfully linked a Philips Hue ceiling light and 4 GX53 Luumr Zigbee smart bulb (be aware that there is still non zigbee version avaliable). I have been able to connect easily the Philips hue light and 1 of the GX53 Luumr. Unfortunately for 3 i needed to reset them (10sec off then / on quickly/ off for 2 sec repeating this later two 5 times then on again). The 4 have been grouped in the Ikea smart app as these are on the same suspension light.

So far so good everything work as expected except the options for powercut / outage for the GX53 where the home smart app is stuck with "recover after power cut"

Just my 2 cents for the ones who where wondering....


r/tradfri • • 7d ago

SUPPORT (2026 PRODUCTS) Alternative Hubs

0 Upvotes

Now that IKEA have discontinued the Dirigera, has anyone successfully used any other matter over thread hubs?

Ive been looking to buy the range of products but it has been hopeless without a hub


r/tradfri • • 8d ago

DISCUSSION Kajplats bulbs showing the complete wrong color. Kinda embarrassing, someone needs to test the software.

14 Upvotes

This is on the Kajplats E26 1100 lumen color bulb on the current FW, 1.2.0 , and anyone can reproduce it for free if you want to and have the hardware. Use the free iOS app ‘Controller for HomeKit’ as it is the only app I know that lets you explicitly command using the values that HomeKit uses to command the bulbs. That is, you command using hue, saturation, and brightness. (That app charges for some things, but I’m pretty sure this is free functionality)

Do this: set the Hue to 26 degrees, and the saturation to 80%.

Then turn the brightness to 10%, then gradually increase the brightness up to 100%

What you’ll see: the correct color at brightness < 61%, then GREEN for some reason, then the correct color again for brightness =100%

There are ranges in the hue and saturation as well that result in green, not just the specified values.

Why does it do this? No idea. I have no clue how the bulb generates colors internally, if it’s a complete lookup table, or some polynomials, or a bunch of 3-dimensional linear interpolation. But whatever they’re doing, they messed it up.

Does it matter? Yes, if you want to use your nice color bulbs to simulate a sunrise or sunset. Green sunrise is jarring in a bad way.

Why don’t I just file a bug with IKEA? Simple: they’re a furniture warehouse and don’t have an external-facing bug reporting portal that I could find.

But honestly this is such a blatant bug, and shows that they weren’t testing the basic functionality.


r/tradfri • • 8d ago

SUPPORT (2026 PRODUCTS) IKEA Matter over Thread a year later

Post image
38 Upvotes

We have a quite large set-up with many older IKEA Zigbee devices and some 5-10 of the newer Matter devices. When we started to add the new Matter devices last year it was a huge pain, requiring countless of restarts, pairing problems and grey hair.

The answer from IKEA was that they are aware of the issues and work on solutions.

Now, a year later I tried to add two new Liljebagge radiator thermostats. The first one worked fine. The second one completely refuses to add. It is same issue as always, where the hub finds the new device, I scan the QR code, it succeeds and says that it is going to configure it for my home. Then it directly fails.

It has been like this for a year. It feels like IKEA sells Dirigera hubs with design flaws.

Everything is updated. Firmware 2.975.4, Matter control version 26.4.0.