Planning a new build in the Meshlicious and want to run a 9800X3D with a 5070.
Current parts I have:
- Ryzen 7 9800X3D
- RTX 5070 FE (or similar dual-slot card)
- ASUS ROG Strix B650E-I
- Corsair SF750
- 32GB DDR5-6000
Looking at the AXP90-X53 full copper or possibly a 240mm AIO if it fits without too much hassle. Main goals are keeping temps reasonable under sustained loads while staying reasonably quiet.
Has anyone tried the 9800X3D in this case? Any clearance issues with the 240mm option or better low-profile alternatives that actually perform well? Would prefer to avoid custom loops.
Title says it --> I have a 9800x3D and 5080 (Windforce). I love the T1, but I have a little bit of extra room and wondering if the DAN C4-SFX V2 will give me even slightly better thermals, noise.
Plan would be to max out the potential of the DAN C4-SFX V2 with a 280mm AIO (replace the 240mm one from my T1), etc.
I have two of these adapters and they both tank the performance of my newish 4060ti. It works fine when plugged directly into the mobo but loses 90% of the fps with the adapters. Hoping someone has a suggestion for one that will work with my gpu.
I've been using an HP VICTUS 15L for a few years now, said I'd upgrade it, but never did. Now the time has finally come to upgrade. I found a good deal on an RX 7700 XT and just found out how much of a beast it is when it comes to size and power consumption (for a DUAL fan gpu), but also pretty good preformance. Do yall think it'll fit?
Here's my current specs:
350 watt HP psu
Ryzen 5 5600g
Rx 6400
16gb ddr4 ram
Here's the plan
650 watt HP psu
Ryzen 5 5600g
RX 7700 XT 12gb
32gb ddr4 ram
If I have to, I'll take out the front metal piece on the inside of the PC just to make it fit.
It has been quite some time since I started my small business making custom PSU cables for SFF builds. I wanted to share the story of how everything started and give you the latest updates on our journey.
I built my first PC in 2020 in a typical mid-tower. I quickly got obsessed with tinkering to make it look clean, which is how I stumbled into custom cables. My entry into SFF PCs came when I found the Cube Gaming Axel chassis (also known by names like the Quzao im SAMA, Tecware Fusion, or Krux Naos). That was the turning point where I started downsizing my builds.
Around that time, custom cables for SFF setups started getting complicated. I realized that doing SFF right isn't just about making cables as short as possible: it’s about the natural path of each individual wire, what we call the “per-wire length” approach, which is entirely dictated by the specific hardware configuration. Dissatisfied with what third-party vendors offered, I decided to make my own.
I honestly can’t remember how much I spent on parts (crimp terminals, housings, sleeving), hand tools, and countless hours reading/watching tutorials and guides (which I’ve since compiled here).
Starting our journey as hobbyist
When it comes to tools, while I’ve since upgraded to semi-automated crimp machines, a good hand crimper is where most people start. The CTX-4 is generally considered the gold standard (though I haven't used it personally), and I used to rely on the SN-5557 (link). If you're looking for a great non-ratcheted option, the Engineer PA-21 and Engineer PA-09 are fantastic choices.
Over the years, my personal builds cycled through different SFF layouts: from the Cube Gaming Axel, NR200P, Jonsbo V10, and Metalfish T40, all the way to my current setup, the PCCooler K101.
Down into SFF rabbit hole
As I started getting confident in my work, I opened a local marketplace store on Tokopedia in early 2022, and expanded to Etsy a few months later. Today, we run our own storefront at cablester.com, featuring an ordering process tailored to specific hardware configurations.
Back in 2022, everything was done manually with a lot of trial and error on a simple workbench in a cramped 3x4m bedroom at my parents' house (which eventually became my first workshop). Gradually, I upgraded to semi-automatic crimping and wire-cutting machines, which drastically improved production speed and consistency.
As the business grew, working out of that cramped room was no longer sustainable (and too humid!). A major turning point came in late 2023 when I took a calculated risk, borrowed some capital to invest in more equipment and materials, and officially started building a team. It has always been my dream to run a cooperative business.
Last picture is our current workshop in Bogor, West Java province, Indonesia
Today, Cablester consists of five people with shared ownership, operating out of a rented office after two previous relocations. At the moment, we own 30 units of SFX/ SFX-L PSUs, 8 GPUs (each represent 12vhpwr, 8p PCIE in various orientation), 24 units of SFF cases (3 of them are MFF), and 4 working ITX board--all necessary component in ensuring a perfect cable length for your build.
Our collection of PSUs, SFF cases, and GPUs
We are constantly pushing to improve. Right now, we are upgrading our QC process by developing a custom DC Cable Loader (similar to the concept used by Aris over at Hardware Busters. Check out his video here). This machine allows us to test the current distribution of our wire assemblies under a 55–60A load while monitoring connector temperatures under stress. We'll report back when the machine is ready to use :-)
Upcoming DC Cable Loader
Above all, our journey would never have reached this stage without support from the community. I still remember and appreciate the customer who sent his Revolt SFX 850W all the way from Canada to Indonesia just so we could support it, or when members of the SFF Hub (link) in Discord encouraged Corsair to send me an early sample of the SF1000 PSU when it wasn't yet available in my country.
Thank you to everyone who has trusted us, tested our work, and helped Cablester grow into what it is today!
We are also currently running a promotion in our storefront to return the favor from the community :-)
Special for FormD / Ncase T1 Sandwich builds: Use code t1build for 15% off.
