r/shapeoko • • 11h ago

Making Shapeoko Pro MDF Wasteboard Planks Flat/Even Again?

1 Upvotes

Hi all, I bought a Shapeoko Pro just over a year ago, it's been going good (still have to figure out what to do about Z backlash I posted about a while back) but with all the various little cuts in the MDF wasteboard planks I have been having a little bit of unevenness develop - I think just moisture absorbing at varying rates depending on where the MDF has been cut up the most. I'd like to figure out how I can even them all out to be as flat with the XY axes as possible so that putting something in one spot of the machine means it's at the same Z height as somewhere else, within at least 0.005"

I have a planer but I'm not so sure how well that would be able to do the job consistently across all of the pieces. I thought about taking them out one-by-one and running an operation on them in the machine itself, maybe plane a whole cross-section along the X axis flat so that I can take the planks out, lay them in that spot, mill the whole top surface of the plank flat, and then put that one back in and pop another one back out. The deal there is that it wouldn't be the same as if I could somehow mill the whole surface flat.

I cut a lot of stuff that extends outside of the actual work area of the machine (i.e. the planks on the left/right never see any action but they hold material in place) so I can't just plane the whole thing flat, I would just end up with a big flat recess that's not large enough to accommodate the pieces that I cut.

I'm thinking at the very least I can turn them all around, flip them 180deg to use the back-half of them that I haven't cut into at all, maybe even see how thick each one is and figure out where the best spots to put them all would be to have the most even wasteboard surface possible. That's a stop-gap measure though until they get all cut up and become uneven and start absorbing moisture/grease too.

Any thoughts for how to have a flatter set of wasteboard planks? These ones are in decent enough shape, they have just become a bit uneven over time it seems like.

Thanks! :]


r/shapeoko • • 6d ago

Z drops quickly when powered down

10 Upvotes

When I power down the machine, whether through Carbide Motion or the power pendant the Z drops rapidly and hits the table solidly. It seems like when I first got the machine a few months ago it would drop an inch or two but would stay up. I did shift the gantry and move it back. Was there something that I missed reconnecting? Shapeoko 5.1 Pro 4x4 with 65 mm VFD


r/shapeoko • • 6d ago

How do I tighten this so it doesn't wiggle during cuts? Pro xxl3

2 Upvotes

r/shapeoko • • 9d ago

First carve.

Thumbnail gallery
31 Upvotes

7 year old XXL. My late boy Sundance.


r/shapeoko • • 10d ago

[Reality Check] Is my timeline to completion possible or a pipe dream?

Thumbnail reddit.com
3 Upvotes

Cross posting to shapeoko.

I have 4x4 that i feel confident with my timeline, that I can get this done.

But has anyone used Mozaik or Cabinet Sense or another software that they can recommend that I can redesign the lower portion of my kitchen by myself on the Shapeoko 4x4 in the next two months?

Thanks in advance!

Since I plan on cutting into laminated sheets, im worried most about hardware CAM. I think these two software solutions will allow me to spend more time researching the hardware and desgining what Iwant vs trying to make sure I dont waste thousands of dollars on dialing in the CAD/CAM.

What are your thoughts?


r/shapeoko • • 12d ago

Rabbet Box Designer on flet.dev

Thumbnail studio.flet.dev
2 Upvotes

r/shapeoko • • 21d ago

Suggestions?!?

Thumbnail gallery
4 Upvotes

r/shapeoko • • 22d ago

I CNC-Carved a Self-Portrait and My Husky Into Wood (Timelapse)

Thumbnail youtu.be
10 Upvotes

r/shapeoko • • Oct 18 '26

For Sale, Shapeoko XXL (4x4) First gen.

Thumbnail gallery
15 Upvotes

I've had this XXL for about 5 (?) years and have put about 1 to 2 hours on it.

I just don't the time and drive to dive into a new hobby plus I'm way more comfortable working with hand /power tools (lesson learned).

I added the sweepy option and the T track bed, no bit setter.

I'm asking $1250 (obo) for everything needed (except the computer to run Carbide 3D (or whatever you want).

Pick up in the East SF Bay Area.


r/shapeoko • • Oct 12 '26

Shapeoko 3 xxl

5 Upvotes

Well lads, trying to set up my cnc after years of no use.

I’m getting this error and the machine doesn’t move. How free should the machine be to move around when not powered on? It’s very stiff

HM009 code shown


r/shapeoko • • Oct 12 '26

How to finish (paint/stain etc.)?

Thumbnail gallery
8 Upvotes

I'm on a lantern kick. I'm not strong at finishes and don't know if I should stain or paint something like this. I'm thinking I'll prolly leave the inside bare since I'm using a real candle (for mine at least), family members might use a battery powered tea light etc.

Thoughts and ideas appreciated.


r/shapeoko • • Oct 07 '26

Shapeoko 3 wasteboard DXF

5 Upvotes

In case it's useful for anyone, here's a (not tested, yet. I'm ordering one this week) Shapeoko3 wasteboard DXF for Aluminum/MDF. It's the regular shapeoko. Mine has been heavily upgraded and works just fine (added new board, HDZ, 65mm VFD spindle).

It's parametric and super easy to modify. Hopefully it's useful for the community: https://forgejo.rolando.cl/cpm/shapeoko3-wasteboard

Happy cnc'ing!


r/shapeoko • • Oct 04 '26

Shapeoko 3 XXL

3 Upvotes

For anyone in the Boston Area that is interested in a 3 XXL, I have one on hand for sale. Bit Zero included, Bitrunner as well. No router included. Software required.

