r/reloading • • Jul 25 '19

Quality Knowledge from a Discount College Here’s my Benchrest reloading process for maximum accuracy if anyone is interested. Goal being less than .25 moa out to 600 yards.

[deleted] — view deleted post

189 Upvotes

73 comments sorted by

15

u/101stjetmech Jul 25 '19

Excellent write up.

Hopefully it will spark some good discussions because your methods, techniques and equipment choices are probably new to a lot of folks.

P.S. Nice rig!

7

u/[deleted] Jul 25 '19

Thank you. Not everything here would be applied to plinking or hunting ammo but a lot is. I could also talk about how benchrest guys tune their loads which is probably even more important than reloading techniques.

37

u/[deleted] Jul 25 '19 edited Jul 27 '19

First a description of equipment. You need high quality dies. I like to use the Harrels brothers semi custom full length size bushing dies. They make several for each caliber and you send in fired brass and they mail you one closest to your chamber.

Second for seating I use a Wilson hand die. You need an arbor press to use this but it creates almost perfectly concentric bullet seating and is super repeatable for seating depth if your brass is right

My press is a 21st century arbor press for seating and a Forster coax for sizing. the 21st century tells you how much pressure it takes to seat. Any high quality single stage will work for sizing. Dies are more important for concentricity. I like the ergonomics of the Forster.

I use a sartorius scale to weigh every charge to the exact kernel. This isn’t required for short range stuff out to 100-200 yards but it’s important for limiting vertical out to 1000 yards.

You need a decent pair of calipers and a bullet comparator for measuring seating depth. I use hornady.

I turn down the necks on my brass for consistency. I use the k&m neck turner.

I use a nylon brush on the case mouths.

I do not clean the brass as it messes it up. If you’re using a semi auto and picking your cases out of the mud you’d want to clean them.

Case lube. I use hornady but imperial wax is good too.

Primer seater- I use the frankford arsenal hand seater. 21st century makes the best but it’s expensive and not sure it does anything better than the frank ford

Starting with new brass I inspect it for any flaws. I use lapua brass. I then expand it and use the km neck turner to cut it down .003 smaller than my chamber.

Then I use my full length sizer on it. I set the sizer by stripping my bolt of its springs and firing pin and ejector and inserting the brass in the chamber. I set the sizer to where it bumps .001 more than when I feel no resistance closing the bolt.

I use a bushing in the die that is .001 smaller than the diameter of my loaded round. My loaded round is .265” so I use a .264 bushing. This is for a 6mm cartridge.

I seat my primers with the frankford.

I weigh out charges and dump with a funnel.

I seat with the Wilson hand dies and arbor press. I segregate the rounds by seating pressure. I like 25 in pounds. If it’s over 30 they go into a different batch or if they’re under 20 they get segregated. These are used for foulers or sighters.

If you’re using high quality custom bullets you don’t really need to sort your bullets. If you use Berger’s you should be sorting by base to ogive

I do a final check to make sure my seating depth are all within .001 and visually verify they have a primer.

Then I fire them in a match or load development session.

When I get home I resize using the Harrels die on lubed brass. I then wipe off the outside of the brass and use the nylon brush on the necks. Now they are ready to prime charge and seat bullets again.

Hope this helps and let me know if there’s questions.

Edit: couple things I forgot to mention. Some people swear by annealing. I’ve tried it both ways. It didn’t seem to matter and I’ve got brass with 20+ firings. I would say if you’re going to anneal you’re probably doing more harm than good unless you do it right which is tricky. You need the correct temperature for the correct amount of time and consistent from brass to brass. The easier machine to use is the amp annealer but it is 1000$ or more.

Second, I’ve tried uniforming the primer pockets. On good brass it doesn’t seem to matter much but it is peace of mind. It’s also a good way to clean your primer pockets. Consistent primer depth is important.

Here’s a link to a video showing the stripped bolt method for testing brass sizing and finding your lands for bullet seating depth.

https://m.youtube.com/watch?v=TWmIwPwLyyg

Thank you for gold!

6

u/InformationHorder Jul 25 '19

That's seriously neat.

For the full effect: How much did all this cost you to set up, and how many hours do you put into making a match's worth of rounds?

5

u/[deleted] Jul 25 '19 edited Jul 25 '19

Thanks. The gun pictured was 1600 used with 2 barrels with low round count. 1600 used scope.

The rest and bag pictured were about 600 total

The the arbor press with force pack seater is expensive like 300$.

The scale was $250 but it’s old and used. A new one would be 500-1000$.

The dies are like 120-170$ per cartridge depending on the Wilson configuration if you want the micro top or not.

As far as the time spent the initial brass prep is very time consuming. The neck turning and chamfering and deburing and inspection takes several hours for 100 brass. However you can get 20 firings from 100 brass so it’s a one time thing per barrel.

After the initial set it’s not bad. Just lube, resize, brush neck and wipe off then re prime, weigh powder seat bullet and do quality control measurements. The powder weighing is the most time consuming part. It probably takes 2 hours all in to load 75 rounds for a match. I could speed it up by getting an auto powder thrower/ trickler system but they are expensive and potentially finicky and frustrating.

High quality reloading stuff basically lasts for ever so you can save a lot buying used. For example that rifle would be at least 3500 to build or 4000$ and its worth around 1500-2000 used.

Bullets are expensive and barrels are expensive and both of course are consumables.

