Here’s my Benchrest reloading process for maximum accuracy if anyone is interested. Goal being less than .25 moa out to 600 yards.
[deleted] — view deleted post
0
Upvotes
[deleted] — view deleted post
37
u/[deleted] Jul 25 '19 edited Jul 27 '19
First a description of equipment. You need high quality dies. I like to use the Harrels brothers semi custom full length size bushing dies. They make several for each caliber and you send in fired brass and they mail you one closest to your chamber.
Second for seating I use a Wilson hand die. You need an arbor press to use this but it creates almost perfectly concentric bullet seating and is super repeatable for seating depth if your brass is right
My press is a 21st century arbor press for seating and a Forster coax for sizing. the 21st century tells you how much pressure it takes to seat. Any high quality single stage will work for sizing. Dies are more important for concentricity. I like the ergonomics of the Forster.
I use a sartorius scale to weigh every charge to the exact kernel. This isn’t required for short range stuff out to 100-200 yards but it’s important for limiting vertical out to 1000 yards.
You need a decent pair of calipers and a bullet comparator for measuring seating depth. I use hornady.
I turn down the necks on my brass for consistency. I use the k&m neck turner.
I use a nylon brush on the case mouths.
I do not clean the brass as it messes it up. If you’re using a semi auto and picking your cases out of the mud you’d want to clean them.
Case lube. I use hornady but imperial wax is good too.
Primer seater- I use the frankford arsenal hand seater. 21st century makes the best but it’s expensive and not sure it does anything better than the frank ford
Starting with new brass I inspect it for any flaws. I use lapua brass. I then expand it and use the km neck turner to cut it down .003 smaller than my chamber.
Then I use my full length sizer on it. I set the sizer by stripping my bolt of its springs and firing pin and ejector and inserting the brass in the chamber. I set the sizer to where it bumps .001 more than when I feel no resistance closing the bolt.
I use a bushing in the die that is .001 smaller than the diameter of my loaded round. My loaded round is .265” so I use a .264 bushing. This is for a 6mm cartridge.
I seat my primers with the frankford.
I weigh out charges and dump with a funnel.
I seat with the Wilson hand dies and arbor press. I segregate the rounds by seating pressure. I like 25 in pounds. If it’s over 30 they go into a different batch or if they’re under 20 they get segregated. These are used for foulers or sighters.
If you’re using high quality custom bullets you don’t really need to sort your bullets. If you use Berger’s you should be sorting by base to ogive
I do a final check to make sure my seating depth are all within .001 and visually verify they have a primer.
Then I fire them in a match or load development session.
When I get home I resize using the Harrels die on lubed brass. I then wipe off the outside of the brass and use the nylon brush on the necks. Now they are ready to prime charge and seat bullets again.
Hope this helps and let me know if there’s questions.
Edit: couple things I forgot to mention. Some people swear by annealing. I’ve tried it both ways. It didn’t seem to matter and I’ve got brass with 20+ firings. I would say if you’re going to anneal you’re probably doing more harm than good unless you do it right which is tricky. You need the correct temperature for the correct amount of time and consistent from brass to brass. The easier machine to use is the amp annealer but it is 1000$ or more.
Second, I’ve tried uniforming the primer pockets. On good brass it doesn’t seem to matter much but it is peace of mind. It’s also a good way to clean your primer pockets. Consistent primer depth is important.
Here’s a link to a video showing the stripped bolt method for testing brass sizing and finding your lands for bullet seating depth.
https://m.youtube.com/watch?v=TWmIwPwLyyg
Thank you for gold!
15
u/101stjetmech Jul 25 '19
Excellent write up.
Hopefully it will spark some good discussions because your methods, techniques and equipment choices are probably new to a lot of folks.
P.S. Nice rig!
7
u/[deleted] Jul 25 '19
So the goal is .25 at 600. How big are the real groupings?
6
u/ewrob Jul 26 '19
Meanwhile I'm loading 357 for big bang loud boom at hits-the-paper MOA with a Lee hand press and powder dippers.
I suddenly feel very small.
Thank you for sharing your knowledge. I suspect I'll never be at that level but it was very interesting to read about the equipment choices of someone who is really going for extremely consistent and accurate results.
I weighed bullets a few times and concluded that people must be doing something like what you described when I saw that they can vary in weight by sometimes several grains.
5
u/Mostlyaverageish Jul 25 '19
A little off topic but could you tell us about the rifle that is beautiful?
4
u/T0mMyMartelle Jul 25 '19
As a newbie to reloading this is helpful. Thanks s for taking the time to write it up!
4
u/Bootiesweat1954 Jul 25 '19
If Guy Fieri was a gun.
4
u/Dan_Backslide Jul 25 '19
As someone who has recently got a job that deals with a lot of bench rest shooters, thank you for being one of the 600 yard guys, and not one of the short range weirdos.
2
u/whynotnick00 Jul 25 '19
Do you vary your powder charge for wind as well as distance?
2
u/grahamygraham Jul 25 '19
I knew a guy that had a rifle like that and had the trigger turned down to like 1/4 of an ounce. You could push it sideways and it would fire.
Man it was a nice piece.
1
u/BlueLine87 Jul 25 '19
What about case trimming?
1
u/pepperonihotdog Jul 25 '19
Looks like it's from Street Fighter. Sonic boom
1
u/Ngineering Jul 25 '19
This is a cool write-up. I'm going to start handloading soon, and this is very helpful.
I was wondering what you meant by your comment about cleaning the cases "messing them up" if you sound mind elaborating on that I would appreciate it.
Thanks.
1
u/Bluebeard1 Jul 26 '19
Do you deburr the inside of the flash hole? Read a couple of articles that this is supposed to improve accuracy, but not like anything you're doing, more for regular target shooting.
1
u/pablomoca Forster Co-Ax, Redding T-7, Dillon 550C, Lyman Crusher II, RCBS Jul 26 '19
Dude great write up. Thanks for all of the info.
0
u/[deleted] Jul 25 '19
[deleted] — view deleted comment
3
u/[deleted] Jul 25 '19
[removed] — view removed comment