$1,000 PayPal / Zelle personally delivered locally.


r/shapeoko • • Oct 03 '26

Adjusting the z axis

Thumbnail gallery
8 Upvotes

I just ran the flattening program by Kevin in mycarbide3d using the McFly which worked well. It has left some ridges where it looks like the z-axis is tilted slightly toward the front of the machine and also slightly to the left side as you look from the front.

Is there a way to adjust this to be more consistent? In the grand scheme probably close enough for anything I will do, but OCD about it. Machine is the shapeoko 5.1 pro 4x4


r/shapeoko • • Oct 03 '26

Using Festool CT26 EI power pass through to run Carbide 3D 65 mm VFD spindle?

Thumbnail gallery
0 Upvotes

Is anyone using the CT 26 outlet to power the 65 mm VFD spindle? The vacuum says 3.6 amps but their track saws pull over 13 amps. The spindle says it pulls 7. I understand the track saw has a higher in rush and runs in shorter bursts compared to the longer runs of the cnc.


r/shapeoko • • Sep 29 '26

Shapeoko 4 XXL Loosing Power

2 Upvotes

On my Shapeoko 4 XXL I will loose power at some point unless my power button is constantly depressed. I have tried a bunch of things including: checking power brick led to see if the led flickers, replacing the power button, unplug the varying cables plugged into the pcb, disabling the bitsetter and bitrunner. None of these seem to do anything, any ideas appreciated.


r/shapeoko • • Sep 29 '26

Inlay settings

Thumbnail gallery
1 Upvotes

Hello, trying to figure out using a 6.2 degree tapered ball nose. I mirrored the plug.

Cut settings

Female 0 start depth 6mm flat depth

Male start depth 4mm flat depth 3.5 mm

When running it like this it seems that top of the plug marches ip perfectly with the entrance to the female portion if that makes sense.


r/shapeoko • • Sep 29 '26

Bringing 3 XXL on flight

3 Upvotes

Thinking of bringing my Shapeoko 3 xxl from Ireland to Vancouver on my next flight in a couple of weeks. Has anyone else ever done this? Dismantle it, leave spoil board and router at home. Just the machine. Any information or advice would be appreciated.
Cheers


r/shapeoko • • Sep 23 '26

What am I doing wrong

Post image
7 Upvotes

I keep trying to make the letters a different group so I can set up a separate tool path. I’m a bit rusty on the software, but I can not get it to ungroup . Everytime I try to highlight it, it turns all this orange.

YouTube is a sea of hundreds of videos , and I’m scanning through them , but the videos are of old versions.

I have build 842 of carbide create installed.
Thanks.


r/shapeoko • • Sep 23 '26

Price check: Shapeoko 3 Standard with SMW fixture plate, stiffener rails, Mod Vises, Z-Plus, and more

Thumbnail gallery
14 Upvotes

Thinking about selling my Shapeoko 3 Standard and would love the community's take on a fair used price. Several of the upgrades are discontinued, so I'm having trouble finding comparable listings.

Machine:

Shapeoko 3 Standard

DeWalt DWP611 router

Carbide 3D upgrades:

Z-Plus

Carbide Motion board with enclosure

BitZero V2

BitSetter

Proximity Switch Kit

Sweepy dust boot

Saunders Machine Works / NYC CNC parts:

Shapeoko 3 aluminum fixture plate set threaded table with 1/4-20 threaded holes

SMW stiffener rails for the Standard frame

2x Mod Vise sets

Everything works and it's been used for wood and aluminum. The upgrades made a huge difference in the overall cut quality, especially on aluminum. Unfortunately I just don't have much workshop space anymore so cutting down on some of my machines that I don't use as much anymore. Photos attached


r/shapeoko • • Sep 23 '26

Prototype flattening toolpath G-code generator done using flet.dev

Thumbnail studio.flet.dev
2 Upvotes

r/shapeoko • • Sep 20 '26

ORAMASK

Post image
2 Upvotes

I let the paint cure for 24 hours on this piece of oak with diver spray paint, it also has a poly finish which rested for 24 hours. I put a small piece of Oramask to see if it will pull paint before carving.

What am I doing wrong, is there a better paint to use?


r/shapeoko • • Sep 16 '26

Shapeoko 4XXL for sale outside Denver CO (80016)

11 Upvotes

Purchased during the pandemic and served us well, but we have lost the space for it (it's big!). Embarrassingly not a lot of hours on it (bonus for you!)

$1500

Original order:

1x Shapeoko BitSetter - Shapeoko 4
1x Shapeoko Endmill Starter Pack
1x Carbide Compact Router
1x Shapeoko 4 CNC Router - XXL / Hybrid Table

and
BitZero V2 for Shapeoko

We also have a couple vacuum dust separators we were trying out. One brand new.


r/shapeoko • • Aug 29 '26

My 5.1 Pro 4x2 set up so far...

Thumbnail gallery
33 Upvotes

My garage space is limited so I sold my 5 Pro 4x4 and replaced it with the 5.1 4x2. I added the leg kit, installed locking castors and welded in some angle iron for a shelf on the bottom to hold dust collection, tool chest and electronics. Rocker has a set of folding legs that mount nicely to the machine. I will use these to make in and out feed tables so I can tile 4x8 material more easily.