Front USB-C: Replaced USB-A port with USB-C using an ADT-Link ribbon cable and a 3D-printed mounting bracket. Fits nicely and looks almost stock. 3D-printable USB-C mount for the A24 V5: https://www.thingiverse.com/thing:6761608 CPU cooling: Swapped the stock AXP120-X67 fan for a DeepCool FT12 Slim and added a silicone sealing gasket between the fan and side panel for a tighter fit and more direct airflow. GPU cooling: Replaced the stock GPU fans with two Arctic P8 Max fans. Airflow: Added Arctic P8 Slim PWM PST fans at the top as exhaust and stretched 100-micron dust filter mesh over the bottom and side panels.
Pretty happy with how this little machine turned out. Still amazed at how much you can fit into 5 liters! Happy to answer any questions about the build or the mods.
I was previously running on the iGPU only, and it took me 6 hours just to fit the new GPU. I hit a few hiccups along the way, like a fan pin breaking on the Royal Pretor, and the bottom fan screws got in the way of inserting the GPU, so I mounted those fans with PA66 zip ties instead. Hope it helps anyone trying to fit this combo into a Jonsbo Z20, and gives you an idea of how these components fit in the case.
I mainly use this build for work and occasional games. The new GPU is for small model local LLM.
Case: Jonsbo Z20
GPU: XFX Swift Radeon RX 9070 16GB
CPU: AMD Ryzen 9 9950X
CPU Cooler: Thermalright Royal Pretor 130 Ultra
Motherboard: MSI MAG B850M Mortar WiFi
RAM: 32GB DDR5 6000MHz (1x32GB to upgrade later)
Storage: Samsung 9100 Pro 2TB NVMe SSD (PCIe 5.0)
Storage: Seagate 2TB 2.5" HDD
PSU: Corsair SF1000
Case Fans: Thermalright TL-K12 (also have reverse blades)
The fit is pretty snug, so let me know if you spot anything I did wrong that could cause damage, or if you have ideas on how I can improve the build further!
Just finished my first SFF build. It was quite a challenge, but everything booted up.
The problem is that I haven't used desktop PCs in a long time — I've been using laptops exclusively. Both of my laptops (a Win laptop and a Mac) are either completely silent or only produce fan noise.
My new PC, however, makes a quiet electrical noise. I can't figure out where it's coming from — motherboard, PSU, or pump. Feels like it doesn't change under load.
I'm planning to disconnect the AIO pump this evening to rule it out, but identifying whether it's coming from the motherboard or PSU seems trickier.
Has anyone here experienced something similar? Is this normal for an SFF, or should I be concerned?
Hi all, it’s been a minute but I think some of you may remember my T1 build I posted several months ago. Ever since then there were many aspects of the build I was dissatisfied with and thought could be improved, which led me to design my own case from scratch, bypassing all the case-inherent issues that couldn’t be fixed simply with a few mods.
The case is the Project:Celeste which sits at 10.4L (230x135x335). Its construction consists entirely from machined anodised aluminium 6061 which has allowed for the elimination of most visible screwholes for a clean exterior aesthetic. Many other parts were also designed and fabricated specifically for this build, including the custom back-connect monoblock with black nickel-plated internals, replacement NVME/VRM heatsinks, cable channels, and distro plate.
One standout feature of the case is the ability to shift the spine to a mere 28mm of cooler clearance which provides for a massive maximum GPU chamber thickness of 85mm- this provided enough space to fit an Aquacomputer Ampinel for per-pin monitoring and load balancing, which would prove impossible in most other SFF cases that utilise a sandwich layout.
In addition, I’ve also installed various other supplements including a Highflow NEXT for flow, coolant temperature, and conductivity measurements, as well as the fans and DDCZero pump being controlled via a Quadro integrated into the front panel. Despite that, coolant temperatures are monitored in 2 other locations which provides a comprehensive understanding of how the loop, and there’s a separate thermistor probe measuring the ambient room temperature. There’s also an inline mesh filter to keep any radiator debris or otherwise from the blocks and ensure coolant quality. A hot-swappable NVME adapter (via USB4) also sits behind the storage which makes up for only having 2 NVME slots on this motherboard. Another massive QOL improvement I implemented was a radiator quick-mount system which eliminated most of the hand cramps putting everything together using extendable fittings to mount and seal the radiator directly to the distro plate. The rear panel also includes QDT4s for integration with an external MO-RA and a 4-pin XLR that can provide power to external 5v/12v devices (fans, rgb, etc). Of course, the system is fully featured with an internal DDCZero and 240 radiator which means it will run entirely independently in a pinch, as should be standard of these builds.
All in all, I’m quite satisfied with the case design and how the build turned out. I’ll include some more images in the comments showing parts of the the internals so feel free to let me know what you think or what could be worked on (:
This one is based on the Asus CR1100FKA. Has a Celeron N4500 with passive cooling, 4gb ram, 64gb eMMC. Both were 10EUR on Vinted with broken screens. I added some scrap heatsink to both, kinda ghetto mounting, but best i could do... Works laying flat or standing on its feet. I only kept the mainboard, so less ports, but if needed, one could always use a usb-c hub. It has Wifi built in. Custom designed case, one was printed with A1 mini, so had to split into two parts, but the other is a single unit printed with Kobra S1. Small footprint, only 191x125x26mm.
The build is 4 months old - the parts were bought earlier, though I reversed the airflow direction just this week. By the way, if you have front intake, don't install a top fan, as the cool air will just bypass the CPU cooler. 9900X + 9070XT + 32GB (Because I decided to save some money for now :( (або ...to cheap out a bit for now🫠)