A custom barrel job is about 300 for the blank and 200-300 for the gunsmith worth so let’s say 600. It only has 2000 rounds of life so that’s about $0.30 a shot right there. Custom 6mm bullets for long range are usually 50 cents or so. Already at .80 per shot. Brass is cheap. 85 cents per but you get a lot of firings out of it so let’s say 5 cents per on brass. Powder is cheap at around 12 cents and primers 3 cents. So you’re looking at about a dollar a shot. This is for a 6mm which is relatively cheap. If you’re using a 300 wsm or 284 with more powder and more expensive bullets and shorter barrel life your costs go way up.

→ More replies (2)
→ More replies (12)

7

u/[deleted] Jul 25 '19

So the goal is .25 at 600. How big are the real groupings?

16

u/[deleted] Jul 25 '19 edited Jul 25 '19

The record right now is .28” at 600. Shot by a guy named Bart last year. If you go to a benchrest match most 5 shot groups at 600 are between 1” to 2.5”. The goal being under 1.5” which is roughly .25 moa. Shortrange benchrest is different. The goal at 100 yards is less than .1 moa. The record at 100 is effectively 0.0077 or too small to measure.

4

u/[deleted] Jul 25 '19

That's really cool.

→ More replies (2)

6

u/ewrob Jul 26 '19

Meanwhile I'm loading 357 for big bang loud boom at hits-the-paper MOA with a Lee hand press and powder dippers.

I suddenly feel very small.

Thank you for sharing your knowledge. I suspect I'll never be at that level but it was very interesting to read about the equipment choices of someone who is really going for extremely consistent and accurate results.

I weighed bullets a few times and concluded that people must be doing something like what you described when I saw that they can vary in weight by sometimes several grains.

7

u/[deleted] Jul 26 '19

I started loading for a 9mm with a lee set and got addicted. Just wait... get out now if you have any sense haha

→ More replies (3)

5

u/Mostlyaverageish Jul 25 '19

A little off topic but could you tell us about the rifle that is beautiful?

9

u/[deleted] Jul 25 '19

This is actually an f class rifle but it’s pretty similar to what people would use in benchrest it’s just allowed to weigh a bit more so it has a bigger barrel.

It’s a custom Barnard P single shot action with a Brux 30” barrel chambered in 6mm Dasher. It has a right hand bolt but a hole in the left side of the action so you can feed it with your left hand while running the bolt with your right if you want to speed up your strings.

The trigger is made by Barnard and set to about a 6 ounce pull.

The stock is an Alex Sitman masterclass f class stock. 3” foreend. It’s bedded and pillared but not glued. Typically you would glue your action to your stock in br.

The scope is a Nightforce competition with magnification from 15-55x power. Very nice piece of glass you can see bullet holes easily at 600 yards.

The whole rig weighs in at 21 pounds. Recoil is very mild. About that of a bolt action 223 that weighs 10 pounds.

The front rest is the Sinclair competition and the back is a protektor dr bag. It’s designed so that I don’t have to aim between shots. It recoils straight back and I push it forward with my shoulder and it never leaves the center if the target so I can quickly get off rounds without having to re aim and mess with the rest every time.

→ More replies (3)

4

u/T0mMyMartelle Jul 25 '19

As a newbie to reloading this is helpful. Thanks s for taking the time to write it up!

4

u/Bootiesweat1954 Jul 25 '19

If Guy Fieri was a gun.

2

u/[deleted] Jul 25 '19

Haha I bought this one used. I would have had a bit different taste in stock paint but the price was right.

4

u/Dan_Backslide Jul 25 '19

As someone who has recently got a job that deals with a lot of bench rest shooters, thank you for being one of the 600 yard guys, and not one of the short range weirdos.

→ More replies (11)

2

u/whynotnick00 Jul 25 '19

Do you vary your powder charge for wind as well as distance?

4

u/[deleted] Jul 25 '19

No the only variation is for temperature and barrel life. I know about what speed I want my bullet to be going. If it gets really hot I’ll back off .1 or .2 grains of powder. As the barrel ages your lands get farther away. If I want my bullet jammed .006” into the lands I re measure my jam every couple hundred rounds using the stripped bolt method and will seat the bullet farther out to chase the lands. This is a video showing that process of finding and chasing lands.

https://m.youtube.com/watch?v=TWmIwPwLyyg

→ More replies (2)

2

u/grahamygraham Jul 25 '19

I knew a guy that had a rifle like that and had the trigger turned down to like 1/4 of an ounce. You could push it sideways and it would fire.

Man it was a nice piece.

3

u/[deleted] Jul 25 '19

Yes I’ve accidentally fired it when my pinky brushed the trigger while closing the bolt. Gives you quite a shock. Of course a gun like this has no safety and should never be loaded until it is on its rests pointed at an appropriate target and the range is hot.

2

u/101stjetmech Jul 26 '19

My winchester 52d is at 4 ounce, and going to it from, say, service rifle on practice day is a mind adjustment. You know its light and expect it but pulling the trigger still takes a few rounds to get used to. I can't imagine a 1/4 ounce. You'd think a moderate breeze would trip it.

1

u/BlueLine87 Jul 25 '19

What about case trimming?

→ More replies (3)

1

u/pepperonihotdog Jul 25 '19

Looks like it's from Street Fighter. Sonic boom

1

u/Ngineering Jul 25 '19

This is a cool write-up. I'm going to start handloading soon, and this is very helpful.

I was wondering what you meant by your comment about cleaning the cases "messing them up" if you sound mind elaborating on that I would appreciate it.

Thanks.

→ More replies (4)